Tip for everyone wanting to solve any modern electronics problem. 1st I check for obvious damaged parts, like resistors heat damaged (cooked) and electrolytic (polarized) can capacitors that are bad or getting bad - look at the top of all biggest ones to see if it is swelling and top is bulged up. Any bulging means it needs replaced. 2nd thing i always check is if there is any bad (cold) solder connections on the PCB's. Use some head worn magnifiers and inspect all ribon wire connectors, and all wire thru hole connectors that have a component that has a lot of mass to it. Large parts will cool solder down too fast when the device was manufactured and cause it to be a "Cold" joint to often. It might pass testing, but vibrations and heating and cooling cycles can make these weak connections eventually fail. Look for hair line cracks around the parts leg poking thru the hole. If any connection doesn't look like the good ones, it is suspect and should be resoldered. 90% of all repairs i do is finding and resoldering bad connections on modern consumer electronics. The lead (pb) free solder used now in manufacturing suffers greatly from doing this. I use 60/40 solder to make the repairs by heating the connections and adding solder to make sure it is a "wet" connection. Be sure to not make any solder bridges to a nearby connection or known as a "Short circuit". A great additional soldering aid tool is a solder sucker for removing excess solder or to remove a part and clear the hole of solder so replacement part can be mounted as original part was. Every solder connection must meet 2 conditions in order to be a proper good joint: 1 it must provide the best possible electrical connection between components that can handle The current flow. 2 it must provide structural support for the component to prevent the solder from failing due to mechanical stress. If you make all connections meet these 2 requirements, you have performed the work correctly. After doing this inspection and working on suspected connections, then test the device to see if problem is solved. If problem persist, then do like this guy did and check for proper voltages from the power regulators. Some devices have multiple voltages they use, some only have one or two. NOTE: Always disconnect power from device before attempting to do any soldering. Never solder live circuits! Only use soldering irons, preferably a DC isolated one for sensitive electronics. NEVER use a Soldering Gun on low voltage circuit boards! Guns are a inductive method to heat the tip. There can be a high current flowing thru the soldering tip that can destroy sensitive semiconductors on low voltage circuit boards. Hope this helps everyone and good luck. Thanks for this video sir, it is a very good informative example of troubleshooting a device and repair solution. I have the same stereo to fix for a friend with same error code.
Muito bom a sua explicação, vc esta de parabéns, é desse grande técnico que precisamos pois passa o ensino. Aqui no Brasil tem uns que guarda o que aprendeu. Abs e muito obrigado.
If I remove cassette player and DVD player then only audio amplifier will work? I mean can I play the set without cassette and DVD player? I have (sa ak 85)
@@glenntips thank you so much. But after removing my cassette and DVD player then my set get power but when I press AUX or another buttons then my set get F61. But it was working once after removing cassette and DVD. But after that it is standing on f61 till now. So I was confuse.
@@binodon-hub2685 maybe there is another problem, also sometimes when the blower wont connect there is f61, also try to look at the amplifier section or the relay maybe there is a loss connections
Thanks for the information,, please my own Panasonic it will on standby but, when I click it,it will dim 🔅 and the replay will click but not display anything in timer and it will go back to full timer
Hello sir my panasonic sa-dk20 show f61 error before f61 the only subwoofer and center speakers work and rsn311w64 is very heat up and fan isn't working and one day when i power the music system its show f61 error i think the rsn311w64 ic is damaged? plzz tell me i am correct
Sir when i power the system it show f61 error but the power amplifier ic isn't heat up it cool down before f61 error the only 2 channel work and rsn311w64 is very heat up
Sometimes if the cooling fan doesn't work, it makes an error f61,check the input signal in front speaker and make sure if there is no loss contacts, also check the fan if its broken. If not, trace it if were is connected
@@glenntips sir before showing error f61 the cooling fan isn't working i checked the cooling fan separately but it work and then i put it again it doesn't work i 100% sure the rsn311w64 is damage i order rsn311w64
I have a Panasonic sa vk760d As i turn on the system and play something,after sometime it freezes ,nothing changes and when i turn of from socket it makes a thud noise
Yah mujhe speaker banvana hai Panasonic uski picture to maine aapko send kar sakta hun aur banvana hai aap banaa dete to aapki meherbani Hogi is chij mere pass padi Hui hai
I'll appreciate every one who can help me ... whatever the way should be...I want to fix it...video conference might help...if there is someone who can help me..plz answer to this comment
![BLACK BAG - Official Trailer [HD] - Only in Theaters March 14](http://i.ytimg.com/vi/Du0Xp8WX_7I/mqdefault.jpg)
![[002] [T.E.A.H] - Panasonic CRS1D DVD CHANGER DISASSEMBLY (For SA-VK950) - S01E04](/img/1.gif)
Tip for everyone wanting to solve any modern electronics problem.
