-- Helpful for the Winter Beast (04 Tahoe) thanks. Just swapped in LED, Hi-Beams, Standards, and Runnings. My driver's side Standard was practical joke high - higher than the hi-beam. Easy when you know just what you're doing. Thanks for the help. Thing isn't cross-eyed anymore either :)
You know I knew how to take them off and replace them with led but I couldn’t find out how to get them aligned I been running two dog lights with a spot/flood led so I at can see the road my headlights are up but this video now helped my out. Can I stop having to turn them off at night when ther a another car coming ps while they are off so they do t blind the other driver you can barely see anything all there is a bit of lightning but you can def see where the headlight are pointed
Is there a way to adjust each individual beams? my driver side high beam has a a wide spot and the passenger high beam has a smaller dot on it. I'm not exactly sure why that is.
Nice video. I’ve tried adjusting mine and I can’t get them to adjust hight enough at all. I cranked them all the way up and tried in and out and I still can’t get it right. Any advice?
All I wanted to know was which way to turn it to make it go down and which way to turn it to make it go out or in. This video is entirely too long. It could be summed up in 15 seconds. “Inside one goes left and right turn it left to go left. Turn it right to go right the outside one goes up and down. Turn it right to go up and left to go down“ end of video
-- Helpful for the Winter Beast (04 Tahoe) thanks. Just swapped in LED, Hi-Beams, Standards, and Runnings. My driver's side Standard was practical joke high - higher than the hi-beam. Easy when you know just what you're doing. Thanks for the help. Thing isn't cross-eyed anymore either :)
Glad it helped
I used the 1/4 in socket myself, worked great!
you don't need a torx. 6 point 1/4" socket will fit the outside of the star.
ArizonaResponseSystems agreed
And less likely to strip
Lol I was looking at this trying to figure it out for 10 minutes 😩😩 I'm glad I found this video to help out
Next up, how to organize toools🤣😂. Great video man bout to throw sme leds on mine and hope I can see at night
Very clear ND concise video. Thanks.
You know I knew how to take them off and replace them with led but I couldn’t find out how to get them aligned I been running two dog lights with a spot/flood led so I at can see the road my headlights are up but this video now helped my out. Can I stop having to turn them off at night when ther a another car coming ps while they are off so they do t blind the other driver you can barely see anything all there is a bit of lightning but you can def see where the headlight are pointed
When you make a video of “how to adjust your headlights.”....
And one of your headlights decides to blow out lol 😂
Great video!! Too bad most other cars/trucks aren't this easy to adjust or remove the whole housing.
I've owned many vehicles over the years. These GM trucks headlights are by far the EASIEST to remove and aim
Very helpful. Thank you.
As the guy so clearly demonstrated, you should never attempt to make repairs after you’ve been drinking all day.
Is there a way to adjust each individual beams? my driver side high beam has a a wide spot and the passenger high beam has a smaller dot on it. I'm not exactly sure why that is.
No there isnt. Sounds like the inside of the ligh housings have an issue.
@@Syrus54 Got it boss, I'll look into replacing the headlights then.
Will also fit a 1/4 bit or a smaller Allen key inside the torx bit
Nice vid. Ordered some new lights and they're pointed all the way down
Mine has a big gap trying to install halo
After mark headlights dont have those adjustments. Only in and out
Nice video. I’ve tried adjusting mine and I can’t get them to adjust hight enough at all. I cranked them all the way up and tried in and out and I still can’t get it right. Any advice?
lower the rear suspension. or raise the front.
Thank you. Now I know
What happened @02:06? Why did wrench drop all the way down? Probably better to do in the early evening tho.
perfect thanks
My housing is just loose and falls out halfway the plastic bit broke
It's 2000-2006
💯🙏🏽
All I wanted to know was which way to turn it to make it go down and which way to turn it to make it go out or in. This video is entirely too long. It could be summed up in 15 seconds. “Inside one goes left and right turn it left to go left. Turn it right to go right the outside one goes up and down. Turn it right to go up and left to go down“ end of video
Youre welcome.
No tools needed to remove, only to adjust.
My shit the have that too adjust it
What a mess.
First comment 😂😂🤘
😆😆😅 thank you I was looking for a way to adjust them
Wtf is up with the music seriously?