Cool, I'm putting a 196.3×81.7mm waveguide antenna right now with a little bit of an experimental ground reference plane. Just need to cut and attach the front of the guide, but so far everything matches the nominal layout to a tolerance smaller than my eyes can resolve so I'm excited about this one. I've also ordered some short path connectors so I can cut the signal path from the reciever to the modem down to the lenght of the actual element, and usb can handle the signal from there as it works without percieved loss. My setup is for 2.437Ghz or chan 6 (us).
This works well with the indoor coaxial nodes tied perpendicular to each other and placed beneath my phone. Now, is there any way to create indoor unit to broadcast signals wirelessly indoors..?
you actually created a short on your yagi. The 2nd large disk needs to be isolated from the main nut and screw going through it. This will greatly increase your signal. you can use plastic or duct tape to create that shielding.
Hey guys, I'd like to know how you came up with the dimensions for these antennas? Did you used some software calculator or some formulas? I would like to know as I am going to make an antenna with specific frequency for my 4G LTE provider.
Ok, now I will feel free to ask. Should you have continuity between inner and outer part of coaxial cable? Because in a way how it looks from video, ground shield and central pin are connected to a 2 different disks, but through the middle they are all on same shaft!?
Could you please let me know the setup configuration for 2300MHz for 4G signal. You have awesome knowledge of network and I really really love it. Keep making these type of videos. Thank you.
Could you use one of these antenna designs to make a drone-Killing Kalashnikov Gun? Basically send enough signal out at a drone operating frequency to make it lose contact with its pilot?
You need to isolate tye driven element i.e 2nd largest disc from all the others discs , otherwise your vswr will be veey high , yes itll work with low power but u can damage your router , simply insulate tue driven element and its very important u do this as its not covered in this video
I'm from a vilage that so far from my town. No internet connection in my vilage. Thanks for your show. I want to make my own boster. Can you show clearly me all of spesification of materials?
Looks like a good idea, some of those speeds are faster than what i am getting although I am paying for the lower speed so that is fair enough. I liked the clock in the background it reminded me of one of those Radium painted dials.
@@chrisshr5383 hola! No papá, cuando la crisis de la cuarentena el que era jefe mío trajo varios amplificadores de señal y le compré uno que servía para Digitel, funcionó hasta cierto punto pero el aparato que amplifica como tal que es el que va en la casa se apagó y no prendió más, tengo que abrirlo y ver si fue que se desoldó algo
thank you from venezuela, I will try to make one to see how I achieve it, because here the most common materials are not achieved, and if you get them, they are too expensive, but thanks for the plan and the idea
this is the first time for me to comment on youtube video but this one really deserve, i built this antenna it is really brilliant, it made the signal strenght always 75% instead of 25% or 50% using normal router antenna, i am just wondering how can i improve more in the antenna so that i can get 100% signal strength 1- i used RG-6 coaxial cable "length isno exceeding 12 meters" 2- if we used more than one antenna will it help ?
The last two circle (the circle where wires are connected) have contact with each other which is not good the wifi or 3g card. it can fry the chip inside them
Nah, the dishes have capacitance and the bolt has some inductance, and then there is the phase shift for the extra distance the signal has to travel from one point to the other. Certainly, we're not in DC-land anymore! In short, to really damage the card, you need to be very unlucky. You need either a perfect short-circuit, open connection, or a pure imaginary load (ideal capacitor or inductor) at the end of the coax cable. Then you need to have the coax be a very specific length depending on what the load is.
Could you use a longer cable if you bought some of that expensive type with low impedance for higher frequencies? Because I know standard RG6/59 has pretty high impedance in the gigahertz range.
hi, thanks for this video. I can't understand one thing: how do you connect sat cable with sma connector? are you using some adapters? if yes how is this adapters? Thank you :)
Difficult to believe with just an antenna to get very high signal...even with an amplifier booster it would only increase just average...the point with weak signal is even a slight of wind can change the intensity..if you are only using antenna....or with additional of booster it will stabilize the signal consistently
Wow.it's really work, Here at the Philippines my Speed test is 1mbps only and then I decided to create this one my Speed test now is 364mbps that's how it's works
Can you make 4 Guns simultaneous and orient them to the 4 cardinal points? I think it will cover most signals for 12 km radius, and you will have signal from any direction, or will it interfere with each other?
do you think it would make any sense to use this in the deep woodlands, where i cannot set it above the treetops (i have some signal but its too weak)?
