Very helpful, thank you sv07 is our first 3d printer, there so many new things to consider, luckily there’s a logic here. I wish i knew what “tight enough” for the belt and screws meant, i will go with a gut feeling
Good video. Thanks for your help. Will subscribe. My wheels and springs came off of the screws on the bed and I had to figure those out. Still don’t know how to put filament in the extruder but I’ll check for another video.
Thanks for the video, I am having trouble understanding what labels you are giving things, perhaps baked in English sub titles (Auto captions have no idea what you are saying either) would be a good addition. Also I understand English is not your first language and appreciate you effort to speak it
There were many people asked during the launch of this printer if they are going to sell the klipper screen itself so they can hook on sv06s. But, nop.
Great stuff, I adjusted my bed level on the sv07 based on your tutorial. Thank you! Could you do a video where you look into input shaping? I did the input shaper auto-calibration on my machine and it messed it up realy bad and I have no idea on how to reset it to it's previous values. Do you have any advice?
@@SvgLau Thank you. I think the problem is with the accelerometer that they sent. After I resetted the printer to the factory settings and redone the bed levelling without the input shapper it started working well again.
Can you please help. Im having problems trying to get my sv07plus calibrated. I do the z tilt first, then the z offset and save. Then do the bed level. Got through it fine the first time. Tried printing the benchy. When it got about halfway done it started making a scraping sound and then knocked it off the bed. Tried several times and every time it did the same thing. So i tried calibratting again and this time it did the same thing. So tried it again, now when i do the z offset when i go to lower the extruder after lowering once at 5mm, and once at 1mm, and try going 1mm it says out of range. Also when trying to level the bed lile this i cant even loosen the bed srews enough to get it to even get anuwhere close to touching the paper on the left side, and on the right side the extruder touches the bed plate when it lowers. I am new to 3d printing and am lost at this point.
I think your issue may not be the bed leveling. As you mentioned your first few tiral benchy were stick fine on the build plate, the scraping sound could be belt skip steps or something. Did you adjust the belt tensioner and the eccentric nuts on wheels? This is critical part of basic calibration. If not, try to adjust those first and redo the entire bed leveling process. Also, if you are using the springs bed spacer set up, don't fully tighten it before you do the bed leveling. I fully tighten it and then, lossen like 2 full rotate just to leave a room for futher adjustment need on that direction. Also, if you can, try to slicer a slower speed benchy on slicer and try with that one first and see if it worked out.
Seit gestern steht der SV7 auch hier aufgebaut, aber drucken kann ich nicht. In der Y-Achse scheint ein Fehler zu sein und der Druck verschiebt sich. Man kann dann nur abbrechen. Ich habe deinen Teil mit der Kontrolle des Y-Anschlags nicht verstanden, vielleicht kannst du das noch einmal anders beschreiben worauf man hier achten muss?
Ich denke, Sie sollten zuerst versuchen, den Riemenspanner auf der Y-Achse einzustellen und dann die POM-Räder darauf einzustellen. Wie im Video gezeigt, sollte die Bewegung auf der Y-Achse linear sein, wenn Sie die Bauplatte bewegen.
@@SvgLau Thank you for the reply. I don't checked the excentric nuts. Now it goes and i have play a while to reproduce the stores filed on the USB stick correctly.
follow, thank you for all your effort to help the Sovol community!
thank you so much, i was looking at the user guide's wiring section and i was so confused but you've made it very clear!
I'm glad it helped!
Very helpful, thank you sv07 is our first 3d printer, there so many new things to consider, luckily there’s a logic here. I wish i knew what “tight enough” for the belt and screws meant, i will go with a gut feeling
Glad my video helps! happy printing.
Thanks for this video. Very helpful to use first timers!
Huge thanks for your videos and files! really appreciate all your help!
Good video. Thanks for your help. Will subscribe. My wheels and springs came off of the screws on the bed and I had to figure those out. Still don’t know how to put filament in the extruder but I’ll check for another video.
Yes a bit of lube on lead screws never hurts
Thanks for the video, I am having trouble understanding what labels you are giving things, perhaps baked in English sub titles (Auto captions have no idea what you are saying either) would be a good addition. Also I understand English is not your first language and appreciate you effort to speak it
The SV06 is so damn good I don't know why anyone would buy the SV07 instead.
There were many people asked during the launch of this printer if they are going to sell the klipper screen itself so they can hook on sv06s. But, nop.
What size is the part cooling fan behind the extruder?
What’s input shaping
Great stuff, I adjusted my bed level on the sv07 based on your tutorial. Thank you!
Could you do a video where you look into input shaping? I did the input shaper auto-calibration on my machine and it messed it up realy bad and I have no idea on how to reset it to it's previous values. Do you have any advice?
I will look into that, hopfully will have a video come out in few days.
@@SvgLau Thank you.
I think the problem is with the accelerometer that they sent. After I resetted the printer to the factory settings and redone the bed levelling without the input shapper it started working well again.
I followed your tutorial and it started to produce smoke
Can you please help. Im having problems trying to get my sv07plus calibrated. I do the z tilt first, then the z offset and save. Then do the bed level. Got through it fine the first time. Tried printing the benchy. When it got about halfway done it started making a scraping sound and then knocked it off the bed. Tried several times and every time it did the same thing. So i tried calibratting again and this time it did the same thing. So tried it again, now when i do the z offset when i go to lower the extruder after lowering once at 5mm, and once at 1mm, and try going 1mm it says out of range. Also when trying to level the bed lile this i cant even loosen the bed srews enough to get it to even get anuwhere close to touching the paper on the left side, and on the right side the extruder touches the bed plate when it lowers. I am new to 3d printing and am lost at this point.
I think your issue may not be the bed leveling. As you mentioned your first few tiral benchy were stick fine on the build plate, the scraping sound could be belt skip steps or something.
Did you adjust the belt tensioner and the eccentric nuts on wheels? This is critical part of basic calibration. If not, try to adjust those first and redo the entire bed leveling process. Also, if you are using the springs bed spacer set up, don't fully tighten it before you do the bed leveling. I fully tighten it and then, lossen like 2 full rotate just to leave a room for futher adjustment need on that direction. Also, if you can, try to slicer a slower speed benchy on slicer and try with that one first and see if it worked out.
Do ya still use this sv07
Seit gestern steht der SV7 auch hier aufgebaut, aber drucken kann ich nicht. In der Y-Achse scheint ein Fehler zu sein und der Druck verschiebt sich. Man kann dann nur abbrechen. Ich habe deinen Teil mit der Kontrolle des Y-Anschlags nicht verstanden, vielleicht kannst du das noch einmal anders beschreiben worauf man hier achten muss?
Ich denke, Sie sollten zuerst versuchen, den Riemenspanner auf der Y-Achse einzustellen und dann die POM-Räder darauf einzustellen. Wie im Video gezeigt, sollte die Bewegung auf der Y-Achse linear sein, wenn Sie die Bauplatte bewegen.
@@SvgLau Thank you for the reply. I don't checked the excentric nuts. Now it goes and i have play a while to reproduce the stores filed on the USB stick correctly.