What Resistor Should You Use For Steering Wheel?
HTML-код
- Опубликовано: 21 ноя 2020
- Wondering how to turn that airbag-light off? How many ohms etc? Get your answers in the video.
Keep in mind if you are doing this while installing an childrens seat, please check that if your car have side airbag curtains that you are absolutely sure that nothing that isn't supposed to happen - can happen. Consult an technician if necessary. 
Авто/Мото
totally legit. worked On my 2004 ranger, got tired of getting "you are going to be blinded by our product" letters and removed the air from the bag region. 2 ohm .25 watt resistor shut the light off for me. liked and subbed.
Sick ride bro !! 😎👍
Thanks man wicked help. Lovely car btw
Thanks bro nice video
Thanks :)
your the man :) 1 want to remove my passenger seat from my nissan leaf can you show me what the plugs look like and what resister i need to use ? 2.2 or 3.3 ohm? would 1/4w be big enough
Hi bro nice video....1 question....from small car like... Mitsubishi mirage coupe...the resistance is the2 o 3oms thank s
Hey great video. If i wanted to make my own what can I use as prongs that will not affect the resistance? I tried using a 1.5mm solid copper wire 1.5 inches long on either side of the resistor, but it didn't work, I got a fault code from a functioning airbag with it plugged in to test if it worked. Would the fact I used a 1.5mm solid copper wire have made a problem and changed the resistance level from that the resistor that was 2.2 ohms 1/2 watt so then I got a fault reading when I know for sure was fine before I tested it. Thank you!
How would you do the right rear door impact sensor please on a 2018 colorado
My 2004 Honda Civic SiR has the airbag light on all the time. The connector that I need to use to turn of the light is impossible to get to up under the dash. Could I use a 2ohm resistor to short each SRS component one at a time to locate the problem? Will the airbag light clear automatically if I locate the right connector? Thanks, great video
so does it have to be 2, 2.2 or few 10ths(??) lower or higher than 3?
what is the resistance of the airbag to bypass the fault code?
Please what nimber résistants d'or stepway
Hello! Thank you for this information! I have taken my front seat out but people will still be sitting in the back seat when I am driving so I was hoping that if I connect the resistor to the connector coming from the car that the airbag would still be released in the case of a crash, to protect the person in the back seat from flying through the front window. Would that be the case or is it just a trick to turn the light off? Would the airbag still deploy with the resistor plugged in?
The front airbag will still function yes. I take that you want to put a resistor as a replacement for the non existing seat? The system as a whole will function as normal with a resistor. 😊
Hi there nice video. For Audi A1 seat belt what are the resistance valuers 2 or 3 ohrms
Great video!
Just one thought.
If u put a to small resistor in, the airbag light will se this as a faulty airbag and bring the light on.
But What happen if u put a to big in?
Yes that's correct. Depending on car it'll pop up an other fault code regarding this. It'll say something like "airbag circuit one implausible signal" or something like that 😊
Tjena, jag ska ha 2 ohm för min airbag, men jag frågade de på mr tuning och de sa en resistor per kontakt på airbag kudden. Kan du försöka förklara hur jag vet hur många jag behöver?
Tack
Hello.! Brother. Your ideas are awesome. I have a same problem related to my front passenger seat. I replaced my front passenger seat to the handicap seat. Now the indicator is blinking red light. What should I do now in this case.? I need solution from you. Could you please guide me.? I want the whole air bag system to be working well without blinking red light in the absence of front passenger seat. Is it possible brother.?
In this case resistors is the way to go. The thing is there's various preferences on cars regarding wich resistor to use. If you're unsure of wich works on your car. Grab yourself an scan tool and start with the resistor with the lowest value. If it doesn't fly - start over with one with a higher ohm-value.
I hope this will work out for you!
woher bekomme ich so einen stecker? ich brauche den für einen ford focus mk1
I have a Nissan also, with two plugs that go to my driver airbag. The yellow one and the orange one, do I put a resistor on each plug?