Hello guys, you did a very nice job. I'll do this antenna on my dacha in carpathian mountains in Poland this summer because of weak signal. Can I ask you how tick is this copper plate?
![BLACK BAG - Official Trailer [HD] - Only in Theaters March 14](http://i.ytimg.com/vi/Du0Xp8WX_7I/mqdefault.jpg)
I built this 4G gun myself. I can't believe it actually work. Thank you from America!
Every body gangsta until the USSR engineer gets better speeds with a custom made antenna and a *3g* sim than your ADSL.
It's a strange feeling to watch someone have such a firm grasp of the engineering topics that are my weakest points.
You guys are the best!
Much more details than the previous GUN
Awesome videos dude! You are very smart and inspirational. The world needs more people like you.
I did this and really got improved for 4g lte speed from 30mbps to 60mbps. thank you sir.
imagine being friend with this guy and you can visit him daily? I wouldn't miss a day
Literally rewatched the first wifi gun videos yesterday, lol
I've never seen any 3G connections work faster like this! Thanks for demonstrating.
the voice over is insanely fun!
Well done guys, this should silence your doubters. ...........Kreosan 10.....doubters 0. Much better video this time. Keep up the good work..😎
Also use 50 ohm cable good quality keep lengths as short as possible and use 50 ohm connectors as tv n satellite are all 75ohm , lte is 50 ohm
Cool, I'm putting a 196.3×81.7mm waveguide antenna right now with a little bit of an experimental ground reference plane. Just need to cut and attach the front of the guide, but so far everything matches the nominal layout to a tolerance smaller than my eyes can resolve so I'm excited about this one. I've also ordered some short path connectors so I can cut the signal path from the reciever to the modem down to the lenght of the actual element, and usb can handle the signal from there as it works without percieved loss. My setup is for 2.437Ghz or chan 6 (us).
This works well with the indoor coaxial nodes tied perpendicular to each other and placed beneath my phone. Now, is there any way to create indoor unit to broadcast signals wirelessly indoors..?
like, the unsheilded ends of the cable from the gun?
you actually created a short on your yagi. The 2nd large disk needs to be isolated from the main nut and screw going through it. This will greatly increase your signal. you can use plastic or duct tape to create that shielding.
THANK YOU SO MUCH, I WAS SO CONFUSED BY THIS!
Hey guys, I'd like to know how you came up with the dimensions for these antennas? Did you used some software calculator or some formulas? I would like to know as I am going to make an antenna with specific frequency for my 4G LTE provider.
There's schematics online.
The formula is
Lightspeed / TargetFrequency = Wavelength
the diameter has to be half of the wavelength you want to produce/emit/receive
You're awsome! Greetings from Poland
Właśnie jestem na wiochy i mam beznadziejnie z netem haha.
Thanks! I finally can communicate with my family back home in Andromeda
Stolen
Is it work really?
That's insane! I should really try doing this myself, I have -100dB normally.
-100 dB is equivalent to -70 dBm, so that's not too bad actually
have you made this antenna
the second disk, the supplier, needs to be insulated from the rest. If you put on amp it will blow amp.
Ok, now I will feel free to ask. Should you have continuity between inner and outer part of coaxial cable?
Because in a way how it looks from video, ground shield and central pin are connected to a 2 different disks, but through the middle they are all on same shaft!?
very interesting.
Is it better the
threaded rod is made from metall or plastic?
this vid inspire me to create same antenna from pcb board because in my region hard finding those copper sheet
thanks a lot
You guys are honestly the best ducking thing on the internet
5:50 somebody know name this app for phone?
netmonitor
Could you please let me know the setup configuration for 2300MHz for 4G signal.
You have awesome knowledge of network and I really really love it.
Keep making these type of videos.
Thank you.
0:33 Can i use any kind of metal sheet?
Well, gold, copper, zinc work best
There's the braided wire and the solid wire. You connect braided wire to the biggest disc and the solid to the second one?
Thank you sir. 100% working. Good job sir. God bless you.
bhai did u try
Could you use one of these antenna designs to make a drone-Killing Kalashnikov Gun? Basically send enough signal out at a drone operating frequency to make it lose contact with its pilot?
Michael Pierce YOU BAD SOB ...I WOULD LIKE TO KNOW HOW TO MAKE THE TRANSMITTER AS WELL....5G IS THE BRAIN LIQUIDISER
Dorrien North one may wish to research electrostatics for blocking such signals. Pretty sure we'll see someone's going to try microwaving the world.
