Back in 2000 as an electronics hobbyist at that time i was designing on paper and making myself the PCBs for fun, electronic door bell, small radios, cable TV amplifiers, etc using nail paint and nitric acid, and as for drilling, i was making the drills manually with a small device. Took me hours to complete something but every time in the end I was so happy that i did another working PCB without any mistakes.
Cris33311 Прямо с языка сорвал . Один в один! Азотную кислоту не применял. Хлорное железо, само собой потом: Перекись водорода+ слабенький р-р HCl _или медный купорос с солью. Получалось просто зашибись. Самое "тяжёлое"- нарисовать красиво, без " соплей"и пропусков. И лаки, у жены украденные, и всевозможные нитрокраски- всё испробовал.. ...давно это было... А лучшего человечество и не придумало... Кроме как травить....
It's very easy to short circuit (while soldering) because of small gap between conducted part and "no conducted". Maybe soldering is performed by another CNC ?
Да, всё круто! но как то в детстве, ремонтируя мопед, брат вырезал небольшую прокладку из паронита прямо из центра огромного листа. Отец увидев это, отвесил несильный упрек, и сказал, что экономить материал нужно всегда, не известно, когда он может пригодиться, и будет ли возможность его купить.
misleading video title: it should contain "expensive" as it involves the use of a commercial CNC tooling machine; a laser engraver is way cheaper and yields comparable precission and quality results
If you have a cheap 3d printer around adding a motor and small engraving bit is a prettycheap option. Should cost around ~200$ to get you the same results!
Great video, thanks a lot. The PCB is fixed by two supports only, no autoleveling used and traces milled look just perfect. Did you use spring loaded bit here? Or is the bed mounted on springs?
Assuming that the soldering of the components will be done by people (and not by a robot) the possibility of this process end up resulting in some short circuit point(s) is too great!! You should have programmed the router to remove a larger area of copper around the tracks!
Very nice and quick. What is the be-burring process? I work in aerospace and have had boards in with 'frilly' edges to the tracks. When you are trying to tune a stripline at centimetre wavelengths it is a nuisance when bits fall off the strip and shift the frequency.
I don't know if there is a chance that a layout made this way could have errors, like short-circuit. If so, another neat feature would be a automatic check. The information is there, the functionality would need to be programmed in.
You can use a presensitized pcb and with some test about uv timing u can have very good results I had successfully made a double sided pcb at home for a flight controller with clearence 0.1mm between traces and pads and all its components is smd. U still need to heat the etching acid so use boiled water and u will be ok I even covered it with a uv solder mask and make a screen printing for the components using a silk screen with white color uv solder mask
@@MrfB-br6yh Thanks for that info! I'll look into that for the next time I make something. I bet it looks really nice and neat and professional. Thanks again🙏
El nombre correcto sería , después de 1 año de práctica los PCB en 11 min con la herramienta y conocimientos adecuados , excelente video , me encantó lo profesional , felicidades
Does that mean, the parts of the copper that were etched out, are now isolated from the rest of the copper sheet? That way you don't get a short circuit?
What would be the right price for such machine for hobbyists? How much would you be willing to pay for it considering that it could save you weeks in waiting times for a high quality pcb?
@@isusek1234 you can but is a lot harder than using a cnc. And old what the guy above is saying that it expensive, you can fine cheap ones online for $100-200 that can do the fine copper work
@@merunasgЗа эти недели ожидания вы получите набор из нескольких досок, которые просверлены, покрыты припоем и закрашены маской. И здесь вам еще предстоит это сделать. Но для прототипов полезно, если у вас богатый папа, или вы получили грант на создание прекрасного видео на RUclips.
Уверен что скорость на видео завышена (тонкие фрезы и граверы, на такой скорости долго не проживут). Пыль сдувается - для здоровья не полезно (Дышать стеклянной микро-пылью от стеклотекстолита). Заявленная точность - это точность позиционирования в идеальных условиях (на практике, при заданной точности и показанной скорости тонкая фреза начнет изгибаться). Красивая демка и не больше. Музыкальное сопровождение - скрыть шум в процессе работы, и скрыть реальную скорость. Где вы видели идеальный текстолит? в реальности на плате перепад толщины (плюс коробление - отклонение листа от идеальной плоскости) может достигать 0,5мм. В итоге или дополнительное время на сканирование высоты поверхности платы (соизмеримое с временем фрезеровки) или увеличенная глубина на проходе (посчитайте сам на сколько увеличится ширина реза у гравера 30 градусов при заглублении для гарантированного прорезания фольги. Ну и вишенка на торте: если использовать такие тонкие зазоры - 1. Небольшое повреждение фольги (заусеница при фрезеровании или случайное ударное (или надавливанием) замятие твердым предметом позже может вызвать короткое замыкание. 2. При пайке капелька олова может коротнуть и найти проблемное место не всегда будет просто. Увеличение же зазоров приведет либо к увеличению времени, либо к значительному ухудшению точности.
