Видео

Dude what a genius got my morning coffee thanks to you

So there's no way to remove the seal without damaging it right? Like in my case i have a brand new side cover never used and i just put the new seal in in front of the ball bearings and when i went to slide it onto the Crankshaft it gets stuck about half way up the crank or so. Now in order to get it to fit all the way on i gotta sand the inner ball bearings but the seal is in the way and will end up getting sanded as well if i dont remove it first. Guess i have to take the loss and order new seals? 🤔

In your location, is it not required to protect the Romex cables in conduit?

Good Video 💫💯 New Subscriber 2025🎉 Author Gernel Darrell,📚📖 #Redemption #TUB #Bermuda King TUB from Bermuda Island 🇧🇲

I'm pretty sure the best instruction is on WoodPrix.

Hi can you share you plans for this , what do you recommend on a 12’x16’ shed how would you do the foundation

Use the popular music. That is how they come and hashtags

Hi BFF. I just wanted to let you know that I am watching and that I am your new internet BFF. Have a great day

I am your internet BFF whether you like it or not... 🤣😘

Look at those people "bothering" you (Just kidding) I see the neighbor in the orange shirt... I can tell he is a visitor

Thanks for the video. Can’t wait to get our boat up and running. 😁

Thanks for the helpful video.

What is the drip pan you used? because I have the same exact grill and I want to use the same one? Thanks in advance.

Great video! Im at the same point with my boat, about to install the floor. Your process was detailed and very helpful. Thank you!

Another thing to keep in mind is that there is a bushing on the top instead of a bearing. There is an actual 608 bearing on the bottom. They have been made that way for over 30 years. I took apart 90’s Shop Vacs, and they too, have a bushing on the top. Eventually, you will hear a whine noise. When that happens, all that needs done is to lubricate the top. The new Shop Vacs (post 2020) have a completely different motor design. They have the square shaped motor. I believe that they actually have two sealed ball bearings, and that actually is a good thing!

is there a reason why this would install but then be hard to pull out and push in?

Most definitely needed an oil change. That was the blackest oil i ever seen 😅

I love shed build videos and you did a lot of good stuff here, but you put your walls up on the outside of this structure that has no footings bearing the load to the ground. It also has corners that are only held together by screws. You at the very least need mechanical fasteners, but what would be better, is have your deck blocks in the corners of your structure to bear the weight down to the ground instead of where you have them. This seems like it has potential to begin crowning in the middle over time as the weight of the walls push down on the outside.

my problem is generic holder keeps lid from closing enough unless push hard/slam lid

Will it work on 2018

U hv low iq u not gonna buy a new tv or take your tv off the wall

ty sir!!!

hey how much money did you spend on that project ?

Didn't show the first step of how to unlock the drawer slide. Useless video for beginners

Great video!! I do pressure washing and soft washing and use 12v pumps. I will say that it’s Very beneficial to use non collapsible hose on the suction side of your pump.

⛔️⛔️YOU ARE A G‼️ 💯🫡

Oughta pay ya to come do mine neighbor 😅

What to do when u press the rubber for the gasoline to full but it doesn't?

Thank you!!! God Bless you 🙏🏻🙏🏻🙏🏻

You didnt turn the a/c circuit breaker off first ?

Hi, I would like to make the foundation as you did, seems to be very simple. But put all that load just on 2 main beams don’t allot to bend the structure down?

Just opened my tv after on off cycle, had some veryticle lines too previous weeks, VAPING MOISTURE EVERYWHERE INSIDE THE TV

Thanks for the video very helpful I've resolved the issue in my vacuum it was the same problem Lake explained in the video thank you again.

did you find your car ran any better after the new transmission fluid?

Great video, very motivating.thanks

Never use sand paper in or around an open engine cover, there is a risk of getting sand in the engine oil. Only use a scotch brite pad.

I forgot to empty the gas tank before putting it away. What can I do to ge the generator running again? What do I do with the old gas from the tank? Can I still add gas stabilizer to the tank and reuse the gas? Thanks.

I just did a drain and fill and I put 4 quarts plus a bottle of Seafoam trans tune and Dipstick still doesn't even show a level

my fans never kick in, or maybe I don't hear them?

FYI the black 18in Long Neck funnel from Harbor Freight fits tightly OVER the dipstick tube and fills quickly. The 2009 manual notes filling via dipstick tube.

Nice work. Thanks man!

I find that as the switches get a few years old, they require more and more pulling force. Finally, one day, they require so much force "to switch," they break when you yank on the chain. Finally, when one switch started getting difficult, I sprayed it with WD-40 "Dry Formula" Amazon item number B00AF0ODGM . I used the narrow tube that comes with the can, stuck the tube into the hole where the chain comes out, just a little goes a long way, and immediately the chain started pulling VERY easily, which is apparently much appreciated by the switch. Without needing to apply so much force to pull the chain, the switch isn't so quick to break. Other parts of the switch may wear out after a few thousand switchings, but the lube keeps the switch from breaking after a few hundred switchings.

hey question for smt not covered in this video - how do I make sure i don't drill through the cabinet with the pilot hole? My cabinet side happens to be the side of the island so it'll be visible if i drill too deep lol. First timer here! thank you!

Yours is Highly professional but I have also built the same size 🤣🥰 and material was about $1100 in total still standing firm, no leaking anywhere after 5 years and amazingly straight flooring eventhough I never bothered to check if the ground is leveled . It is solving the purpose though if not close to yours.

Thank goodness. I have a new personalized plaque I need to hang in my home office and I had never seen sliding hooks before. Thank you for the video!

I loved the video! One question; why did you put a hasp on the doors to lock them, but installed the hinges on the outside where they can be unscrewed?

Thank you for making this video! This video helped me fix the problem. 😊

18:15 what in the world is going on in the background? The Wild West??

I have Honda step wagon 2012 one side would not light up , so found out the switch was broken I changed it still no lights, changed the bulbs around change the switch around still the same problem, have any solutions?

If I don't have one of the crimp things can I use just black tape