That would be called jamming... dji has a product like this to bring down their own drones over restricted airspace
RCP-1136 that isn't jamming, that is a backdoor
Nope, that's jamming.
where can I find the measurements needed for making a 4G gun for Band 40 (2300MHz)? This is what my provider runs off
Why are you shorting the primary element to ground? It should be isolated!
The reflector and directors should be OK grounded but the primary?
hey how to made your smoke bulb? its fantastic
You need to isolate tye driven element i.e 2nd largest disc from all the others discs , otherwise your vswr will be veey high , yes itll work with low power but u can damage your router , simply insulate tue driven element and its very important u do this as its not covered in this video
El segundo disco al que te refieres, sería el disco de mayor diámetro de entre los 6 que tiene esta antena?
I'm from a vilage that so far from my town. No internet connection in my vilage.
Thanks for your show. I want to make my own boster. Can you show clearly me all of spesification of materials?
it is fake, do not even think about it
Aloy Ngoran i suggest to buy a 4g antenna omnidirectional it’s just easier and cheap
Saludos quisiera saber si pudiste tener señal con esas antenas?
Looks like a good idea, some of those speeds are faster than what i am getting although I am paying for the lower speed so that is fair enough. I liked the clock in the background it reminded me of one of those Radium painted dials.
NICE antennae!... but that truck stole the show!!
хорошие антенны! Но грузовик украл шоу
Megabites are not mbps, from bits to bites you have to divide it by 8. Greets
Sir, do the two copper plates touch the bolts? 🤔
nice work, but the first and second disks are connected by the rod, isn't that shorting the connector end points?
Hi, does it have to be two cables? And the other pole definitely uses us, that is, the sows.
Hi, does it have to be two cables? and the other pole is definitely not used, that is, the sow one?
Will thickness of copper sheet won't matter? Thanks.
Which app you used to find the tower location
netmonitor
Can you show how we can attach a diy amplifier to it?
Hello! What could be the requirements for making the antenna for 3G 900Mhz and 4G B3 1800Mhz? Nice job! Greetings from Venezuela?
¡Amigo!
¿Lograste fabricar alguna antena similar de prueba para Venezuela?
¿Que tal te fue?
¡Gracias y saludos!
@@chrisshr5383 hola! No papá, cuando la crisis de la cuarentena el que era jefe mío trajo varios amplificadores de señal y le compré uno que servía para Digitel, funcionó hasta cierto punto pero el aparato que amplifica como tal que es el que va en la casa se apagó y no prendió más, tengo que abrirlo y ver si fue que se desoldó algo
@@thehead85 ¡Ah okey hermano que mal!
¿Que material es el que usa el ING en el video?
Parece algo así como láminas de cobre
@@chrisshr5383 me puse a ver el video de nuevo y se refiere al material como "foil", creo que es aluminio... Si lo llegas a replicar avísame!
Can I use this antenna outdoor and indoor with repeater or without repeater in basement for mobile network?
Some of the best inventions are built out of necessity.
5:48 what app is that ?
can anyone here tell me the name of the application he uses in his phone
im also interested!
you are awesome dude, greetings from Canada.
thank you from venezuela, I will try to make one to see how I achieve it, because here the most common materials are not achieved, and if you get them, they are too expensive, but thanks for the plan and the idea
Hola, ya lo intentaste ?
Really nice. What’s the name of the two little conectora on the USB modem ? Thanks
this is the first time for me to comment on youtube video but this one really deserve, i built this antenna it is really brilliant,
it made the signal strenght always 75% instead of 25% or 50% using normal router antenna, i am just wondering how can i improve more in the antenna so that i can get 100% signal strength
1- i used RG-6 coaxial cable "length isno exceeding 12 meters"
2- if we used more than one antenna will it help ?
Why is your driven element not uncoupled from the other elements? Element 6 on the drawing.
you guys really are the best
The last two circle (the circle where wires are connected) have contact with each other which is not good the wifi or 3g card. it can fry the chip inside them
I just looked it up - seems it's a kind of yagi antenna with gamma match - if measurements are correct it should be fine I guess...
Nah, the dishes have capacitance and the bolt has some inductance, and then there is the phase shift for the extra distance the signal has to travel from one point to the other. Certainly, we're not in DC-land anymore!