А зачем тебе realtime?? Главное - чтобы на выходе была идеальная плата, которая безгеморно пилится хотя бы за час. А все эти ЛУТы - голь постсоветская.
@@daitedve1984 идеальная плата - это правильно луженая плата с маской и маркировкой. За час получится только профрезеровать зазоры в небольшой платке. Это вы называете идеалом? На jlcpcb за примерно 6€ (с доставкой) можно получить 5 кв дециметров отличных двустронних плат. Считаем примерно 3800/6 получается за стоимость станка можно получить более 600 типов плат отличного качества. Фрезеровка - только для прототипов которые нужны "вчера".
With the right bits and low enough lateral cutting speeds, it works. Honestly, at that kind of spacing, soldering issues and bridging are more of a problem than the cutout of the traces.
@@Champignon666 CNC mills are expensive. If you really want to make your own PCBs try a laser engraver + etching: ruclips.net/video/1hFNj86L7sk/видео.htmlm5s And with some more improvements: ruclips.net/video/ZzO9skEYqwY/видео.html
Vasyl, that is the PCB. This is a negative process, removing the copper between the traces. The cuts open the gaps between the traces down to the backer and leave the traces. It looks unusual to anyone who is used to etching their boards, because they expect to see the copper removed from all the large areas surrounding the active traces, but this technique leaves the unused copper instead.
@@becketthor I guess it could be used as a positive photoresist mask, as long as your light source was strong enough to pass through the PCB backer and the backer had no labeling on it, but that would be a waste, since you have a fully processed PCB at the end of this cutting, ready to be cleaned and soldered.
Total flipping on this process. Before was you ink out the connections. Drop in acid and dissolve all the metal off the board. Now no mess and no acid messing around. Absolute brilliant.
Very expensive precision engraving machine .Software cost ? The copper-plated-Laminate-bakelite Plate cost per square cm ? Is it possible to Replace the present PCB manufacturing process ?? Good idea with simple process without any chemical processing such ad etching,UV,plasma, +- light harden/remover material,. ..etc
@@chaos.corner As long as you know what codes it uses for which functions and have at least one file for header info, another gcode generator could probably be set up to work with it. The problem is with companies who try to make a closed ecosystem of products, only to leave their software massively vulnerable. Most browsers can't tell the difference between a local html file and a live site, if a web app is really that much easier to implement.
@@c4pt1n54no I agree. GCODE is well understood so someone could definitely create a similar app if they haven't already. I don't know if this site is even affiliated with the machine producer. I appreciate when people create sites like this but they absolutely cannot be relied on. I would avoid buying something that required online access as part of its workflow (unless that was essential to its activity). Edit: Even worse, the site appears to be run by a competitor. Imagine if they decided to mess with this company and suddenly require a login (available only to carbide3d machine owners) to access the site.
nobody use such big places for soldering and holes (its just show of how cool this product is, but its no real use case). Show us holes 0.8 mm and places of 1.5 and don't forget for soldering mask removal with spring loaded tool. This machine is expensive with no reason. Every other CNC can do the same saving your wallet
I downloaded the wegstr_v3.1.1.zip. and unzipped it. It produced a folder 'Samples (g-code)' which contained some GCODE files. I tried the 'PCB.txt' file in my licencensed copy of Mach3 and it worked. What code was used in this video on your cnc machine. 'Sprint-layout 6' does not seem to produce GCODE only HPGL. Is it possible to convert HPGL to GCODE?
