Thanks for posting, I've been considering this option because Dakota Digital kinda thinks too much of their product for our trucks. I also have an '84 which is down now spun rod or bearing haven't investigated yet, but I subscribed to your channel because I'm thinking of carbing a 5.3 not sure yet but I have a new 1406 carb on the truck now. Thanks again.
Very good video. I like the fact that you used a 12 pin connector on yours. I have this set in red or did I should say. Over a 6 month span I started losing LEDs on the speedo RPM panel. Started with the right blinker then the left and finally lost my high beam indicator from time to time till it just stopped. Shortly after I started losing the LEDS on the RPM gauge till just this month I lost the whole panel. I reordered a new one when I came across you video. I think most of my problems were with grounds, I hate automotive grounds. Hope I have it figured out this time.
Hi great video. I just installed these gauges. I know you want to use your sensors, but make sure the ohms resistance is the same on each individual sensor or your readings will be false.Thanks,Donnie
smokey2022Ssss yes you are correct and I have noted that I will not be using my own sensors. I will be using the ones that came with the cluster. I will edit the video to let others know this soon. Thanks for pointing that out.
when are you gonna do a install video if you dont me asking. and thanks for this video man i was just looking at thes gauges a few weeks ago and i really want them and thanks to this video i think i can wire them up
I have used several of your ideas they are awesome right now I’m tying up loose ends the green wire for the tack from my intelligence Tronics unit looks like I have to hook it to the white wire on my psi wiring harness Are you familiar with this Psi Wiring harness
Did you run the check engine wire into the connector? I have a 12 pin but running the check engine wire would make it 13... 1)high beam 2)right turn 3)left turn 4)water 5)oil 6)tach 7) speed 8)power 9) fuel) 10)ground 11)dimmer 12)brake **13) check engine
Lonnie's Garage (Puppetkicker) ive been debating on that or doing individual cobalt brand gauges. Also its awesome to see a another fellow Christian loving his Square body.
Lonnie's Garage (Puppetkicker) Thank you very much!!! One last quick question, this is in regards to your part 2 of this. When it comes to the cars own wiring, does the manual that comes with Intel state which wires to look for on the car model. Or did you figure the placement on your own.
travis malcolm sorry about that. I have since edited the video description for this. I will not be using my sensors that I have purchased separately from the kit. I will be using the ones that came with the gauges as it is programed to this setup.
PuppetKicker oh okay, good thing I didn't go with the 5.3's equipment lol. Do you plan on making a video on how you're going to do that setup? I'd like to know what other items I'll need to buy. Thanks again!
travis malcolm yes I will be making a video this week showing the rest of the install that will be covering how to wire it to the truck and how to install the gauges. I will be using the sensors that came with this dash cluster kit.
Chasemanuti I'm in the process of finishing my shop. I'll be installing them in my truck this weekend. I love how they look. I have already tested them and they look great.
I have an 86 GMC. Instead of a tach my truck has a large gas gauge and there's an empty gauge on the lower left. Does anyone have any idea what I should do if I want to fit this on my truck?
Lonnie's Garage, whats up lonnie, we just talked a few ago, listen my problem with my plug from the steering columb does not have numbers, it has letters and they are are not in alphabetical order I did change the steering columb once
Thanks for posting, I've been considering this option because Dakota Digital kinda thinks too much of their product for our trucks. I also have an '84 which is down now spun rod or bearing haven't investigated yet, but I subscribed to your channel because I'm thinking of carbing a 5.3 not sure yet but I have a new 1406 carb on the truck now. Thanks again.
Very good video. I like the fact that you used a 12 pin connector on yours. I have this set in red or did I should say. Over a 6 month span I started losing LEDs on the speedo RPM panel. Started with the right blinker then the left and finally lost my high beam indicator from time to time till it just stopped. Shortly after I started losing the LEDS on the RPM gauge till just this month I lost the whole panel. I reordered a new one when I came across you video. I think most of my problems were with grounds, I hate automotive grounds. Hope I have it figured out this time.
Very well documented congrats on the new gauges there gonna look great! I'm just gonna run stocks on my 92 Silverado lq4 swap
Hi great video. I just installed these gauges. I know you want to use your sensors, but make sure the ohms resistance is the same on each individual sensor or your readings will be false.Thanks,Donnie
smokey2022Ssss yes you are correct and I have noted that I will not be using my own sensors. I will be using the ones that came with the cluster. I will edit the video to let others know this soon. Thanks for pointing that out.
Where did you get the new wiring cluster blocks? I got a kit from intellitronix, it did not come with that, and that part makes sooo much sense.
Amazon
@@LonniesGarage how do I search it? What is it called? Brand? Thx.
just saw your video! very good! i did mine but i have no fuel reading! preciate advice
Good video, where did you get connector from and do you have a part number?
