Видео

Would you suggest doing the bearings at the same time or just replace based on wear? Also, did this engine have the oil consumption issue and did the honing and rings take care of it?

Great video!!! If timing mark is not lined up when you start to put belt on dows it matter what direction you turn it to line it up?

Thanks for this bro, I’m about to tackle this job, and this helps a lot

You’re from Nigeria. I can hear it.

Did you finish this?

Cual era la falla que lo producia o que pieza soluciono el problema.

how bad was the removal and installation?

Awesome video thank you sir, hope everyone subscribe this help me a lot.

What all you did to the exhaust

That’s an E61, not E39

You can bleed it without a techstream tool. Pump method works. Brake fluid might have water in the system. You have to re calibrate the ecb and vsc modules its a pin method on doing it

Where are you located man can you do this for my truck

❤ thanks for this video one of the only ones that really explains in detail the way the timing marks is supposed to be The only thing that I find troubling about the way Nissan has this setup is that how do you know the cams are in the right position can you put the chain on those top links can be a little bit to the left or the right won't be exactly right how come they don't have marks on the Block where you line up the lines on the cams? It's just supposed to be that the lines on the cams are just supposed to Face straight up

Do you have the whole video

What a waste of time!!! You are clearly not a professional!! That was nail biting viewing and the fact that the timing noise is the same and hasn’t changed very much is significantly more nail biting than the whole video… Ohh that poor Nissan juke is going to go bang !💥

What is the engine again?

You didn’t replace the seal on the studs and they came in the felpro valve cover gasket kit. You gonna do a job do it correctly

Done incorrectly

at ruclips.net/video/ZIsvDB65O20/видео.htmlsi=JqFn2irkoDi9pkVq&t=1230 , you rotated the camshaft mark to get it align with the new timing belt, isnt that a no no?

Awesome video! Just a question, before installing head gasket and after you applied silicon. What kind did you use? Thanks in advance.

It’s coming from the Abs unit, the brake switches was the cause of the no start I got another video where I got it to run..but been waiting on my customer to approve the abs unit to also fix the buzzing noise 5:07

Where are you located????

Ever figure out the issue with this? Im having same problem

Having this issue right now but with both of my rear lights, my recerse and brake lights work but the rear light just doesn’t light up unless I press on the brake

Thank you so much for sharing!!

Great video! Im replacing my connecting rods since 2 bent 😣 any suggestions? I just have no idea how the timing will work!

Excellent, show each critical steps thank you very much

😂😂😂😂

Good work 💯 thank

thank you for the information. i will use this method

😂😂😂

What are those seals called that go in between the ladder frame and block

Was the cover aluminum or plastic ? 41:26

I was wondering if you took the other motor mount on the top and left the bottom but loosened the bolt would you be able to slide the engine just a bit to the right so the timing cover can go back on a little easy? I'm going to be needing to do this job just waiting till i my oil change is due so i can change the oil since I'm going to be dumping it out for the job. Thanks for the video great info

Tellem tellem

❤❤❤❤

Time for a beer for you. That job gave me anxiety just watching😂

I have a 1.6 hundyia tusson turbo 1000 hundred miles

Have exactly the same issue with my Juke 😢 Suspected it was the chain, thanks to you now I'm certain 😢 Thanks for the video and tips ❤

Did this engine actually run after this rebuild because I'm getting ready to start building my engine and I just couldn't find a build video or manual on putting the g4fj engine back together after tearing it down

Do you have to order the crankshaft from KIA? Ive seen a lot of cheap crankshafts for sale in a rebuild kit.

how was matinence on this?

How did the swap turnout?

How much does that repair cost? My engine is rattling passenger side …

How is the pin conecting the piston and rod held together?

Hey.

Eji, thanks for the great video. I have seen many videos of kia engine being taken apart, but not rebuild. 👍

I have a kia cerato 2009 it did over heating, after surfacing the cylinder head it started burning oil. My mechanic think it's best I get a new engine. Please what can I do as the engine runs fine but burns 1 litre under 300km.

Good job man going through everything so people can see, good content my friend.

By their accents you shall know them, love it