@A-1 Compressor: Would you recommend using Nylog as a gasket sealant during the valve plate repairs/replacements? Thank-You. -Ian S., Vancouver, BC, Canada
Hey brother can u tell me about Carlyle 06 E compressor head replacement right procedure when em changing metal gasket with complete head assembly then after replace creating sound from head due to becker n suction valve but i hv tried many times but couldn't succeed the old one discharge valve broken from top so than it was easily taken the suction gas
why you should not use the suction back reed on low temperature? only in medium to high temperature, and if I use for a working pressure of 15 to 10 psi. thank you for your attention. i am Brazilian technician.
nisw1918 you need an oil pump to add oil. Let the compressor run a while before adding oil. On an 06E compressor the oil level should be at the bottom 1/3 of the sight glass. It can be at the bottom and the level is still ok. 06D compressors should be about 1/2 sight glass. If the sight glass is low the oil is probably in the circuit. Do not add oil until you confirm it’s not in the circuit. The oil will coat the evaporator tubes so the refrigerant will not evaporate properly causing the compressor to flood back. Run the head pressure up to get the oil back to the compressor before adding oil. I have removed more oil than I have put it in. A system with too much oil will kill the compressor.
What could be cause this compressor ampere keep on hiking..let say it start with 39 Amp with in 15 minutes it become 56 Amp ...and the compressor trip on overload.
Hi sir I am from Iraq I have about 15 years experience in maintenance of cooling systems also over haul maintenance of centrifugal and reciprocating compressors can I work in your work shop thanks alot
Thanks A1. I'm going to attempt dissecting a 06 tomorrow and hopefully won't get fired.
Did u get fired?
It's very helpful for me for overhauling.Thanks
I use to grind yalls crankshafts. And ALOT of others as well. Altho that was bout ten years ago 🙁
Never forget to change out your oil and pull vacuume before opening service valves.
Very good information thanks brother
Good day, where could I purchase a work shop and parts manual for the compressor
where would the broken piece end up should we spend time looking for it in the system?
good tutorial sir
Thank you very instructive thank you so much
How do you diagnose broken valves? what are the symptoms?
@A-1 Compressor: Would you recommend using Nylog as a gasket sealant during the valve plate repairs/replacements? Thank-You. -Ian S., Vancouver, BC, Canada
Hello, can i use ure video for my french channel? frigoriste chaine du froid. TY
Good video thanks for sharing
good information thanks for sharing it.
Hey brother can u tell me about Carlyle 06 E compressor head replacement right procedure when em changing metal gasket with complete head assembly then after replace creating sound from head due to becker n suction valve but i hv tried many times but couldn't succeed the old one discharge valve broken from top so than it was easily taken the suction gas
good video
why you should not use the suction back reed on low temperature? only in medium to high temperature, and if I use for a working pressure of 15 to 10 psi.
thank you for your attention. i am Brazilian technician.
Can you make veidio about falts and how to make maintinance for it
By the way how do you add oil just open the plug and add or is there a sequence to it .Thanks again gave you a thumbs up
nisw1918 you need an oil pump to add oil. Let the compressor run a while before adding oil. On an 06E compressor the oil level should be at the bottom 1/3 of the sight glass. It can be at the bottom and the level is still ok. 06D compressors should be about 1/2 sight glass. If the sight glass is low the oil is probably in the circuit. Do not add oil until you confirm it’s not in the circuit. The oil will coat the evaporator tubes so the refrigerant will not evaporate properly causing the compressor to flood back. Run the head pressure up to get the oil back to the compressor before adding oil. I have removed more oil than I have put it in. A system with too much oil will kill the compressor.
Could you tell me.how to add refrigent to chiller centrifugal please
Hi. I have a problem with a compressor model carrier that discharge is bypass to oil pass. Can you help me?
Thank you sir
What could be cause this compressor ampere keep on hiking..let say it start with 39 Amp with in 15 minutes it become 56 Amp ...and the compressor trip on overload.
Antigão esse muito bom de manutenção.
hi , can you provide the video for main bearing installaion of 06E (carlyle) compressor, thanks in advance
ola necesitó el manual de fabricasio del compresor carrier
Like si vienes por la tarea 2 de Refrigeración
+Bastian Palavecino jajajajjajajajajaj no me esperaba esto
+Bastian Palavecino que significa este desorden ?
Nicolas Saez Luna
0ut
jajaja, vengo por lo mismo
que. altura tiene la vase que pisa los flores de. alta
los flaper
ধন্যবাদ
Nice sir thank
这什么牌子的制冷机
Hi sir I am from Iraq I have about 15 years experience in maintenance of cooling systems also over haul maintenance of centrifugal and reciprocating compressors can I work in your work shop thanks alot
Sir can i get ur fb page or any other platforms for discussion or facebook id etc ur response will be precious for me thank you.
Hello
I'm working at compressor overall please give me 1 chance Saudi Arabia my company name elmac
Hi
I want this piece👇