In short, to really damage the card, you need to be very unlucky. You need either a perfect short-circuit, open connection, or a pure imaginary load (ideal capacitor or inductor) at the end of the coax cable. Then you need to have the coax be a very specific length depending on what the load is.
have you made this anntena
usama khan yes. but after month of use . my wifi alpha card has burned.
i need some help do you have whatsapp num or facebook id whrer we can disscuss it
Nice video, btw can you give me a design and dimension for 4G LTE band 3 (1800MHz) of the 4G gun thankyou !
Very nice video.
What is the name of antenna.
How do you calculate this is there any formula.
Pls let me know.
10/10 Teen Spirit
hola
Você pode mandar as medidas para 850 MHz?
You are wonderful, dear teacher. Please include the method of making the 3600 signal booster antenna.🙏❤️🌹
Great videos guys keep them coming.
This is really helpful. Could you please mention the dimensions for 1800Mhz. Thank you
Could you use a longer cable if you bought some of that expensive type with low impedance for higher frequencies? Because I know standard RG6/59 has pretty high impedance in the gigahertz range.
I'd love seeing the calculations behind it; great Video
hi, thanks for this video. I can't understand one thing:
how do you connect sat cable with sma connector? are you using some adapters? if yes how is this adapters? Thank you :)
Hello , I just want to know if we can use different metal sheets other than copper for this project and if we'l get similar results. Please reply
what app did you use to see all the base stations on the map?? Nice video anyway! :)
netmonitor
Can we use any type of metal stick in place of Thread stud or not?
Great video. What is the type of antenna used here?
Need a network gun for mobile try doing a vedio on that i will be glad to see you in next vedii
Any issues in strome and lighting conditions, because my area there is more lighting issue.
Difficult to believe with just an antenna to get very high signal...even with an amplifier booster it would only increase just average...the point with weak signal is even a slight of wind can change the intensity..if you are only using antenna....or with additional of booster it will stabilize the signal consistently
1:10 can you tell what is the diameter of those plates 100 what? mm cm inches??
mm
Can I make using aluminum foil?
No I'm trying it with copper foil that's a little thinner than what he has and it's a big pane I can't imagine using aluminium foil
Typical the network I'm using 4G on runs on 1.8ghz. Anyone know a calculator for such an antenna for the elements ?
Hello friend,
I have the same issue, did you find a calculator?
6:45 it is megabits, not megabytes
All discs connected to metal rod. Due to this all discs shorted to each other. Can we put insulation in each plate.
Wow.it's really work, Here at the Philippines my Speed test is 1mbps only and then I decided to create this one my Speed test now is 364mbps that's how it's works
Max scheler... madali lng po gawin? Globe o smart po kayo?
Watch carefully
i doubt, the maximum speed of 4g is 60mbps. Achieving 300 mbps is only done in a controlled laboratory
Kailangan pa ba iinsulate yung sa gitna??
Do you half to use TV/internet wire or will any wire work ?
Does the max 10meters antenna cable length apply here?
Can you make 4 Guns simultaneous and orient them to the 4 cardinal points? I think it will cover most signals for 12 km radius, and you will have signal from any direction, or will it interfere with each other?
muito boa a sua antena parabens aquii no brasil nao vi um video tao bom
Awesome. There should also be a wire for lightning for stormy weather. Thanks
You should insulate the mounting bolt and nuts between the plates.
Kemah demo... mmg terbaik la...
can you teach us the computation of that antenna that have made?
Thank you bro
hey i love ur idea but is it work only by coper
do you think it would make any sense to use this in the deep woodlands, where i cannot set it above the treetops (i have some signal but its too weak)?
Hello guys, you did a very nice job. I'll do this antenna on my dacha in carpathian mountains in Poland this summer because of weak signal. Can I ask you how tick is this copper plate?
*I think I should call* *_ELECTROBOOM_* *you know he's finding you for so long to give you a reward!!!!!!!*
i was just about to send this video link to electroBoom x-D
Great video and thanks for that app for easily locating your network towers.
I know you can do a 5g gun! 🤗That would be awesome
Can i use aluminium..? To do this?? Thx
Please can you tell which app to use to find all the information needed for this project
Hi please can you give us the design of the 1800 ghz 4g ?!?
It is in the video, watch carefuly
Please inform me what apps you are using for cell location etc..
Can you please make a diy Repeater for this antenna
Can we use plastic rod instead of metal rod