@@BenBen-bv3kpесли молотком стукнуть по монтировке то ресурс ремня уменьшится до 10 минут вот смысл. 😂😂😂😂😂 if you hit the mount with a hammer, the belt life will decrease to 10 minutes, that's the point
Using a blunt tool will do little to no damage to the belt like others say it will. These belts are incredibly durable, after all they run many pulley like AC, alternator, powered steering, water pump and vacuum pump off of the crank pulley. These commenters are over exaggerating about how much the belts durability is affected just because the creator decided to not follow manufacturer’s procedure and do the job in an easier and more efficient way.
OBVIOUSLY something they put on like maybe one car and they don't tell you what car it actually was. so I'll just keep doing belts the old fashioned way. 😂
I mean everybody’s talking about using a different tool. I mean if he was using his head why wouldn’t he just stick it on the aluminum part and not touch the belt or the pulley all together?
What engine is this?? I’ve been a diesel engineer for 20 years and never seen that before…. Kinda wish I knew about that hack… or is it an American based engine?? Genuine question. Thanks
Мой ремень на vw пронхал 130000 км и поменял его вместе с грм. Ремни при. Этом не имели видимых трещин и т.п. здесь я не понял, что за фиксатор натяжителя. Кто то в курсе какой мотор?
@@thebaronwatson4610they think that using a blunt tool to disengage the tensioner by pushing on the belt will cause damage to it somehow. Maybe they think it might cause a little nick in the belt but they clearly don’t understand how durable these belts are
❤❤عزیزان همکار محترم قطعات صنعتی وخودرو بسیار ظریف وحساس هستند هرچقدر در این خصوص نهایت دقت ودقیق انجام شود بدلیل کارکرد در دورهای بالا کیفیت وزحمات کار ما بسیار بهتر وامید بخش خواهد شد ...یادما ن باشد همیشه خرابی ها وگرفتاری های فنی در مسخره ترین حالت ها وقصورهای کوچیک که فکرش رو هم نمی کنیم اتفاق می افتد ...تندرست وشاد باشین❤❤❤❤❤😂
my vehicle is made in America and not from 2024 where my tensioner actually has a way to lift it with a half inch ratchet so you dont have to do this bullshit
Yea typical German engineering, more parts more points of failure. What an absolute waste of engineering time and money, godforbid we put a 3/8” or 1/2” square in the mold for the tensioner arm let’s spend 1,000,000$ engineering a built in holder cuz we’re quirky.
People all worring about the belt, when im wondering 🤔 what the hell was stuck on the tensioner. ..
Me.too
Me 3
Me 4
Me Cinco
Cabrones, yo six 🤣🤣🤣
The life of the belt before operation is 50k km. The remaining life after the procedure is 5k km🤪
Pas tout à fait d'accord, la durée de vie des courroies est variable, entre 90000 et 120000 km suivant les nouveaux modèles.
@@BenBen-bv3kphe's just talking repair bad luck
@@BenBen-bv3kpесли молотком стукнуть по монтировке то ресурс ремня уменьшится до 10 минут вот смысл. 😂😂😂😂😂 if you hit the mount with a hammer, the belt life will decrease to 10 minutes, that's the point
Fr, I was going to say the same thing.
Should have shown how you set the spring pin on the tensioner of that mini cooper.
Ahh, thanks you said which poo is about, anyway I won't work never
Using a blunt tool will do little to no damage to the belt like others say it will. These belts are incredibly durable, after all they run many pulley like AC, alternator, powered steering, water pump and vacuum pump off of the crank pulley. These commenters are over exaggerating about how much the belts durability is affected just because the creator decided to not follow manufacturer’s procedure and do the job in an easier and more efficient way.
Процедура производителя очень сложна😂😂😂. Гаечный ключ на 30, вот и вся процедура без повреждения ремня. На этом двигателе простейший натяжитель.
С учётом того что на ремень летит песок и вода,думаю от монтажки он сильно обидится😂
Agreed, the barbaric "correct" installation of stretch belts is all the evidence needed.