1st I check for obvious damaged parts, like resistors heat damaged (cooked) and electrolytic (polarized) can capacitors that are bad or getting bad - look at the top of all biggest ones to see if it is swelling and top is bulged up. Any bulging means it needs replaced.
2nd thing i always check is if there is any bad (cold) solder connections on the PCB's. Use some head worn magnifiers and inspect all ribon wire connectors, and all wire thru hole connectors that have a component that has a lot of mass to it. Large parts will cool solder down too fast when the device was manufactured and cause it to be a "Cold" joint to often. It might pass testing, but vibrations and heating and cooling cycles can make these weak connections eventually fail.
Look for hair line cracks around the parts leg poking thru the hole. If any connection doesn't look like the good ones, it is suspect and should be resoldered.
90% of all repairs i do is finding and resoldering bad connections on modern consumer electronics. The lead (pb) free solder used now in manufacturing suffers greatly from doing this.
I use 60/40 solder to make the repairs by heating the connections and adding solder to make sure it is a "wet" connection.
Be sure to not make any solder bridges to a nearby connection or known as a "Short circuit". A great additional soldering aid tool is a solder sucker for removing excess solder or to remove a part and clear the hole of solder so replacement part can be mounted as original part was.
Every solder connection must meet 2 conditions in order to be a proper good joint:
1 it must provide the best possible electrical connection between components that can handle The current flow.
2 it must provide structural support for the component to prevent the solder from failing due to mechanical stress.
If you make all connections meet these 2 requirements, you have performed the work correctly.
After doing this inspection and working on suspected connections, then test the device to see if problem is solved.
If problem persist, then do like this guy did and check for proper voltages from the power regulators. Some devices have multiple voltages they use, some only have one or two.
NOTE: Always disconnect power from device before attempting to do any soldering. Never solder live circuits!
Only use soldering irons, preferably a DC isolated one for sensitive electronics.
NEVER use a Soldering Gun on low voltage circuit boards! Guns are a inductive method to heat the tip. There can be a high current flowing thru the soldering tip that can destroy sensitive semiconductors on low voltage circuit boards.
Hope this helps everyone and good luck.
Thanks for this video sir, it is a very good informative example of troubleshooting a device and repair solution. I have the same stereo to fix for a friend with same error code.
Eres un crack 11:04
Quisiera aprender más sobre tus videos
Saludos desde MÉXICO
Nice conversion. Absolutely applicable to all devices.
Very detailed and informative
Muito bom a sua explicação, vc esta de parabéns, é desse grande técnico que precisamos pois passa o ensino. Aqui no Brasil tem uns que guarda o que aprendeu. Abs e muito obrigado.
You are very welcome
When you replaced the regulator with the other one, do you have to disconnect the original one?
No didn't remove the connection I just parallel it, it's ok because there is no shorted at the original regulator, it's just droping
Sorry, I am unclear, did the new regulator go on a heatsink, does it not get hot?
Not too hot, just moderate
If I remove cassette player and DVD player then only audio amplifier will work? I mean can I play the set without cassette and DVD player?
I have (sa ak 85)
Depending on the model, there is also a model where the funtion will not work when the dvd is disconnected, but try it sir maybe yours will work
@@glenntips thank you so much. But after removing my cassette and DVD player then my set get power but when I press AUX or another buttons then my set get F61. But it was working once after removing cassette and DVD. But after that it is standing on f61 till now. So I was confuse.
@@binodon-hub2685 maybe there is another problem, also sometimes when the blower wont connect there is f61, also try to look at the amplifier section or the relay maybe there is a loss connections
@@glenntips Yes, it can be happen.
Very good job
Good job sir
Nice job....
Thanks for the information,, please my own Panasonic it will on standby but, when I click it,it will dim 🔅 and the replay will click but not display anything in timer and it will go back to full timer
Maybe there is a shorted parts in it,check all voltages if all are present when you turn it on
Can you please suggest some music player for this type of speakers. Like(red,black;blue, white) pair cable from speaker
You can use any home theatre player as long as their watts are the same
Apka shop kaha per hai
Kyuki mere panasonic 5 cd changer stereo music system me bhi f61 error show ho rha hai
Philippines
Which model?
I have a panasonicBI-System SA-AKC73 it won’t play cd or do anything can you help me
My cd surround is not working. ND having volume issues.also led light
Try checking the connection of the speakers and the volume control.