Yes, one resistor for each connector. :)
What if the passenger airbag is dual stage, using 2.2 ohm resistors makes the open circuit error codes disappear BUT the open vent squib error is still ocurring, what is wrong?
Let me know what car you are working on an what the fault code is. Hopefully I can help you. :)
2021 Tacoma, when I look on TIC I see strange ohm amounts listed such as below 1ohm - is this right?@@EFreddy
Hello, I got a problem with my ford focus 2010 seatbelt buckle. And I know ford has some steps to disable the seatbelt chime but I did that a few years ago and it worked until now, so I read some forums that said that the problem was the seatbelt buckle microswitch, therefore the complete seatbelt buckle assembly should be replaced.
Tbh im college student in Mexico so I dont have a lot of money to spend and I was wondering if I can do the same method to bypass my seatbelt buckle microswitch with a resistor as I saw the same method used in other makes and models.
So to simplify what I just wrote the question is, ¿Can I put a resistor? If I can ¿what would me the resistance in ohms?
I hope you answer because I drive this daily and the fucking chime is gonna make my head explode smh.
Can you post the link where yo buy them
This is the same as i used :) www.wish.com/search/airbag%20resistor/product/5a98c0e3d91790767e8c1c68?source=search&position=2&share=web
Might consider the air bag uses TWO ignition coils, one to each connector. If the connection is open, (not conducting) but the air bag is showing 2-4 ohms on each connector, a crash signal will only fire one of the two charges inside the air bag. If the connection inside the air bag is not reading 2-4 ohms then the air bag itself is failed, shorted or open. This is what the alarm is trying to tell the driver, a device is NOT arming properly. Bypassing it with a resistor will trick the control module to put the light back off giving a false sense of security. The problem is an under-inflated air bag may be more dangerous than NO air bag.
The engineer that developed the air bag died of a broken neck, (early 60's maybe) while testing a way-to-violent early design. Just be warned, if you sell the vehicle and the buyer is injured in a crash, whoever bypassed the circuit with a resister would likely be liable if discovered. Be wise.
Bought a 100pack and just wandered thru my neighborhood disabling airbag lights. Scam was easy. I offered to simply clean under all their front seats for free to test my new koken 1/4 drive flex neck. 💪 ps McLaren did not accept the 2.0 or 3 3, driver seat needed a 2.2 and the passenger required a 2.7 ohm resistor (2012 12C).. S10 (1999 ZR2) took all 2.2ohm including the DRL sensor in passenger dash soeaker...😅😊
my airbag deployed, I actually bought the resistor and manages to remove the fault code whenever I run diagnostic but the airbag light still on
Most likely theres something called "crash data" that is stored in your airbag ecu that need to be cleared.
Some brands can "restore crash data" via obd. Mercedes e.g. can do this. Others are more tricky and may need an airbag ecu swap and coding.
In witch yellow socket should I conect the rsistor for deployed side curtain airbag ? And what for the yellow socket under front seats ? And how to remove crash data from airbag module ?
If there are more than one airbag connector, it needs one resistor for each connector you encounter.
Regarding clearing crash data the answer may vary. If you are looking for clearing this yourself you should check out if the product "Carprog" has your car model in their vehicle list. Maybe you can find help there with that :)
@@EFreddy Thanks .
What watt would the 2 Ohm resistor require?
The ones I used in the video is 0.25w. :)
So if I put one of these in I won't trip a light?
That is correct. Keep in mind that IF there's more than one airbag-connector coming to your airbag -you need one resistor for each one.
...ALMOST fully correct. The front passenger seat air bag connector for a Citroen Belingo Desire 2005 is ' 3 ohm ' and not 2. Thats all...
dekui
No explanation enough, after putting a resistor inside of the steering, if you involve an accident , will replacement air bags help preventing injuries again ???
I'm not sure if I understand your question correctly. The system will work as normal without the removed component, when a resistor is installed.
what watts resistor?.
0.25 watts
Don't work
pongo la resistencia y la luz sigue encendia, aun resteando bsi con truco llave contacto, con app torque ni kitando bateria