This is what i needed to run my new a2212 10t 1400kv motors and i have no clue about why my esc was beeping and what to do even though i was giving 12v to it through adapter and pwm signal from arduino. Thank you brother, you taught me something new...
After connecting 2 motors to 2 ESCs, without knowing to remove the red wire on one side of the BEC, I connected them together to the servo controller of 1 and tested the operation for about 30 minutes?? So, only one motor worked, the other motors operated randomly, and in the end, the ESC on the motor side, which was working well, was damaged and did not work at all. When I went to RUclips, I saw a video about removing one BEC. I removed the ESCs one by one, reset them, and tested them. Of the two ESCs, only the motor side, which had been malfunctioning uncontrollably, works. When I turn on the power, the motor makes the same beeping sound that it made before starting, but even when I move the throttle, it works. The motor doesn't move at all. Is there no way to save it??
Hi, I am trying to control the ESC with a microcontroller but it is not working. It beeps indicating no input signal detected. I am using a raspberry Pi pico. I also tried connecting the power to the bec but didn't work
it used to work just fine, now i don't know why only 1 motor run after calibration but the other three after i plug the baterie and the throttle is max i hear 3 beeps but thats all, the 3 motors wont turn any solution please
Hello, I saw all of your videos I am building a hexacopter but my drone tilts to the one side I don't know what the problem is I have caliberated the esc's 4-5 times just as you told, I even tried changing motors as well I am using apm 2.8. Please help
Have you calibrated ESCs using flight controller? ruclips.net/video/jHaYAA_Km7Y/видео.html Check the motor layout and direction of rotation Also , check propellers (clockwise and counter clockwise)
if i connect my motar to the propler it is not spinning properly and if i remove the propler it is running but withen few sec it is reducing speed and stopped running please check this out
I am able to do individual PWM calibration but when I try to connect it to pixhawk and use PPM calibration it's not working. And motors keeps beeping every second
Yes You have to calibrate ESC in 2 methods for stable flight 1. Do the steps shown in video for all 4 ESCs 2. Calibration of ESCs using KK board: -Remove supply -Switch on TX and keep throttle to max -Press and hold 1st and 4th button of KK board and connect battery -you should get " throttle pass through" on screen of KK board - wait for few seconds and decrease the throttle -wait for few seconds - remove battery Note: don't remove buttons of KK until all steps are done in method 2
Salam sejahtera untukmu tuan....saya mempunyai esc simonk 30a seperti yg anda punya.....ada permasalahan dengan esc saya .kenapa esc saya berbunyi beep putus2 tidak henti2.mohon solusinya
@@techathome terima kasih atas perhatiannya Permasalahannya karena saya pemula dan belum faham dengan rc plane. Kebetulan saya merakit diy rc plane arduino. Jasi permasalahan diatas sudah selesa.trima kasih banyak.i
If ESC is not working, then also this might happen, You have to check the same motor with different ESC Also have you done the connection as shown in the video?
This is what i needed to run my new a2212 10t 1400kv motors and i have no clue about why my esc was beeping and what to do even though i was giving 12v to it through adapter and pwm signal from arduino. Thank you brother, you taught me something new...
Welcome ❤️
After connecting 2 motors to 2 ESCs, without knowing to remove the red wire on one side of the BEC, I connected them together to the servo controller of 1 and tested the operation for about 30 minutes?? So, only one motor worked, the other motors operated randomly, and in the end, the ESC on the motor side, which was working well, was damaged and did not work at all. When I went to RUclips, I saw a video about removing one BEC. I removed the ESCs one by one, reset them, and tested them. Of the two ESCs, only the motor side, which had been malfunctioning uncontrollably, works. When I turn on the power, the motor makes the same beeping sound that it made before starting, but even when I move the throttle, it works. The motor doesn't move at all. Is there no way to save it??
Thank You! This fixed my non running motor :)
Welcome!
Hi, I am trying to control the ESC with a microcontroller but it is not working. It beeps indicating no input signal detected. I am using a raspberry Pi pico. I also tried connecting the power to the bec but didn't work
How I can find it even though I am not using any other flights mode except stablize
When I increase the power the motor is disconnected and again connected... 😬😬😬 What to I do
Most probably your battery is dead. Check voltages of each cell of battery with multimeter check If either cell is below 3v .
it used to work just fine, now i don't know why only 1 motor run after calibration but the other three after i plug the baterie and the throttle is max i hear 3 beeps but thats all, the 3 motors wont turn any solution please
Calibrate your ESC one after the other.
@@Techzino1 true, that was the problem indeed but i fixed it back then and graduated with the project haha thanks for the helpgreat content!
Which version of mission planner is best for apm2.8 ? 1.3.49 and latest version are not working
Try this: firmware.ardupilot.org/Tools/MissionPlanner/archive/MissionPlanner-1.3.68.msi
Then which version working fine? Please tell
Download this: firmware.ardupilot.org/Tools/MissionPlanner/archive/MissionPlanner-1.3.68.msi
My own is actually that all are spinning except 1 on the drone. What could be done?
This may be what I need. Thank you brother
Welcome
Hello,
I saw all of your videos
I am building a hexacopter
but my drone tilts to the one side
I don't know what the problem is
I have caliberated the esc's 4-5 times just as you told, I even tried changing motors as well
I am using apm 2.8.