Sir ano kaya 56 md error niya. May power pero wala audio na lumalabas. Panasonic sa pm70 unit. Thanks
Assalam walekum bhai jaan kya hal hai tiktok bhajan mere pass Panasonic ka sound pada hua hai speaker Panasonic
AK48 or AK78...
😊😊😊
Boss gd am san lugar ninyo ipaayos ko sana stereo ko may power pero d gumagana cd st fm
Laoag city sir
Hello sir my panasonic sa-dk20 show f61 error before f61 the only subwoofer and center speakers work and rsn311w64 is very heat up and fan isn't working and one day when i power the music system its show f61 error i think the rsn311w64 ic is damaged? plzz tell me i am correct
Maybe you're right, but check first if there's a shorted at the speaker out so the amplifier get too hot
@@glenntips i cgeck it but not shorted and one other problem the amplifier cooling fan isn't working
Sir when i power the system it show f61 error but the power amplifier ic isn't heat up it cool down before f61 error the only 2 channel work and rsn311w64 is very heat up
Sometimes if the cooling fan doesn't work, it makes an error f61,check the input signal in front speaker and make sure if there is no loss contacts, also check the fan if its broken. If not, trace it if were is connected
@@glenntips sir before showing error f61 the cooling fan isn't working i checked the cooling fan separately but it work and then i put it again it doesn't work i 100% sure the rsn311w64 is damage i order rsn311w64
Yes brain at work
Halo teman saya dari indonesia. Apakah ini bisa diterapkan pada seri vk62d. Terimakasih
Maybe, just try to measure voltages, if theres a missing voltages
Panasonic speaker hai mere pass pade Hain yah pura model hai sit
If E61 error?
How can I contact you
Location sir?
@@glenntips Durban
What's the resistor ohms and watt pls
220 ohms, 3watts
Sir ano kaya fault neto same sa unit mo wlang signal na pumasok sa tuner at aux. Di ko.matest din cd at tape parang stuck na..
Subukan mo muna magtest ng voltahe sir baka may missing lng o kaya may nagloss connection , check mo rin ang main amplifier kung may signal
Boss mag pa repair din sana ako sa stereo ko ganyan din
Free good jop
Good evening
in power supply unit no 6v d.c. supply coming to the relay,
how to repair
You mean in primary section? Check the standby transformer and also the retifiers on the standby transformer,
I have a Panasonic sa vk760d
As i turn on the system and play something,after sometime it freezes ,nothing changes and when i turn of from socket it makes a thud noise
Maybe it has a loss connection or cold solder
@@glenntips like inside the system cables?
Como sintonizar canais de rádio fm
What's wrong with your radio?
My problem is in cd load, they no change or load the cd inside.
el mio dice ECHO y no se como desligar eso
Ya sama ky punya saya ada yg bisa bnerin ga
I have SA-HT80 penasonic its f61 errior how to fix
Check all voltages sir,
Maybe there is missing
I need your help brother if possible I also have a Panasonic amplifier but the problem is audioo
@@glenntipsI need your help brother if possible I also have a Panasonic amplifier but the problem is audio
@@gur5262what kind of amplifier sir? Is the same as the one i repaired?
My also same problem if you solve it send your phone no
Yah mujhe speaker banvana hai Panasonic uski picture to maine aapko send kar sakta hun aur banvana hai aap banaa dete to aapki meherbani Hogi is chij mere pass padi Hui hai
Send your Fb, mesenger
Panasonic vk550 f61 problem PC board no voltage
I'll appreciate every one who can help me ... whatever the way should be...I want to fix it...video conference might help...if there is someone who can help me..plz answer to this comment
F61 notification coming plz help me
Check all voltages maybe there is missing and also the relays if the solder is not connected properly
Panasonic c.d. system SA-AK87 power supply Unit no 6volt D.C coming to the relay
please don't show every day same VIDEO Thanks
What do mean?
like
Panasonik sa vk 660 . Ref no. Q5101 parts value REF no Q 5111 parts value sendme
.puya sayah mati power nya gk yala gimna
Sorry i couldn't get your question?
Pano ba kita makontak 😊
Location mo sir?
Rolo de loco eres dando tituriales eres mudo o que carajo
El audio es malísimo no se entiende nada
Please read the letters below😊
Panasonik sa vk 660 bord no .Q 5111 parts value . Q 5101 parts value send me
Sorry I don't have that model right now
@@glenntips ok
@@glenntips ok
Achcha bhajan yah banvana hai mujhe yahi Samsung chij pada hua mere pass banvana banaa sakte ho aapka number mujhe Bata do Rasta
Aapko Maine follow bhi Kiya hua hai aur aapka number send kar dena mujhe banvana hai paina song speaker