I don't own this kind of machine , but with a lowcost one I managed to get the same best result with this method , I keep !!! ( CNC 3018 / Arduino UNO / CNC Shield V3 not the original woodpeeker )
@@dijuathomas5955 a lot more work, but doable. but yes you are trading less CNN time for more chances of a short circuit, not too bad a trade in my opinion. but he does have a video making a red solder mask
Back in 2000 as an electronics hobbyist at that time i was designing on paper and making myself the PCBs for fun, electronic door bell, small radios, cable TV amplifiers, etc using nail paint and nitric acid, and as for drilling, i was making the drills manually with a small device. Took me hours to complete something but every time in the end I was so happy that i did another working PCB without any mistakes.
kudos to you mate !!! but today it is about monetizing your projects taking on the big guns in this tough economic times
Cris33311 Прямо с языка сорвал .
Один в один!
Азотную кислоту не применял.
Хлорное железо, само собой потом:
Перекись водорода+ слабенький р-р HCl
_или медный купорос с солью.
Получалось просто зашибись.
Самое "тяжёлое"- нарисовать красиво, без " соплей"и пропусков.
И лаки, у жены украденные, и всевозможные нитрокраски- всё испробовал..
...давно это было...
А лучшего человечество и не придумало...
Кроме как травить....
Step 1: Own a CNC machine
Exactly what I was going to say
@@Pdrum2 of
It's very easy to short circuit (while soldering) because of small gap between conducted part and "no conducted". Maybe soldering is performed by another CNC ?
Step ZERO
@@sawomirsiwek7558 so you just don't know how to solder?
You guys are awesome! I am sure there are people in the galaxy who can afford $3000 PCB machine at home, to play around. Good luck!
Why placed it in the middle now you have to throw away a lot of the plate?
The system is good but too expensive for student use.
Да, всё круто! но как то в детстве, ремонтируя мопед, брат вырезал небольшую прокладку из паронита прямо из центра огромного листа. Отец увидев это, отвесил несильный упрек, и сказал, что экономить материал нужно всегда, не известно, когда он может пригодиться, и будет ли возможность его купить.
ЧПУ конечно крутой, но вот вырезать маленькую платку из середины листа, это трындец!
misleading video title: it should contain "expensive" as it involves the use of a commercial CNC tooling machine; a laser engraver is way cheaper and yields comparable precission and quality results
If you have a cheap 3d printer around adding a motor and small engraving bit is a prettycheap option. Should cost around ~200$ to get you the same results!
@@mattyd_gaming7425 Not sure 3D printer has enough strength to keep routing motor.
Only a very high power (expensive) laser engraver will cut copper clad.
Quick and easy, if you can spend $10K for the machine.
As everything on youtube and DIY things... "(¬ . ¬)"
you're looking in the wrong places then. Carbide 3D has a machine called Nomad for only 2800
Very nice, but you need to reduce the price of your machines. That is the only thing that puts me off buying or recommending one!
Great video, thanks a lot.
The PCB is fixed by two supports only, no autoleveling used and traces milled look just perfect.
Did you use spring loaded bit here? Or is the bed mounted on springs?
Assuming that the soldering of the components will be done by people (and not by a robot) the possibility of this process end up resulting in some short circuit point(s) is too great!! You should have programmed the router to remove a larger area of copper around the tracks!
I have a desktop CNC machine that will route PCBs (with trace widths down to 8 mils), but it'll also cut parts out of aluminum.
Hi 👋 , I also have the same😅, let's connect? OddlyIncredible
What about a few videos on the machine itself and the software. How do you get other PCB package designs into the CNC?
So easy when you have a cnc at home haha
That's what I was going to say, it's a piece of cake to make PCBs with the 'right tools', aka 'expensive tools'
Check Root CNC project
U can use just permanent marker and FeCl3, ugly, but cheap and it work
Так цей станок не дорого коштує, чому ти смієшся? Я живу в Україні, маю маленьку зарплатню і то можу собі дозволити купити такий станок
Which software' tool can you use
I was in some kind of hypnotic trance watching this. very cool
Very nice and quick. What is the be-burring process? I work in aerospace and have had boards in with 'frilly' edges to the tracks. When you are trying to tune a stripline at centimetre wavelengths it is a nuisance when bits fall off the strip and shift the frequency.
I found frilly edges can be removed with a hard plastic bristle brush, or brass brush.
I really appreciate you sharing this. It was enjoyable to watch and I got insight on one of my own projects. Thank you!
Use a 100pin TQFP next time at least, if you want to show off with the machine.
ok no problem :)
This has to make it into one of those most satisfying video collections on youtube
I don't know if there is a chance that a layout made this way could have errors, like short-circuit. If so, another neat feature would be a automatic check. The information is there, the functionality would need to be programmed in.