I got it from ebay. No part number.
Great video. Thanks for making it.
you are the best brother
when are you gonna do a install video if you dont me asking. and thanks for this video man i was just looking at thes gauges a few weeks ago and i really want them and thanks to this video i think i can wire them up
OldWhips -NewShitZ hope to have one up this weekend
I have used several of your ideas they are awesome right now I’m tying up loose ends the green wire for the tack from my intelligence Tronics unit looks like I have to hook it to the white wire on my psi wiring harness
Are you familiar with this Psi Wiring harness
If your harness is labeled for the tac then yes run that wire to the green one on the cluster that says tac
Interested in one rod my 97 Tahoe ,great video
Are you familiar with the 2004 pick ups that was the donor engine for my car the next thing I have to do is hook up the cruise control
I'm not sure on the cruise. I haven't did that yet.
Did you run the check engine wire into the connector? I have a 12 pin but running the check engine wire would make it 13...
1)high beam
2)right turn
3)left turn
4)water
5)oil
6)tach
7) speed
8)power
9) fuel)
10)ground
11)dimmer
12)brake
**13) check engine
No I didn't. I don't have mine hooked up currently.
@@LonniesGarage ok .I think I'll do the same thing.. thanks
3 years ago you installed the instrument panel... how she holding up my Brother?
It's OK. Some of the readings are off and the tac doesn't work.
Lonnie's Garage (Puppetkicker) ive been debating on that or doing individual cobalt brand gauges. Also its awesome to see a another fellow Christian loving his Square body.
Out the bocks would the parts work for an automatic transmission, or is it required to be a manual.
I'm running and auto transmission
Lonnie's Garage (Puppetkicker) Thank you very much!!! One last quick question, this is in regards to your part 2 of this. When it comes to the cars own wiring, does the manual that comes with Intel state which wires to look for on the car model. Or did you figure the placement on your own.
The tornado that hit Jonesboro destroyed my truck body. I have another one but had to start over as far as the body goes
your booking it up man!
Hey sorry I'm unable to see your reply, why can't we use the 5.3's stock sending unit or temp sensor? Thanks for the reply!
travis malcolm sorry about that. I have since edited the video description for this. I will not be using my sensors that I have purchased separately from the kit. I will be using the ones that came with the gauges as it is programed to this setup.
PuppetKicker oh okay, good thing I didn't go with the 5.3's equipment lol. Do you plan on making a video on how you're going to do that setup? I'd like to know what other items I'll need to buy. Thanks again!
travis malcolm yes I will be making a video this week showing the rest of the install that will be covering how to wire it to the truck and how to install the gauges. I will be using the sensors that came with this dash cluster kit.
great video
83c10chevy Ty. Part 2 soon to come
nice...thanks for the video...send me that sending unit and circuit board too..lol
Are all power wires hooked up to ign on?
Yes
@@LonniesGarage Thank you!
Have you had any problems with your Gauges since then.....
Brandon Vallier keep watching the videos that follow this one. I've since sent them back.
What is your source for the female connector for the stock instrument cluster connector?
Joe Taylor I didn't end up getting the female connector
PuppetKicker thanks for the reply.
Yes I’m right down the road just outside walnut ridge Ar
Good deal. Hit me up on Facebook. Lonnie Rice.....
Truck frame is in Bernie mo. At my buddies shop
How do you like them? I was about to order the same ones
Chasemanuti I'm in the process of finishing my shop. I'll be installing them in my truck this weekend. I love how they look. I have already tested them and they look great.
PuppetKicker I'm doing the exact same build, just curios why you didn't tap into the 5.3's temp sensor and oil sending unit?
Thanks so much!
How much was this setup? Just bought a 78 chevy k10.
Dont wast your time or money
I want to do this but I'm kind of scared too
when are u doing more mower builds
Eric Miller when the mood hits me
I have an 86 GMC. Instead of a tach my truck has a large gas gauge and there's an empty gauge on the lower left. Does anyone have any idea what I should do if I want to fit this on my truck?
A clock
sounds good
I need to hire you. Really
Wow thanks bro......
Brandon Vallier no problem
Lonnie's Garage, whats up lonnie, we just talked a few ago, listen my problem with my plug from the steering columb does not have numbers, it has letters and they are are not in alphabetical order I did change the steering columb once
hi I'm dylan you've seen me in town I want to see the truco
DylanFerrell Vlogs holler at me tomorrow sometime
That did it
I will pay you to hook my upI got the intellitronix for 2002 mustang
Where u from?
I need to get a frame sand blasted anyone close to nea or semo
What town u from. I'm in Senath Missouri. Ever heard of it?
Tex me if you know anyone that sandblast