Hello Garrett, I tried to download the Setup Checklist.I put in my name and email address and it wouldn't download for me . Please help as I have one special project for my wife who died in April.
Great Videos, now a great question for you: My Genmitsu 4030 Prover XL has been working great for 8 months or so, BUT now the z-axis just started studdering when moving up and down during the carve but only on the right 1/3 of the machine. What happens when I traverse it either offline or with PC connection both the down and up directions make the z-axis move down or both move it up. I thought it was the stepper motor, but when I use the manual twist knob it traverses up and down without issue. I also tried wiggling the wires to the stepper motor and traversing up and down with no effect. Do you think this could be a ant-backlash nut issue?
keenefx321, It's great that you're troubleshooting the issue with your machine. From your description, it sounds like the problem may indeed be related to the anti-backlash nut on the z-axis. I'd recommend checking the nut for any signs of wear or damage, and potentially considering replacing it to see if that resolves the studdering issue. Also consider reaching out to your machine manufacturer on this one, they will have great troubleshooting tips for your specific machine.
I watched all the RUclips videos saying to contact them if anyone had questions about bits. I’ve tried by email, website reply, phone for almost 3 weeks without a single response. Nothing. I would say horrible customer service but I wouldn’t know - I don’t think it exists
lalohibri9625, I'm sorry to hear about your experience trying to get in contact brother. Please give me a call at 812-200-0891 and we will get you taken care of my friend.
Hi Garritt!! Quick question, assuming I've set my XY and move to my hight point to set my z zero can I start my Projekt from there or must I move to my job zero?. A little problem I always have is that I home all to change bits, then go to job zero and if my tool is a little lower than the previous one I gauge into my work piece 😝. Simple really but I forget every time. Thanks for you're video hi from germany
TheSuperheimwerker, Hallo from the US! As long as you have set your Z zero at the highest point, you can start your project from there if you prefer. Just make sure your toolpath accounts for any differences in tool length. Happy woodworking!
I only broke a bit once. I do however, regularly cause other problems such as bit slipping due to not enough tension, piece shifting due to not enough tension.
eitantal726, It sounds like you're dealing with some common challenges in CNC woodworking. Proper tension is crucial to avoid issues like bit slipping and piece shifting. Keep practicing and experimenting with your settings to find the right balance.
#2 got me just yesterday, had the "acrylic" laid out in Portrait and did the programming in Landscape!! Ruined a $30 piece of acrylic! Now I have your Checklist sheets in my setup drawer!!
Oh, I forgot, I got an email at 4:31pm yesterday that the Calipers were available and got another email at 4:37pm with confirmation of order received!! 👏👏
PapawsWorkshop-gd7hw, Oh no, I'm sorry to hear about your mishap! It happens to the best of us. I'm glad you found the checklist sheets helpful for your setup - they can definitely help prevent those kinds of mistakes in the future.
Get the Setup Checklist here → link.idcwoodcraft.com/xi8r0n
Hello Garrett, I tried to download the Setup Checklist.I put in my name and email address and it wouldn't download for me . Please help as I have one special project for my wife who died in April.
Send me an email and we will send it right to you
garrett@idcwoodcraft.com
Garrett I love the check list. thank you for sharing it with me.
MrBwest9376, You're welcome! I'm glad you found the checklist helpful. Happy woodworking!
Great Videos, now a great question for you:
My Genmitsu 4030 Prover XL has been working great for 8 months or so, BUT now the z-axis just started studdering when moving up and down during the carve but only on the right 1/3 of the machine.
What happens when I traverse it either offline or with PC connection both the down and up directions make the z-axis move down or both move it up.
I thought it was the stepper motor, but when I use the manual twist knob it traverses up and down without issue.
I also tried wiggling the wires to the stepper motor and traversing up and down with no effect.
Do you think this could be a ant-backlash nut issue?
keenefx321, It's great that you're troubleshooting the issue with your machine. From your description, it sounds like the problem may indeed be related to the anti-backlash nut on the z-axis. I'd recommend checking the nut for any signs of wear or damage, and potentially considering replacing it to see if that resolves the studdering issue. Also consider reaching out to your machine manufacturer on this one, they will have great troubleshooting tips for your specific machine.
@@IDCWoodcraft Thank you for taking the time to respond, and keep making your very informative videos!
I watched all the RUclips videos saying to contact them if anyone had questions about bits. I’ve tried by email, website reply, phone for almost 3 weeks without a single response. Nothing. I would say horrible customer service but I wouldn’t know - I don’t think it exists
lalohibri9625, I'm sorry to hear about your experience trying to get in contact brother. Please give me a call at 812-200-0891 and we will get you taken care of my friend.
Thank you for the personal call - you’re advice really helped me!!
Hi Garritt!! Quick question, assuming I've set my XY and move to my hight point to set my z zero can I start my Projekt from there or must I move to my job zero?. A little problem I always have is that I home all to change bits, then go to job zero and if my tool is a little lower than the previous one I gauge into my work piece 😝. Simple really but I forget every time. Thanks for you're video hi from germany
TheSuperheimwerker, Hallo from the US! As long as you have set your Z zero at the highest point, you can start your project from there if you prefer. Just make sure your toolpath accounts for any differences in tool length. Happy woodworking!
Thanks garret. Nice explanation of the checklist. Like the way you transitioned into the need for calipers. Bought mine yest. Keep up the great work
samspade2519, Thanks for the support! Enjoy using your new calipers for your woodworking projects. Happy woodworking!
I only broke a bit once. I do however, regularly cause other problems such as bit slipping due to not enough tension, piece shifting due to not enough tension.
eitantal726, It sounds like you're dealing with some common challenges in CNC woodworking. Proper tension is crucial to avoid issues like bit slipping and piece shifting. Keep practicing and experimenting with your settings to find the right balance.
#2 got me just yesterday, had the "acrylic" laid out in Portrait and did the programming in Landscape!! Ruined a $30 piece of acrylic! Now I have your Checklist sheets in my setup drawer!!
Oh, I forgot, I got an email at 4:31pm yesterday that the Calipers were available and got another email at 4:37pm with confirmation of order received!! 👏👏
PapawsWorkshop-gd7hw, Oh no, I'm sorry to hear about your mishap! It happens to the best of us. I'm glad you found the checklist sheets helpful for your setup - they can definitely help prevent those kinds of mistakes in the future.
Good information
kevinrich4637, I'm glad you found the information helpful brother!
Thanks Garrett
JNewellworks, You're welcome! Happy woodworking!
@@IDCWoodcraft I ended up finally getting the checklist after I bought the calipers last night.