Видео

Its about 5 miles from my house 😃

A couple of points. 1. Don’t need to use a drill to remove the plastic cap that covers the wheel bearings and the bolt holding the wheel to the axle. There is a little notch on the cap for a small flathead screw driver to remove the cap (has Swiss emblem on it). 2. The wheels are 64mm dia by 24mm wide. The axle looks to be 6mm.

Thanks!

This is 2wd right?

Okay, i feel stupid for asking, but will this work if i have motor oil in the tank?

Waiakea is not owned by a native Hawaiian it’s owned by a white haole from LA. Rich spoiled privileged haole buying rights to a aquifer in the big island. Waiakea is basically tap water from an aquifer in the big island they than ship to California to process it. I stay away from these whitewashed companies with false advertising

Hey my lawn mower shakes violently and smokes, the blade is all clean nothing trapped inside anyone know what it could be?

QUESTION: Can the gas tank of a Craftsman Riding Mower be removed in this same type of way? Is there a video that might show how to clean the fuel tank of a Craftsman Riding Mower?

Great video. Thank you sir.

Did you say "Samsonite" briefcase? It looks like a Swiss Gear rolling briefcase.

that ain't kool aid she's drinking we know that much lol

Why didn't you solder the pins to the capacitor from under the board?

Well that’s not it

Thanks, friend. I watched a few other videos on the same topic, and invariably they involve buying a couple of tools, as well as the new stem. "I detect some bullshit", my dull little brain observed. Your video got it just right, without trying to sell me something I don't need. Much appreciated!

Samsung Briefcase? that's a Wenger Case. Good video though. By the way to remove the wheel it's much easier to do than how you did it. But again, at least you did it and showed how to do it with this video. Thank you.

TANKS!

I’ll try this Sounds loud tho ? Thanks

mine vibrates only when blades arent engaged

Thanks for this! I had watched another video that wanted to use the actual rachet but that seemed sketch. This ended up being much easier because i was able to feel my progress and loosen the strap as i went. Thanks again!

Such an easy fix. Thank you. I had been wrestling with my pull behind aerator tires. I used a tow rope with hooks on each end. Save me some time. Much appreciated!

Yikes, do not rip capacitors off the board! Properly desolder them! You got very lucky you didn't rip the solder pads off the board. There's also enough room in there you wouldn't have to replace it with a surface-mount capacitor. You could much more easily solder the legs of a through-hole style capacitor onto those pads and call it a day!

Very good video helpful thank you 🎉😂

My sincere thanks!

Best I've for this type of vid, thorough and speedy. Thank you

Where are you located?

I'm curious to learn how you determined the capacitor was the defective component. Thank you for publishing your video.

Buy hospital grade outlets. They won't break.

Very cool

Did the 100uf cap replacement today with a 220uf 50v ... after attach to board it was showing 203uf. still the display will not come up broke 2 of the vents as well out of ideas now ...

I used to repair clusters some years ago and one tip if are interested, If you are replacing one capacitor with a larger one due to what it seems the incorrect one chosen in the design (220uf instead of 100uf) as you are already spending time on removing all the board, is better to get an entire set of caps and replace all SMD and regular cylinder ones, when I used to repair I took my time to test all caps for my customers and a lot of them were still "good" when tested but leaking underneath and some other were off spec, so for the work done, replacing all is the greatest choice and try to spend some time with magnifying glass to make sure there all joints are healthy not cracked due to heat.

I also have the very same Victorinox Computer Travel Bag. However; you do not specified the wheel measurements of the replacement for example: 64mm/24mm and most important the "Bearing size" was it 6mm or 8mm??? Thank you

Can you share the link you used got the new wheel & axel from?

Would this have anything to do with my turn signal lights not working?

Thank you for the video helpful

👍🏾

I performed this repair on a 2005 Prius and I haven't had a blank speedometer since. This repair works great. It was a little tricky to remove the display from the dash, but it was worth it.

You know a lot about finding things well water wise pretty cool 😮

Question? do you know if an 03 highlander v6 has camber adjustment like this? I changed the control arms and ball joints and my camber is way out ty

Very well explained,

Very nicely done. You did not go into how you decided that particular capacitor was bad and not any of the others.

How did you take the gas tank apart??? Why skip that

I soak my filter in clean gas and agitate the gas through the filter to clean all the dirt out. Water takes too long to dry. I also put a little clean gas in my tank move it around then pour it out to clean the tank.

Worked great. Thanks!

Que pasa si el intermatic parpadea y no enciende

Awesome, saved my tire! Thanks dude!

Does this work for Prius gen 3 from 2010, 2011 ? Thanks

Hello brother I have a 2016 Rav 4 when I went to alignment check my rear camber is off I had a rear accident a year ago. I heard in toyota rear camber shouldn’t change unless there is an accident. How I fix this issue please help.

Sheesh! Why don't I check RUclips sooner. I had a pretty stiff tire so I had to use the ratchet and crank down on it a bit. Worked like a champ on my snowblower. Thanks man.

Great video. I am not ready to go to this level to fix yet on my 2009 Prius. Using the hack method at the moment to restore dash. With Prius powered off, driver side door open, step on brake and simultaneously turn headlights on and off rapidly. Red open door light will turn on and dash will work. Guessing this may discharge the capacitor as a sort of reset??

thanks