Please help
Have you calibrated ESCs using flight controller? ruclips.net/video/jHaYAA_Km7Y/видео.html
Check the motor layout and direction of rotation
Also , check propellers (clockwise and counter clockwise)
Try recalibrating your compass again.
switch to d shot esc
hi, i did all the calibration, when i fly the drone, its did not stay in a position although i did not move it.
I have given the motor layout in this tutorial,
You can check once : ruclips.net/video/S7VZ796W8VA/видео.html
if i connect my motar to the propler it is not spinning properly and if i remove the propler it is running but withen few sec it is reducing speed and stopped running please check this out
ESC might be having issues. If possible change ESC and confirm motor is working properly or not.
How did you manage to bind the receiver with the radio with this tx on the radio screen, mine only binds with the AFHDS 2A in off teach me there
Binding TX and RX(flysky fsi6) : ruclips.net/video/AGNz5fPVBhA/видео.html
@@techathome No you don't understand, give me your WhatsApp contact I'll explain it better with photos
Bro my bldc motor not running but its beeping sound what is the problem??
I think ESC Problem.
I am able to do individual PWM calibration but when I try to connect it to pixhawk and use PPM calibration it's not working. And motors keeps beeping every second
Can you check this once : ruclips.net/video/P-HbV_d7dIU/видео.html
Befor calibration,is receiver should be bind with remote fsi6
Yes, it should be binded.
Is this process same for kk2.1.5 flight controller drone also?
Because my drone is tilting on one side
Yes
You have to calibrate ESC in 2 methods for stable flight
1. Do the steps shown in video for all 4 ESCs
2. Calibration of ESCs using KK board:
-Remove supply
-Switch on TX and keep throttle to max
-Press and hold 1st and 4th button of KK board and connect battery
-you should get " throttle pass through" on screen of KK board
- wait for few seconds and decrease the throttle
-wait for few seconds
- remove battery
Note: don't remove buttons of KK until all steps are done in method 2
Did it solfve?
Can you also do this through betaflight?
Steps remain same.
Good describition for me!
Thank you 👍
Sir in my transmeter ch is not working when i connect my servo also its not working how to make a program for ch3
Have you binded your receiver with transmitter?
how much voltage battery have you used?
11.1 volt, 3S
Vai bike wali vedio kaab ayegi gear and brake
We will make it soon
Clutch part need some work
@@techathome Thanks for replying vaai
i have a problem my motor doesn’t start and do any beep when connected i have a flysky i6x can someone help me
Steps will remain the same on any model of Tx and Rx.
Try to change motor and ESC once.
Do it with fs ct 6b
Calibration steps remain same
@@techathome thankyou bro
Hello brother i tried your step and it producing same beep before and after but my motor running roughly like vibrating , please connect with me
Repeat the calibration as shown again.
If issue is exists, then try with different ESC.
Sir please help me my drone wings are rotate but fly
Check the motor layout and the propeller direction.
ruclips.net/video/UW1-gSySgxg/видео.html
The drone vibrates and tilts
Me also
Vibrates hai to propeller balance karo ❤
I want to rotate the motor in reverse also, so how do i calibrate it?
Keep centre yellow wire as it is and just interchange red and black wires at the motor
facing problem in high gps hdop
We have design flight controller using Arduino and mpu 6050 our problem is our motors are not rotating only beep sound is coming
Have you calibrated ESCs after buying.
@techathome yes
How can I contact you
Mail
If you have Transmitter and receiver, connect ESC directly to receiver and try to check if motor is running.
@@techathome ok
Salam sejahtera untukmu tuan....saya mempunyai esc simonk 30a seperti yg anda punya.....ada permasalahan dengan esc saya .kenapa esc saya berbunyi beep putus2 tidak henti2.mohon solusinya
What is the problem
@@techathome terima kasih atas perhatiannya
Permasalahannya karena saya pemula dan belum faham dengan rc plane. Kebetulan saya merakit diy rc plane arduino.
Jasi permasalahan diatas sudah selesa.trima kasih banyak.i
My drone motor is not working i do esc calibration many times
Need to check with other ESC once to find out where motor is working or not
Sir my mortors are only vibrating not rotating I had did the setup more than 5times 🥺
If ESC is not working, then also this might happen,
You have to check the same motor with different ESC
Also have you done the connection as shown in the video?
Aoa bro help me
Beep sound not coming
Still try to follow the same step and see if motor works.
probly if the motor doesn’t beep and doesenta start the esc is broken
Yes
But the reciver is working with The esc is it means the esc is broken ??@faracollo12
Receiver will work because it is getting 5v supply from the ESC.
But to run the motor, there will be MOSFETs inside ESC which might be not working.
I am hearing 3 beeps
No issues if you get more beeps
I have a 6 motor drone, when I want to fly it, 3 motors turn off and don't spin, what is the problem, and what is the solution, I use esc simonk 30A
If you are using APM you can follow this tutorial : ruclips.net/video/jHaYAA_Km7Y/видео.html
Check motor connection, ESC calibration
My Drone take off after 50 % throttle
Can we re calibrate also are it’s only once we can set ?
You can calibrate any number of times