Basics of SPI communication | Different modes of SPI communication
HTML-код
- Опубликовано: 30 июл 2024
- #SPIcommunication #SPI #communicationprotocols
0:00 Index
00:38 Basics of Synchronous communication
00:50 SPI Communication basics
2:44 SPI connections
04:10 Chip select of SPI
04:59 Modes of SPI
05:31 Mode 1
05:56 Mode 2
06:30 Mode 3
06:56 Mode 4
More Videos:
Embedded Systems:
I2C Communication Part 3: • Advantages & Disadvant...
I2C Communication Part 2: • I2C Frame structure Un...
I2C Communication Part 1: • Basics of I2C communic...
UART Communication Part 2: • Understanding UART Com...
UART Communication Part 1: • Basics of UART Communi...
Basics of Communication: • Communication protocol...
Power Electronics:
Power Factor Correction - • Power Factor Correctio...
Power Factor - • What is Power Factor |...
Powe Supplies:
Full Bridge Converter - • How does a Full Bridge...
Half Bridge Converter - • How does a Half Bridge...
Zeta Converter - • How does a Zeta conver...
Cuk Converter - • How does a Cuk convert...
Buck-boost converter - • How does a Buck Boost ...
Double Ended Forward converter - • Double Ended Forward C...
Active Clamp Forward Converter - • Active Clamp Forward C...
Forward Converter - • How does a Forward con...
SEPIC converter part 2 - • SEPIC converter design...
SEPIC converter part 1 - • SEPIC converter design...
Flyback converter part 2 - • Flyback converter desi...
Flyback converter part 1 - • Flyback converter desi...
Push-pull converter part 2 - • How to design a Push p...
Push-pull converter part 1 - • How to design a Push p...
Boost converter design - • How to design a Boost ...
Buck converter design - • How to design a Buck C...
SMPS basics - • Basics of Switch Mode ...
Electric Vehicles:
Battery management system 2 : • How does a BMS (Batter...
Battery management system 1 : • What is a Battery Mana...
Battery basics part 4 : • Electric Vehicle batte...
Battery basics part 3 : • What are the types of ...
Battery basics part 2 : • What is SOC, SOH, SOP,...
Battery basics part 1 : • Which Battery is used ...
EV motor controllers part 2: • Motor Controllers in E...
EV motor controllers part 1: • Motor Controllers in E...
Charging of EVs: • Working of Electric Ve...
EV basics: • How does an Electric V...
EV parameters: • What is inside the Ele...
EV Motors: • Motors used in electri...
---------------------------------------------------------------------------
Check us out!
Facebook - / foolishengineer-407598...
Instagram - / foolish_engineer
Subscribe now for more videos like this!
Attributes:
1. microcontroller - a href="www.freepik.com/free-photos-v..."Background vector created by freepik - www.freepik.com/a
2. IC - a href="www.freepik.com/free-photos-v..."Water vector created by macrovector - www.freepik.com/a 
Наука
Oh men you carried me so hard for my computer architecture exam 😂 Thanks! Keep going with your videos!
Thank you so much, Glad you liked it!!
Hello! great presentation. What is dual spi different from what you described?
Nice and Clear, thank you!
Thank you so much, Glad you liked it!!
You said that the chip select is an active low signal,which means its duty cycle is 0%. So how is it to the Vcc level?
Keep going, visual representation are very much helpful 🔥 big fan sir
Thank you so much, Glad you liked it!!
i want to insert a chip in the SS line. the microcontroller should pulse an address and the chip will multiplex the SS lines. i think this is a much better solution, given the specific application latency requirements do not prohibit it
I really appreciate your efforts and dedication bro 🔥, for such detailed animations and explanation.
Thank you so much 😀
Doubt in the modes and clk phase .
Communication between 1 SPI master device and 1 single slave SPI device generally always works well. But as soon as there is more than 1 slave, it's a big bazaar !!! Arduino libraries like SPI.h, + SD.h, etc, etc .... are not very well written and there are conflicts on the SPI bus (for example the SCK signal which remains high, CS signals which do not not go up, etc ... Read the forums and the excellent video of Sayanee Basu. Without a logic analyzer and a lot of development hours it is impossible to operate 1 SPI master device and only 2 SPI slaves. Not to mention the other connection mode, "daisy-chain". With I2C, I don't never had a similar problem.
We
why different modes are required? Any advantage is there with the indudial modes can you please answer for this?
I think it's for the engineering department. Most of us are just users even as semi-engineers. Each computer module is a computer, so they come to the door, call first or throw the package which is hidden for the usual code or life where we are, level 6 or something. In most cases we just follow the instructions to get it working. We buy "the best module" and that's all, so to speak. The top engineers are in another world, some future plans or something.
Amazing work brother. Please do AMBA soon❤.
Thanks!
Thank you so much for your super thanks!!
bro hats off to you.
Thank you so much for watching!! Please don't forget to subscribe to our channel
Very good
Thank you so much!
Superb explanation bro, which software your using to do animations
Thank you so much, Glad you liked it!!
I use After Effects
Nice video
Thank you so much, Glad you liked it!!
تشکر وهزاران لایک لطفا ویدیوها. را بزبان فارسی ترجمه نمایید ممنونم❤❤❤❤❤❤🙏🙏🙏
👍 If you have many slaves, you could chip select with a binary decoder whereas you only need 4 pins for selecting one of 16 slaves.
can you explain more about the modes
Okay, I'll work on it!
@@FoolishEngineer thanks ❤️
The Modes Listed In This Video Are Incorrect!!! I was just sent on a 6-hour wild goose chase trying to track down why my microcontroller wasn't transmitting in the correct mode based on the timings I measured on my logic analyzer, only to find out the modes listed in this video are incorrect, so it was working correctly the whole time! The video has the CLK Phase incorrect; therefore, Modes 1 and 2 and Modes 3 and 4 are switched!
Big fan❤️
Brooo!!!
Are bhai bhai....
Bete bete
Why this Protocols have master slave configuration
There must be only one who can initiate the data transfer,
Also there must be only one device which can control the clock for the communication, if both starts accessing the clock.
Clock line will get currupted by one-zero transitions.
Thank you so much for watching!!
Very good video but thoking language in speaking hindi please
Thank you for your feedback, I'll check!
Hate the way you have presented the visuals. All mixed
can i contact to you sir