PRODUCTS USED IN THE VIDEO DOWN BELOW Molds- globmarble.com/paving-concrete-stone-mold-ss-5303.html Heavy Duty Bucket- globmarble.com/index.php?route=product/search&search=bucket Mixer- globmarble.com/decorative-concretes/concrete-tools-and-supplies/concrete-mixers3/ Vibration Table- globmarble.com/index.php?route=product/search&search=vibration%20table Vibration Motor For DIY Vibration Table- globmarble.com/index.php?route=product/search&search=vibration%20motor
Thinner consistency of concrete, preferably achieved with a superplasticizer. Avoid adding large aggregate like gravel. Sand and cement will do just fine for very small molds
You will probably need more as the concrete is fluffier before you add water. Our website has detailed mix and casting instructions for each mold we sell so you don't have to worry about that :)
We sell the molds worldwide :) You can check the description of the video for the exact materials I used in this video, or you can browse all of our products here- globmarble.com/
Hey Vlad, My name is also Vlad 😂, quick question. We live pretty close to each other, have you tried looking for a supplier to get some lightweight aggregate in bulk for the concrete mix, like pumice, lava rock or perlite ? Was wondering what your though on these aggregates are, have you tried any?
Yes, I have played around with these aggregates. My conclusion is that these aggregates absolutely make the concrete lighter but at great detriment to the strength and PSI. The best alternative in my opinion is using a prebagged lightweight mix like XS LightWeight. The manufacturers are wizards who put additives most people wouldn't be able to pronounce to get the best combination of reduced weight and strength. - globmarble.com/xtreme-lightweight-concrete-mix-3.html
Thanks! We usually make our own concrete mix with only sand, cement, and plasticizer but I wanted to make a quick video with just premixed bags of concrete. Every mold on our website has detailed mix instructions with the amount of each material you will need per casting :)
Since you used the leftover dried product line to measure how much concrete to remove wouldn't it be true that you could fill your mold with water, pour into a bucket, mark the fill line and then use that much dry ingredients? Then weigh that to figure out how much water to use?
have you ever used fiber in your concrete ? The same concept method as using dyed concrete only in half of the mold to save money , using fiber is the same way , pour dyed or not dyed concrete first in the mold then the second batch would have the fiber in the concrete , then vibrate.
PRODUCTS USED IN THE VIDEO DOWN BELOW
Molds- globmarble.com/paving-concrete-stone-mold-ss-5303.html
Heavy Duty Bucket- globmarble.com/index.php?route=product/search&search=bucket
Mixer- globmarble.com/decorative-concretes/concrete-tools-and-supplies/concrete-mixers3/
Vibration Table- globmarble.com/index.php?route=product/search&search=vibration%20table
Vibration Motor For DIY Vibration Table- globmarble.com/index.php?route=product/search&search=vibration%20motor
No plasticisers used in the project?
Can you help me, please? I am using plastic ABS paver molds. As the mortar is drying, it is developing cracks within the mold.
Quick to the point and he does not leave you with a questions. Many videos go on and on about nothing.
Glad you enjoyed!!
Thanks dude! Old man here contemplating funky retaining wall block design.
Glad I could help!
Thank you very much for taking the time to show us in detail how to... Deeply appreciated
!
Glad you found it helpful!
This was one of the only videos I could find THAT WAS GOOD that used sakrete rather than quickrete thankyou for this
I'm glad it helped!!
The weight calculation was helpful. Thanks!
Glad it was helpful!
Helpful info. Thanks!
Glad it was helpful!
thanks for the tutorial!
Glad you liked it!!
What is the easiest way to pour into a small mold? Thank you. Linda
Thinner consistency of concrete, preferably achieved with a superplasticizer. Avoid adding large aggregate like gravel. Sand and cement will do just fine for very small molds
Nice finish on the paver.
Thanks!
Favor done.. thanks for sharing your knowledge
Glad you like it!!
Thanks that was great, still work well with my Glob Marble molds!
Thanks!!
Good advice
Glad it was helpful!
Thanks for the video!
Glad you liked it!
cool cool thanks
Glad you enjoyed it!
Nice video. Im wondering if you fill a mold to the top with dry cement is that roughly how much cement you need for that mold?