No se ni que haces pero me encanta😂🎉
I have watched people use those belts to sling complete engines from a hoist. They're way way stronger than you think.
My motto is that I can fix it with the wrong tool faster than you can find your "right tool".
How many come backs you have clown
Why not push on the metal part of the pully?
Used a kinda sharp bar to push on the belt?
Müşterinin yolda kalması için yaptı hahahs😂😂😂😂😊😊😊
Pry bars aren't sharp.
That’s what the Bentley manual for Mini Coopers says to do. If your pry bars are sharp what did you do to them?
OBVIOUSLY something they put on like maybe one car and they don't tell you what car it actually was. so I'll just keep doing belts the old fashioned way. 😂
Just pull down on the belt at the bottom. The tensioner will move up 😮
1.6 Peugeot/Citroen
Mini r56
Еще есть такое на бмв
@@user-yc6bl2zz7q наверн с этим же мотором, 1.6
Монтажкой в ремень?!😳 силен мастер🤦♀️🤦♀️🤦♀️
I mean everybody’s talking about using a different tool. I mean if he was using his head why wouldn’t he just stick it on the aluminum part and not touch the belt or the pulley all together?
If he had pushed it on the aluminum part of the tensioner, the car would not come back for a new belt. it's called job security..😊
There’s a nut on the tensioner that could be turned on this engine, but the way demonstrated is exactly what it says to do in the manual.
Is the part he retracts back into place really to do with retaing tension pulley
Im going to find out tonirrow
Dude start from the beginning
That's the "Prince" engine developt by Peugeot and BMW with the silly water pump setup.
Lemme guess, that's some more of Ford's better idea's at work
Mini Cooper 😊
Freakin mini cooper! 😢Without that gadget or pulling the engine out, this is darn near impossible
А ключем сверху никак? 😂
Belt sure doesn't have much room next to the oil pan, no matter what kind of tools you use
Two minate job and a pay check later
Probably would of pushed on the bracket not the belt
Молодец ты испортил новый ремень😂😂😂😂👍
С чего это вдруг?
@@user-si9do7ex1t с того друг если тыкать монтажкой в ремень то он портится !!!! А если прислушался то слышен хороктерный звук надрыва ремня
@@user-mw2ib8ox5gуслышал только звук отщелкнувшего стопора на натяжителе и жужжание механизма включения помпы.
Тот кто не ремонтировал еп 6 так и говорит 😅
@@alexstrogov7042 я что на больного похож🤣🤣🤣🤣🤣🤣🤣
Why Yes, I have a couple belt killer 9000 models in my toolbox too..😜
I’m the mean time I bang the pry bar by a brutal hammer to make my right tools more completed.
What engine is this?? I’ve been a diesel engineer for 20 years and never seen that before…. Kinda wish I knew about that hack… or is it an American based engine?? Genuine question. Thanks
I have a flex head rachet that works unbeleivably well.
Got to love bmw
Looks like a good way to get comments
ЕР6 , на БМВ это двигатель тоже используется . Говно редкостное, хватает 150000 пробега .
Is this the 1.6 that BMW uses
And I bought the damn tool. That's bs
This is a good way to destroy the belt
No one's gonna know. How would they know?
Чтобы вы не придумывали для улучшения обслуживания, сама ваша техника с алюминиевым блоком цилиндров, и это на пару лет езды!
Мой ремень на vw пронхал 130000 км и поменял его вместе с грм. Ремни при. Этом не имели видимых трещин и т.п. здесь я не понял, что за фиксатор натяжителя. Кто то в курсе какой мотор?
It’s a mini cooper engine r56 there stupid designed tensioner for the water pump
All those reactions from vinegar pissing internet warriors ...
The 'damage' to the belt is nothing compared to wat it is designed to endure.
oh noo , it is a BMW !!!