So satisfying to watch. Wish I had one of those machines. Hand etching a circuit layout takes longer.
You can use a presensitized pcb and with some test about uv timing u can have very good results
I had successfully made a double sided pcb at home for a flight controller with clearence 0.1mm between traces and pads and all its components is smd.
U still need to heat the etching acid so use boiled water and u will be ok
I even covered it with a uv solder mask and make a screen printing for the components using a silk screen with white color uv solder mask
@@MrfB-br6yh Thanks for that info! I'll look into that for the next time I make something. I bet it looks really nice and neat and professional. Thanks again🙏
@@SSGSativa welcome any time every time
Meu amigo, é possível fazer A usinagem De uma PCB pra um patricinâmetro de membrana soft pot?
Whoever chooses the music for these videos needs a raise.
what is program name?
Buenos días desde México, como se llama la primera broca que usaste para las pistas
Benjamin
Tu puedes hacer ese tipo de trabajo?
Necesito hacer algunos projectos
Donde tu vives?
Toll! Werde 'die Tage' wohl erneut mein Glück mit Sprint-Layout versuchen - besten Dank für diese 'How to' Anleitung.
Please make on video how to make the machine
It's cool but I not have money To buy it
What a shame if you're programmed it right you could have gotten four Boards out of that one blank PCB board what a waste
😆
Nothing for waste, it was for video
Wow, felt so satisfying watching it mill.. great!
Guys, this is SUPER EXPENSIVE. Search on youtube for "The ANT PCB Maker". An open source PCB CNC machine.
El nombre correcto sería , después de 1 año de práctica los PCB en 11 min con la herramienta y conocimientos adecuados , excelente video , me encantó lo profesional , felicidades
Reparacion de centralitas
Tu puedes hacer ese tipo de trabajo?
Necesito hacer algunos projectos
Donde tu vives?
When I was a kid all we had was a PDP-10 and some ferrous chloride.
Does that mean, the parts of the copper that were etched out, are now isolated from the rest of the copper sheet? That way you don't get a short circuit?
Why in the middle of the board. Waste of material.
Doea this require a special pcb board or any pcb copper or foil can work?
i dont have one of these in home
How much is it cost ??? Your cnc
Which came first...
Pcb or software
Chicken
How much it's machine?
Thank God and You, something sane to watch.
Impressive. Unfortunately is still too expensive for hobbyists. Maybe in a couple more years
What would be the right price for such machine for hobbyists? How much would you be willing to pay for it considering that it could save you weeks in waiting times for a high quality pcb?
You can make pcb wihout cnc
@@isusek1234 you can but is a lot harder than using a cnc. And old what the guy above is saying that it expensive, you can fine cheap ones online for $100-200 that can do the fine copper work
@@merunasgЗа эти недели ожидания вы получите набор из нескольких досок, которые просверлены, покрыты припоем и закрашены маской. И здесь вам еще предстоит это сделать. Но для прототипов полезно, если у вас богатый папа, или вы получили грант на создание прекрасного видео на RUclips.
И прежде чем заказывать доски на заводе, вы делаете прототип на макете.
Wooow, how much it's cost?
2500€
try something solder on this kind psb
Its really difficult i have tried once and failed terribly
Уверен что скорость на видео завышена (тонкие фрезы и граверы, на такой скорости долго не проживут). Пыль сдувается - для здоровья не полезно (Дышать стеклянной микро-пылью от стеклотекстолита). Заявленная точность - это точность позиционирования в идеальных условиях (на практике, при заданной точности и показанной скорости тонкая фреза начнет изгибаться). Красивая демка и не больше. Музыкальное сопровождение - скрыть шум в процессе работы, и скрыть реальную скорость. Где вы видели идеальный текстолит? в реальности на плате перепад толщины (плюс коробление - отклонение листа от идеальной плоскости) может достигать 0,5мм. В итоге или дополнительное время на сканирование высоты поверхности платы (соизмеримое с временем фрезеровки) или увеличенная глубина на проходе (посчитайте сам на сколько увеличится ширина реза у гравера 30 градусов при заглублении для гарантированного прорезания фольги. Ну и вишенка на торте: если использовать такие тонкие зазоры - 1. Небольшое повреждение фольги (заусеница при фрезеровании или случайное ударное (или надавливанием) замятие твердым предметом позже может вызвать короткое замыкание. 2. При пайке капелька олова может коротнуть и найти проблемное место не всегда будет просто. Увеличение же зазоров приведет либо к увеличению времени, либо к значительному ухудшению точности.