You will probably need more as the concrete is fluffier before you add water. Our website has detailed mix and casting instructions for each mold we sell so you don't have to worry about that :)
Quite educative
Glad you liked it!
love it ..how do i get this to southafrica
We ship worldwide, you can find links to all of the products I used in this video in the description of the video :)
Great video thanks
Glad you enjoyed it!
Loving my molds
You have any from GlobMarble?
I want to see a video on how to use these stepping stones
That video is coming soon!
Thks
Any time!
It looks a little large, so how is it a attached to the wall? Do you drill holes ?🤔
This is a Stepping stone border mold, it is installed on the floor. We are coming out with a new video showing how to cast and install them soon!
Very nice 👍
Thank you 👍
You can show the formula of all kinds of stones
We have the formulas for every mold we have on our website :)
Nice
Thanks!
I want to do this work but i don't get the molds in my country
We sell the molds worldwide :) You can check the description of the video for the exact materials I used in this video, or you can browse all of our products here- globmarble.com/
Dose the release agent do good even if you add the iron oxide directly on the mold ?
Yup!
Hey Vlad,
My name is also Vlad 😂, quick question. We live pretty close to each other, have you tried looking for a supplier to get some lightweight aggregate in bulk for the concrete mix, like pumice, lava rock or perlite ? Was wondering what your though on these aggregates are, have you tried any?
Yes, I have played around with these aggregates. My conclusion is that these aggregates absolutely make the concrete lighter but at great detriment to the strength and PSI. The best alternative in my opinion is using a prebagged lightweight mix like XS LightWeight. The manufacturers are wizards who put additives most people wouldn't be able to pronounce to get the best combination of reduced weight and strength. - globmarble.com/xtreme-lightweight-concrete-mix-3.html
Keep the good work
Thanks man!!
Great
Glad you enjoyed it!
I just commented for RUclips algorithm…. You’re doing nice work though👌👌 Subscribed
Thanks for the comment and sub!!!
Awesome video, is there a reason you don't use aggregate and plasticiser to make it stronger?
Thanks! We usually make our own concrete mix with only sand, cement, and plasticizer but I wanted to make a quick video with just premixed bags of concrete. Every mold on our website has detailed mix instructions with the amount of each material you will need per casting :)
Hey man is it possible to talk with you on anything? I’ve been looking into this job and would appreciate talking to a hustler like you about it
NICE
Thanks!
Thanks for the tips! ✌
No problem!
Since you used the leftover dried product line to measure how much concrete to remove wouldn't it be true that you could fill your mold with water, pour into a bucket, mark the fill line and then use that much dry ingredients? Then weigh that to figure out how much water to use?
That is definitely possible! It might be difficult to pour water out of a mold though!
good video
Thanks!
How many times can you use the molds
If stored, used, and cleaned properly they can last up to thousands of castings
What is a demold agent you spray in the moulds?
All tools and materials used are in the description of the video. The release I used was G1- globmarble.com/concrete-release-agent-g-1.html
Thanks !! Y just starting doing this and y locking for some molds , kann you help me with some adviced for starting?
How long does a mold this size need to set before removing the finished product?
Typically the next day, but you can speed up the process by using CSA concrete, like I did in this video- ruclips.net/video/klF9c4yz1VI/видео.html
beautiful!!
Awesome!
Thank you! Cheers!
How do you make the mold
You can buy it here- globmarble.com/concrete-stones/concrete-stone/
Nice
Thanks!!
have you ever used fiber in your concrete ? The same concept method as using dyed concrete only in half of the mold to save money , using fiber is the same way , pour dyed or not dyed concrete first in the mold then the second batch would have the fiber in the concrete , then vibrate.
Yes, that is most common when doing countertops, you would spray the face coat and then do the backer coat which is packed full of fibers
@@GlobMarbleDo you need to add fiber when making outdoor pavers?
Great job!
Thanks!!!
Interesting
Thanks!
Cool
Thanks!!
🔥🔥🔥💯 enjoyed this video.
Glad you enjoyed!
Wow
Check out some more videos to learn coloring techniques!
Commenting to comment ! Screw that algo !
Thanks dude, I appreciate it!
Word.
Comment left
Thanks!!
boom
Here's a comment.
Appreciate it!!
Q
Nice
Thanks!