Видео

You said, make sure you fit the bearing correct way, same way as you have dismantled it, and at the end you have installed it the other way round. Check your footage.

This is fantastic. I got the crazy idea recently of replacing the driveshaft with a aluminum or carbon driveshaft on my adventure fan just to reduce rotational mass as well.

Another Great Video, I think my van needs this. I am getting strange rumbling sound above 60mph

what is the name of the part that you're replacing?

Would this timing chain replacement work on a 2008 Jeep Grand Cherokee with the Merc 3.0 liter OM642? Anyone in Phoenix AZ area? Asking for a friend... :)

wish me luck! I want to try this on a N47 BMW engine :). Ony advices before desister?

Awesome guys. Looking to buy a v6 Sprinter very soon here in Melbourne Australia & this will help bigly when I kick it in the guts first up 🫡 very clearly can hear your engine repair purring smoothly. Go Trump !

Hi i have sprinter in germany with 520 000 km and same probiem model 2018 what is problem

2024 and less than 17k mine is blowing cold air as well as defroster does not blow hot either. Consequently no windshield defrost. I just spoke with Orlando Mercedes and they told me that defrosters on Revels and sprinters do not blow hot air they only blow cold air. This does not make sense.

Just had the same issue come up in a 2019 with 45k miles. This needs to be a recall for sure. They said both recirc and blend door are faulty. Charging $1400 to fix.

1/4 8mm stub swivel socket for the one bolt so you do not have to remove the intake pipe.

Thank you for taking the time to make this video, it helps a lot!

👍

Om642 is king crab

I have a 2008 Sprinter that chain snapped while driving, do you think the engine is damaged? Should I do an engine swap? I’ve been reading about low end engine damage because of timing chain breaking. Thanks

om642 has a weak chain??!

Mine blows hot air 90% onlf the time. Then one day it wont for a few hours.

Hi , I assume this is a amazon retire delivery van? I have a same van, my is 2019 sprinter 2500, I have same problem that heater blow cold air, Also do you know wher is obd2 connect port on this van? seems amazon change the port from its original position. thanks for answer my question

Even the high pressure fuel pump needs to be timed

Bro, the litle holes in chain should be facing out....sorry...

You can put the big O-ring that comes with the oil filter (Mann HU821X) inside the vaccum pump as the aftermarket seal fails and this is a cheaper option, I haven't tried it yet but I know a few people who have and it worked. Also replace the metal gasket (MER-6420160280) where the pump mounts to the engine while you're at it as that will eventually leak as well. People have done it on 2012-2015 Ml, GL, R class with OM642 engine but I think it should work on all OM642 applications regardless of their model years. Remember to clean it really well like using a brake cleaner and lint free cloth before installing the gaskets to prevent any future leaks, and do it at your own risk as the vaccum is created for brakes!

For me tensioner it fixed the problem ,i just drove 20k km no ratling noise on morning maybe need to change it soon but right now is good

Did you convert a 2wd to a 4wd or 4x4? We have a 2013 High Roof 170 and I would love to convert ours. We tow a boat with some slippery, steep ramps and drive out on farms with Honey Bee equipment. Not extreme off-roading or anything like that. Thank you. P.S. Where are you located, we are in central Virginia.

Hi, I’m in the UK and my Van is a right hand drive will the location be on the opposite side of yours or same side?

Thanks for good explanation. Did you draw the new chain with the old chain tensioner in its place?

than you

Thanks for the video. I have a question re: parts. Inside Febi box is indeed an OE supplier's chain. However it is not the case for the tensioner, no? How Febi tensioners are behaving on a longer run? Any experience with INA? INA & Febi are made in Germany, Genuine MB is made in Romania. Thanks.

Mercedes-Benz is such a unreliable garbage car.W 203 was disaster. Ten the first version of w204 was a bit better and then mercedes screwed up with totality bad om651 engine.Injectors and timing chain and tensioners malfunctions. Om 651 have only 1 chain its simplex and previous one was duplex.I though nothing can be so bad as bmw n47 engine but i was so wrong Mercedes-Benz is one of the most unreliable vehicles Also when you changing that tensioners on mercedes you have to take engine out same as on n47 bmw.I will never buy any mercedes again.I will buy only Japanese products ( And yes,i do own W204) at the moment.

Im having the heat issue as well as air only coming from the face vents. Feet vents and window vents wont blow. Does this actuator solve that issue as well?

So you’re just going to keep using the old chain guides?

hi any chances i can call for somehelp?

bro do you need skilled workers in sprinter vans "specialist'' i mean?

am a Mercedes sprinter specialist if you interested in skilled workers!, i can give you my contact info and my CV when you needed it's either piston hand fatal or injectors prob still inspection needed

14:54 it is my understanding that the level when hot (180 degree) should be checked with the engine running and in neutral.

V6 diesel?

Im sorry but ist that beyond repair. Like the structural damage on top ? How could something like that be fixed ?

Without radiator?

Amazon 😂

Getting it's moisture from the ambient air!😂🎉

Damn

Probably works great until it stops adjusting. It's BMW parts, why not use the Mercedes S class or the big wagon seats? I know, they're hard to find. But anything other than bmw from my experiences with them.

That amazon special! ❤

Is it really that straightforward? Also was yours a 3.0 diesel?

Seems a little extreme!

Where are you located?

2011 GL350 here with 230K miles, and the last couple of days I’ve been hearing a constant light Slap ing sound on top of engine near the front drivers side camshaft.

hello! What is the difference between engines 651955 and 651957?

Having trouble figuring out how to get to the bolt on the back side of the power steering pump bracket. The two on the front were easy but the one that’s bolted to the side of the engine is tricky to tell where or how to get to it. Can you describe how to get to it and what kind of bolt it is?

How do you replace a broken camshaft sprocket on 08 Sprinter?

Great video. Do the seat rails bolt straight down to the sprinter seat boxes? Thanks