а пыль точно сдувается?
можно конечно сделать заливку охлаждающей жидкостью, если переживаете. ВОобще метод хорош.
А зачем тебе realtime?? Главное - чтобы на выходе была идеальная плата, которая безгеморно пилится хотя бы за час. А все эти ЛУТы - голь постсоветская.
@@daitedve1984 идеальная плата - это правильно луженая плата с маской и маркировкой. За час получится только профрезеровать зазоры в небольшой платке. Это вы называете идеалом? На jlcpcb за примерно 6€ (с доставкой) можно получить 5 кв дециметров отличных двустронних плат. Считаем примерно 3800/6 получается за стоимость станка можно получить более 600 типов плат отличного качества. Фрезеровка - только для прототипов которые нужны "вчера".
без лака, маски, металлизации, лужения это не плата, это фуфло.
а еще не помешало бы массу пустить на изолированные участки, раз уж они оставлены.
Which softwares did you used in video?
Как-то не рационально с такого куска текстолита вырезать такую маленькую плату. Там 4 можно сделать
Это для видео жееее)
o si explotemos
А плоттером по композита Вас не удивило?
зато каких крутых соплей из олова можно навесить
Carbide Copper incorrectly opens the gerber.
All the lines are much thicker than in the source file, the lines just merge.
It's not a pcb, it's a cnccb.
do you have a link for the bits you are using?
Yes, see this wegstr.com/30%C2%B0-spiral-carbide-engraving-bit
With the music it was mesmerising
what soft ware use for PCB design?
Nice machine. Not going to spend that kind of money though.
Great I would like to learn that.but in that plate you can make 4 of this pcs right?
looks cool for hobbyist, but for 2400 € ?.. a bit high price if you ask me :(
A 3d printer could be converted if you have the skills. Someone needs to put together conversion kits, they would make bank.
So this would be a R & D step before mass production?
yep, literally definiton of a prototype
Beautiful and totally mesmerising but..... bridging seems more than just possible.
J S not impossible. Wire on non-copper side or 0ohm resistor
@@Electheo hey no..
He said about unintended bridging
Greatest! What name is CNC?
Great. Let's see it do traces for a 128-pin QFN IC
With the right bits and low enough lateral cutting speeds, it works. Honestly, at that kind of spacing, soldering issues and bridging are more of a problem than the cutout of the traces.
how much is the maintenance cost?😁
That is a really clean cut!!!
Как называется фрезерный станок и сколько стоит он ?
Это авторский станок, стоит 2килобакса)
i can watch forever that machine drawing board texture
What about double sided?
Flip the PCB upside down, set the origin and follow the same procedures shown in the video i guess
Nice machine but 1,790.0 € is way too expensive for any hobbyist.
do you know a more affordable machine?
@@Champignon666
CNC mills are expensive. If you really want to make your own PCBs try a laser engraver + etching:
ruclips.net/video/1hFNj86L7sk/видео.htmlm5s
And with some more improvements:
ruclips.net/video/ZzO9skEYqwY/видео.html
hi how much cost me to make a old amplifier pcb and mail it to me ????? just one
if you're still searching, JLCPCB seems to make good quality pcbs for little money, but shipping is like $15
@@tobbleboii5988 thanks
Máš to pěkně udělané. Podle toho videa to vypadá že bych to zvládl i já.
It's great!
Is that equipment homemade or not?
blow away FR4 dust is not very good idea ! ...
Hi Buddy... may you tell me the software's name and to describe the tools used in this project ?
взял бы лучше лист метр на метр и по центру тоже плату вырезал
@Kriso Sborshik да все ради ебаных просмотров. полезное то все уже сделано, а снимать что то надо. современный мусор - информационный мусор
Why etch when you can cnc? Good
олигарх , где такой станок взял? С таким то станком я бы то же за 11 минут забацал.
Nice job, but what about labeling components and the clear coat.
How to build a car:
Step 1: Own a car manufacturing plant.
Perfect job!! 30° - carbide engraving bit - what diameter? 0.2 or 0.1?
Why does this have 2m views
Did youtube recommend it to everyone
Hello man, what is the thickness of the pcb board?
