Видео

Followed same exact solution however even after solution convergence i am not seeing a rise in temperature

Hi @EngineeringNature, thanks for the video... can you publish another video on this kind of study but in a 3D meshing version? Can you include the phenomena when it causes phase change, especially during expansion? Thank you

Bro, can you please give the link to the research paper which you referred to for this analysis.

bhai ye geometry kaha se mila hai link share kar sakte ho

Very nice video. I have a question, how can I had an insulation to this pipe because when I try to do it, it just increase the thickness of the pipe?

Did you video with CFX 3D Model?

Can u please share your mail ID ....I need to discuss something from you.

I have one paid project .Are you interested to do this project?

Why do you need an outlet ? You make the fuel injection into a constant vessel.

hi you use 0.72 n/m for surface tension. it should be 0.072 n/m

Excellent video. I was able to replicate it. Can you please do a tutorial for combustion using species transport? thanks

labew brother

Hi, please i have issue with the model/geometry. I am finding it difficult to integrate the bluff body

you did not define temperature of bluff body

very useful, i'm from 2024

Thanks

What a great video I need your email sir

how to determine cell height?

Hey i get a floating point exception following the exact tutorials. The reason is one of the values is being initialized to a very high value. Can you please suggest what could drive this?

Sir can you also share video of hydrogen and air mixed Combustion proccess

Sir please can you give reference of the Paper of Brookes et al I cant find that paper .

Respected Sir, I tried it but its not working could you please help.?

Sir I am beginner and facing some problem could yoj please help.

How can i adjust injection point i mean there is only adjustable x position value for injection but i can't use carry injection point to a specific position depends on also y axis

hello i want to do the hydrogen air premixed combustion so for that i need hydrogen air mixture file so how can i create that?? plz tell me

Thank you! My first successful combustion simulation.

How can we set particular injection pressure?

Sir can you please make tutorial on study of cavitation in diesel injector nozzle (ruclips.net/video/ASbKmvygQEo/видео.htmlsi=ccmY17-n-EjWMG6R) the link i have shared is very similar but caitation is not clear from that video, I have cleared many doubts about cavitation from your channel. Waiting for your response plz

Sir can you please make tutorial on study of cavitation in diesel injector nozzle (ruclips.net/video/ASbKmvygQEo/видео.htmlsi=ccmY17-n-EjWMG6R) the link i have shared is very similar but caitation is not clear from that video, I have cleared many doubts about cavitation from your channel. Waiting for your response plz

Sir can you please make tutorial on study of cavitation in diesel injector nozzle (ruclips.net/video/ASbKmvygQEo/видео.htmlsi=ccmY17-n-EjWMG6R) the link i have shared is very similar but caitation is not clear from that video, I have cleared many doubts about cavitation from your channel. Waiting for your response plz

hi sir! great lecture. Can you send me or post your email id , I have some question regarding a problem I m working on? thank you.

👏

Very nice tutorials sir. Thank you so much

Cant we select laminar model instead of turbulent ( for orifice in microchannel - study)? Also if we take inlet boundary condition as inlet velocity, then what is the range of velocity that we can give here? Kindly guide

my mesh fails due do conflict in regions for a u bent pipe.

Hi sir, I tried this using species transport but the mixture didn t ignite, do you have a suggestion for me please?

Sir is it possible to analyze mixing of co2 gas with cold water in a pressurized vessel in ansys fluent. Suppose a vessel is in vertical shape( 400mm diameter × 1700mm height × 3mm thickness) and vessel is half packed with series of perforated plates and then we pressurized that vessel from co2 gas up to 5 bar which will remain constant throughout the simulation or process.Consider half inch duct for co2 gas inlet from any side of vessel and then with the help of high pressure pump, cold water(2 degree celsius, volume flow rate 4 cubic meter per hour)is sprayed through nozzles from the top of vessel towards bottom. My goal is to look out how water is passing through those perforated plates and at last how much co2 gas is mixed in water which is going to be stored in the bottom of the tank . Consider 1.5 inch duct for water inlet and 1.5 inch duct for water outlet which is open to environmental pressure. Kindly explain how to do in ansys fluent . Thanks a lot 🙏.

Thank you so much for the video. Could you please tell how the boundary conditions of air and fuel inlet mass flow is calculated. Is it assumed to be the same value as 3D case or do we need to make changes for the actual values for 2D. or is it accounted when you gave hydraulic diameter ?. Thanks once again!

Nice Lecture Sir, 👍👍👍 I need your help with regard LES and DES for non viscus flow for two phase simulation. can you give me some linke which is helpful to understand the basic concept.

sir how to get area in reference value? is it car area ?

You're a life saver. Thank you!

hello, can you explain why the pressure at the exit is higher than the inlet, and we saw in your set up you choose the pressure inlet to be higher but in the results its the opposite. Thank you

do you have a paper validating the result

Sir, how to get the pdf wastewater treatment by hydrodynamic cavitation

Can you please make video on micro pre mixed Combustion simulation with the help of chemkin mechanism.

Hi Sir, how can simulate fire model for car ? how to model the smoke and visibility by using ansys fluent?

Can you please guide how to take average values of iterations we performed. And plot against those avg values

Hello. Thank you for the video. I have a question. At the start of the video it is shown an equivalent fuel/ar ratio of 0.61, but in the video, you don't set any fuel/air ratio. In general, there is no setting regarding the amount of fuel. How does the software understand that the incoming mixture has a fuel/air ratio of 0.61? Thank you.

Can you plz make a dynamic mesh video of this cylinder with valves and their timings

Hello. Thank you for the video. It is very useful. I tried the tutorial, but I run into the "Floating point exception" error when I start the calculation. What could it be about? Thank you 😁