For anyone having difficulty with the lid part of the video and getting an error that reads "Flow Simulation Error - Face is not laying on the boundary between solid and fluid region.", put the model in cross section form and press the inner face of the lid. He mentions it in the video but when he presses the model it looks as if he pressed the outer face (he didnt) which is what actually renders the error.
Thanks! Great Tutorial! I believe the reason the nozzle helped mix your fluids was because when it accelerated the flow, it increased the Reynolds number and brought the flow from laminar into the turbulent flow regime. Turbulent flow will offer much more mixing than laminar flow. Does Solid Works Flow calculate Reynolds numbers? Or is that more of a "bulk" fluid number that doesn't make sense to calculate for individual fluid elements.
Question: What if the inlet flow relies on pressure? For example i have a model which has a compressor that will supply air into nozzles. What if the initial condition of the model requires pressure but not flow rate? What should i do?
i customized my menu and added flow simulation but i did something ( reset to factory defaults i guess) that i cannot find the flow simulation option the next time even in the customize option. where and how can i find flow simulation option. please help me
this is because no install flow simulation option when installed the products of SolidWorks. Re install the solidworks agin and activate the flow simulation option through the install
@@bartleycai2759 Thanks soo much Bartley! I'll that is most likely an issue I need to pay more attention to. I'll continue to refine the design and test the results.
For anyone having difficulty with the lid part of the video and getting an error that reads "Flow Simulation Error - Face is not laying on the boundary between solid and fluid region.", put the model in cross section form and press the inner face of the lid. He mentions it in the video but when he presses the model it looks as if he pressed the outer face (he didnt) which is what actually renders the error.
User level - God!
Great tutorial! Thanks for sharing! My only request is a few configuration iterations on mesh development.
Thank you Matthew for your time and expertise.
Thanks! Great Tutorial! I believe the reason the nozzle helped mix your fluids was because when it accelerated the flow, it increased the Reynolds number and brought the flow from laminar into the turbulent flow regime. Turbulent flow will offer much more mixing than laminar flow. Does Solid Works Flow calculate Reynolds numbers? Or is that more of a "bulk" fluid number that doesn't make sense to calculate for individual fluid elements.
thank you soo much, am new in solidworks and I am looking forward to learning more from your knowledge.
Should do a study of an Innova disc golf disc. "Hello, Innova here doing a study on Innova."
Fantastic presentation. Well done!
very good explanation and presentation. Can you explain about super sonic flows on boundary layers, and how to set up the mesh properly.
This is very useful...thank you very much!
Very nice! I hope to be able to analyze similar structure for combination of gas.
very well explained! Thanks for sharing.
This was brilliant. Thank you so much!
thank you very much, that's so helpful
Question: What if the inlet flow relies on pressure? For example i have a model which has a compressor that will supply air into nozzles. What if the initial condition of the model requires pressure but not flow rate? What should i do?
It's very helpful. Thanks yoiu so much!!!
Its very helpfull thank you so much
Thank you this was very helpful
I think is because your model is not enclosed properly. Not sure though. Are you running the Flow Simulation in an assembly part?
Thank you for the great tutorial, Do you have any tutorial about heat transfer (radiation) through multi-layers wall
Great video, Thanks.
Please tell me, why after clicking run simulation, program reports that monitor cannot connect to solver. What can it be? Thanks in advance.
This is because the your computer has low space RAM> This is problem also happened with me
i customized my menu and added flow simulation but i did something ( reset to factory defaults i guess) that i cannot find the flow simulation option the next time even in the customize option. where and how can i find flow simulation option. please help me
this is because no install flow simulation option when installed the products of SolidWorks. Re install the solidworks agin and activate the flow simulation option through the install
Just a little comment. If you add 1 g/s of water and 0,1 g/s of etanol, the volume fraction you would try to achive is 0,1/1,1 = 0,091 and not 0,1.
For some reason I can't get the water to flow to all parts of my model. It only really flows in the main pipe but not the lateral pieces.
Check your gap sizes in your mesh settings so that the solver recognizes that there is indeed a "hole" or branch. Or check your trajectory sizes.
@@bartleycai2759 Thanks soo much Bartley! I'll that is most likely an issue I need to pay more attention to. I'll continue to refine the design and test the results.
thnx
I am interested in simulation, can you help me make a horizontal centrifugal casting simulation tutorial, using the SolidWorks application. thank you🙏
Awesome!!
same problem
no idea what to do
did you figure it out yet?
can you do a heat transfer tutorial on heatexchnger plz
it's great
is possible to use the simulation on an assembly?
Great
Nope I am trying to run it on my sld part file
很棒！！
Hi Just wandered if you are still around and are you able to help??
Mike
The best
thank you soo much, am new in solidworks and I am looking forward to learning more from your knowledge.