This is the best video for these pumps. I am not a Deere guy but i just bought a 535 and still learning how to run these. Glad you took the time to make this video!
Well I spoke too soon. Neither the manual pull on rope or baling will trigger the twine arm. The belt is engaged when the door opens but the arm doesn't move. Any suggestions before we change out the pump?
@@hillbillylivestock4162 crack one of the lines off the pump to see if it has pressure. Sometimes if oil level was low you have to get air out of the system by bleeding it
What advi? what advice do you have fir when the twine arm stays in the right hand position till you yank the actuator plunger to the right to trip the arm into returning to the home position. Sometimes it runs fine and sometimes you have to manually trip the arm every bale
We've had the pump rebuilt twice and it still only has a trickle of pressure .you can cap it off with your thumb .belt is tight not slipping is it a low pressure pump?
I have a question - the bale size, or the manual pull causes the latch to trip and engage the belt that drives the twine arm pump. - I understand that part, but what causes that latch to reset and disengage the idler pulley so the pump shuts off?
Thanks. I don’t think mine bypasses after ejecting a bale and closing the hatch. The twine arm stops moving etc, but the latching mechanism never relatches to disengage the pulley, so the pump is constantly running.
@@obieacres4676we finally fixed it today! The latch connects to a spring, which connects to a rod that goes up. That rod has a screw and nut that can be adjusted up and down. We adjusted it down giving the latch more slack and it finally latched when the gate closes.
How did you prime the new pump after you installed it? We just installed a new pump on our 535 but now the twine arm won’t engage even when the belt does?
So crazy quesiton, I bought a 430 baler a few months ago, is it supposed to start wrapping on it automatically, or do you have to pull the string to start the twine arm
Thank you for showing this in action!! The 535 appears to be the same design, and this just saved me a lot of extra research.
@@CTC7599 glad I could help
This is the best video for these pumps. I am not a Deere guy but i just bought a 535 and still learning how to run these. Glad you took the time to make this video!
I am not a Deere guy either. This was my buddies baler I would never have one. Thanks for watching and please subscribing.
thank you very much for the video. i just bought one of the balers and could not figure out how to operate the arm. Perfect thank you
Thank you!
Showing the how and "what this does" helped us fix our baler.
Your very welcome
Well I spoke too soon.
Neither the manual pull on rope or baling will trigger the twine arm. The belt is engaged when the door opens but the arm doesn't move.
Any suggestions before we change out the pump?
@@hillbillylivestock4162 crack one of the lines off the pump to see if it has pressure. Sometimes if oil level was low you have to get air out of the system by bleeding it
@@obieacres4676
ok
what oil to pour into the string feed pump in john deere 430
ATF automatic transmission fluid
Buna ziua. De ce nu revine la loc parghia pecare o loveste bratul de sfoara pentru asi s
What advi?
what advice do you have fir when the twine arm stays in the right hand position till you yank the actuator plunger to the right to trip the arm into returning to the home position. Sometimes it runs fine and sometimes you have to manually trip the arm every bale
Check them springs on the bale size mechanism. Pump won’tstart if spring are to stiff or maybe try greasing it
We've had the pump rebuilt twice and it still only has a trickle of pressure .you can cap it off with your thumb .belt is tight not slipping is it a low pressure pump?
Low volume not sure what the pressure
It fairly high pressure make sure you bleed it and it going right direction
I have a question - the bale size, or the manual pull causes the latch to trip and engage the belt that drives the twine arm pump. - I understand that part, but what causes that latch to reset and disengage the idler pulley so the pump shuts off?
When the arm gets to the end the pump bypasses until you raise the bale hatch.
Thanks. I don’t think mine bypasses after ejecting a bale and closing the hatch. The twine arm stops moving etc, but the latching mechanism never relatches to disengage the pulley, so the pump is constantly running.
@@obieacres4676we finally fixed it today! The latch connects to a spring, which connects to a rod that goes up. That rod has a screw and nut that can be adjusted up and down. We adjusted it down giving the latch more slack and it finally latched when the gate closes.
@@smallacresfarm awesome them John Deere balers are complicated a lot of adjustments on them
why would my baler wind twine from the start of the bale?
@@fionamusgrove9007 one of your springs is likely bad
Any advice on why the twine arm won't engage? Recently bought an 88 model and when you pull the rope the arm won't start it's sequence.
It won’t start unless you have a bale in it or you raise the end gate
Or one of your springs is bad
How did you prime the new pump after you installed it? We just installed a new pump on our 535 but now the twine arm won’t engage even when the belt does?
Had to crack one line open and bleed it
@@obieacres4676 thank you.
Thank you. Really helpful video. Now I know 🤠
So crazy quesiton, I bought a 430 baler a few months ago, is it supposed to start wrapping on it automatically, or do you have to pull the string to start the twine arm
It is supposed to be automatic depending on where you have the bale size knob set.
The is just for when you want to start it sooner
PISTONUL CARE ELIBEREAZA SUPAPA DE SCHIMBARE A DIRECTIEI TREBUIE SA AIBA UN ARC? cU STIMA SI RESPECT GEORGE
Thank you your video really help me out
Your very welcome
Check out some of my other how to videos on farm equipment
Thank you for the explanation..it is much appreciated
Glad to help
Great job 👏🏽👏🏽👏🏽👏🏽👏🏽
Thank you for this video.
Your welcome I hope it helped
What GM pump did you use. It is hard to go by pics. Our pump is bad on our 530, JD want $900 for a new one. TIA
Thank you