It's not matter
Satisfying to watch
Sir how i can get these training ...
So, where is PCB? It's a drawing with holes.
It's used to silkscreen solder resist
Vasyl, that is the PCB. This is a negative process, removing the copper between the traces. The cuts open the gaps between the traces down to the backer and leave the traces. It looks unusual to anyone who is used to etching their boards, because they expect to see the copper removed from all the large areas surrounding the active traces, but this technique leaves the unused copper instead.
@@becketthor I guess it could be used as a positive photoresist mask, as long as your light source was strong enough to pass through the PCB backer and the backer had no labeling on it, but that would be a waste, since you have a fully processed PCB at the end of this cutting, ready to be cleaned and soldered.
tools durability ???
Just a joy to watch 😀
Total flipping on this process. Before was you ink out the connections. Drop in acid and dissolve all the metal off the board. Now no mess and no acid messing around. Absolute brilliant.
Very expensive precision engraving machine .Software cost ? The copper-plated-Laminate-bakelite Plate cost per square cm ? Is it possible to Replace the present PCB manufacturing process ?? Good idea with simple process without any chemical processing such ad etching,UV,plasma, +- light harden/remover material,. ..etc
Online app for gcode? So I have to pay to get the machine, and I have to pay for internet just to use it...
Just wait until the website goes down for good. I have to assume there's some local application that can do the same thing?
@@chaos.corner As long as you know what codes it uses for which functions and have at least one file for header info, another gcode generator could probably be set up to work with it. The problem is with companies who try to make a closed ecosystem of products, only to leave their software massively vulnerable. Most browsers can't tell the difference between a local html file and a live site, if a web app is really that much easier to implement.
@@c4pt1n54no I agree. GCODE is well understood so someone could definitely create a similar app if they haven't already. I don't know if this site is even affiliated with the machine producer. I appreciate when people create sites like this but they absolutely cannot be relied on. I would avoid buying something that required online access as part of its workflow (unless that was essential to its activity).
Edit: Even worse, the site appears to be run by a competitor. Imagine if they decided to mess with this company and suddenly require a login (available only to carbide3d machine owners) to access the site.
nobody use such big places for soldering and holes (its just show of how cool this product is, but its no real use case). Show us holes 0.8 mm and places of 1.5 and don't forget for soldering mask removal with spring loaded tool. This machine is expensive with no reason. Every other CNC can do the same saving your wallet
@WEGSTR CNC pls, tell me what is the music in this video? I tried to use shazam but failed =( NEED THIS MUSIC for my mind
agree. it's intense.
Excellent job but...to expensive for a PCB... sorry.
What circuit desing you
Nice product! But a lot of pcb material was wasted, can this be prevented?
I'm guessing you could use a smaller pcb black, adjust your outlines, or move the zero point to minimize the waste.
@@Razzman70 moving the zero point seems like the best option
I downloaded the wegstr_v3.1.1.zip. and unzipped it. It produced a folder 'Samples (g-code)' which contained some GCODE files. I tried the 'PCB.txt' file in my licencensed copy of Mach3 and it worked. What code was used in this video on your cnc machine. 'Sprint-layout 6' does not seem to produce GCODE only HPGL. Is it possible to convert HPGL to GCODE?
Super! But price.... (((
what is the part number vb of this machine.what is the maximum size of PCB which can be made from this machine
I don't know what is making but the music sounds nice.
Does someone buy this machine? Could you tell me your experience with it?
I don't own this kind of machine , but with a lowcost one I managed to get the same best result with this method , I keep !!! ( CNC 3018 / Arduino UNO / CNC Shield V3 not the original woodpeeker )
@@MC909Garfield Tu puedes hacer ese tipo de trabajo?
Donde tu vives?
O Cristian
Tu puedes hacer ese tipo de trabajo?
Donde tu vives?
There is more chance of short circuit soldiering, bcz you are not removing unwanted copper part
That can be verified with a quick continuity check using a multi meter
using a small 1.2D tip and inspecting the solder joints being power up (and ohms check) should be sufficient
@@keithforbes2326 what about a bigger circuits
@@dijuathomas5955 a lot more work, but doable. but yes you are trading less CNN time for more chances of a short circuit, not too bad a trade in my opinion. but he does have a video making a red solder mask
Muy bueno. Donde lo consigo??
Wilson
Tu puedes hacer ese tipo de trabajo?
Donde tu vives?