What's that vehicle 😮😮
What just happened?..🤔
Sistemin sigortası gerçekten güzel düşünülmüş ve güzel çalışıyor
Mini or Peugeot
How to ruin a new belt…
How would touching the belt ruin it
@@thebaronwatson4610they think that using a blunt tool to disengage the tensioner by pushing on the belt will cause damage to it somehow. Maybe they think it might cause a little nick in the belt but they clearly don’t understand how durable these belts are
Now new belt is not really new anymore
What type of car? How did you install the tensioner?
❤❤عزیزان همکار محترم قطعات صنعتی وخودرو بسیار ظریف وحساس هستند هرچقدر در این خصوص نهایت دقت ودقیق انجام شود بدلیل کارکرد در دورهای بالا کیفیت وزحمات کار ما بسیار بهتر وامید بخش خواهد شد ...یادما ن باشد همیشه خرابی ها وگرفتاری های فنی در مسخره ترین حالت ها وقصورهای کوچیک که فکرش رو هم نمی کنیم اتفاق می افتد ...تندرست وشاد باشین❤❤❤❤❤😂
Prince engine?
Change the belt
Can someone please explain this?
I'm a technician of 20 yrs. Please don't do this. This here just knocked half the life off the belt.
Explain bro
Buena idea amigo
Schöne den neuen Riemen beschädigt bzw geschwächt 😅. Zeigt es noch Stolz im Video
He just trolling? Or he actually thinks he was doing something right here? 🤦
my vehicle is made in America and not from 2024 where my tensioner actually has a way to lift it with a half inch ratchet so you dont have to do this bullshit
На ЕР6 ремень меняется сверху, из-под капота.
А они с низу захотели 😂😂😂
what belt is this ?
And risk damaging the belt? Are you ok??
Блин, опять ремень менять
Creative technology ☝️🌲
pre historic
Блять там на механизме натяжения есть грани под ключ на 30 и все , под капотом 5 минут че блять придумываете
Вот-вот, а при должной сноровке гитару без подъемника поменять можно минут за 30
Citroen
Легендарный мотор от Бмв)
Pushing something sharp into the belt. ... genius idea 😂😂 not
La courroie va pas durer longtemps c quoi ce pseudo mécano je voudrais pas qu il touche à ma caisse celui la
Ep6?
Ep6?)
EP6 😂
What a tool
What was thingy thing on top of the pully tho?
Очень удобно!!!
Двигатель епи 6. Разработка BMW доделали французы. Если при правильном уходе мотор надёжный и экономичный.
Акстись акаянный мотор хуета, больше не скажи такого ни кому😂
Так это д.в. еп6.
Что это за "рулетку" вправили?🤔
Датчик износа ремня?
Ооо, Пежо)
Make of the vehicle please mention
Citroën or ds
Or mini
Or Peugeot 206 306 it looks like 1.6 vti
@@mrfxr1695 yes, i had one on a ds3 i think its a clever design. Change out the waterpump without taking off the belt
@@remonvisser9702 exactly, also safe, when belt breaks you lose AC not a water pump
But not correct procedure! You can throw that belt in the bin now!
Сверху лень за гайку потянуть?
Пежо такое пежо да )))
Обоснови чем он испортол ремен. Одним лёгким ножатием....
Mini cooper
Yea typical German engineering, more parts more points of failure. What an absolute waste of engineering time and money, godforbid we put a 3/8” or 1/2” square in the mold for the tensioner arm let’s spend 1,000,000$ engineering a built in holder cuz we’re quirky.
EP6?
Which car is this
Im guessing citroën or ds
Old mini Cooper s have this sistem
😂😂😂😂😂😂 nonno nooooo
Wtf is that?
Ep6😂
Говнище а не мотор 😐
Пиздец ремню)))
Самый конченый двигатель в мире ер6
Лень матушка
Ер6 навсегда))) сколько же он крови пьёт...
Que coche es
Mira que son malos esos motores... 😏
EP6 двигатель
EP-6
Citroen technologi
THP
Пежо ep6
🤔🤔🤔
Какая машина ?
Пыж 408
@@user-kk3cq2lc1d французы