one thing I see you can do to make your video extra educational is to add a 1 min brief into explaining the system you are test/troubleshooting. For instance here, what ia adblue valve? how does it work? What does it do? Etc. Thank you for making these videos.
That's a job done properly, note I believe the most common fault with these adblue injector valves is, they get blocked by the crystallized adblue at the outlet end, so even though the valve opens no adblue can get through.
Great video. Since the video show that the new injector value shows 13ohm . Is it possible to test resistance of the Ad blue injector value without removing it from the exhaust system?
I recently purchased a 2014 Sprinter and the check engine light came on and then the start count begin (10 starts remaining... ). I took it to a shop that diagnosed it as a failed DEF injector like you replaced. However after the repair, they cleared all codes but the DEF light on the dashboard came on. It wasn't on before and I had just filled my DEF tank. The shop is telling me that they need a MB Code reader to reset the DEF code otherwise it will go back into start count down. They will charge me $500 for this as they have to out source it to someone who has the MB code reader. I've read elsewhere that since the injectors been replaced, I should just drive it and the DEF light will go away on its own, unless there are other issues. What do you think?
@MrTrumpetbrian The DEF System might need to be reset by a factory scanner, 500$ is a lot for that though, you can take it to the MB Dealer and have them reset the light for a lot cheaper, unless there is another issue in the System!
@@KITS_Auto_and_Truck_Repair Thanks. I have an appointment at the dealer to scan and reset if necessary. In the meantime I'll drive the vehicle and maybe the DEF light will reset itself.
In some cases with my Vitos, after replacing the valve … the light didn’t go off, and I could not reset the fault code, however after driving it for about 25 miles it reset itself probably takes a while for the control unit to reset itself. The fault did not reappear.
Thanks for the video. I have tried everything to get the bolt loosened to remove the injector valve, but I can’t get it. What kind of socket did you use? I tried e-torx (e-4 through e-7) and normal 6 point sockets. It will not budge for me.
I have a 2022 Sprinter. Started up the van today and saw check engine light. Drove it for an 2 hours and got the message “Additive (Def) System Fault System Starts Emerg. Op: 10 See Operator’s Manual”
How are doing my man? I removed the valve, it was pretty clean, but it was crystalized all around. Also the nipple spins around. Does it have to be like this? Maybe it sipping because of it spins?
@@KITS_Auto_and_Truck_Repair Thanks for the answer. I removed the bracket, pulled out the nippel, there is an "o-ring", put a new one, became tight. Anyway, I know, the valve has to be changed. Found by a part number that you provided. Thanks again for the nice video 👍
I have a fault code on my sprinter saying EGR sensor A is faulty. Can you tell me where this sendd at or would be located ? 2014 Freightliner 3500 v6 diesel. I enjoy your videos
hi, u made a excellent video, I have that code and the engine lights comes on e comes off in My 2019 sprinter van, today I check the valve and I can see some white thing at conections looks like something leackind. what the best solutions, coz i dont know if I have to reset the sistem on dealership, please what do you think????
@@KITS_Auto_and_Truck_Repair I did, its good... but is leaking mabe it need a cleanup. so if i take it off and place ir agaim .. I gonna need to configurate it? so have to take on the dealer to reset?
Hi sr I’m buy the injector valve in eBay do you thing is it work for Mercedes sprinter and also my car have limp mode on I can not go more than 5mh please let me know
Love that you included the year and engine type. Thanks for all the great information and education. Amazing service you are providing.
@bobjones1620 My Pleasure!
one thing I see you can do to make your video extra educational is to add a 1 min brief into explaining the system you are test/troubleshooting. For instance here, what ia adblue valve? how does it work? What does it do? Etc.
Thank you for making these videos.
@abderrahimmark My Pleasure and Good suggestion! I briefly talked about the Adblue system in the video
Very good. Thanks. Please include showing the actual removal and replacement... That's always the bit we need to actually see.
@dingaling2007 My Pleasure!
That's a job done properly, note I believe the most common fault with these adblue injector valves is, they get blocked by the crystallized adblue at the outlet end, so even though the valve opens no adblue can get through.
@johnbower I agree with you, Thanks
Good Videos
@humbertoarellano8887 Thanks!
Helpful information ❤
@StarfishTaxisStAndrews Thank you!
Great video. Since the video show that the new injector value shows 13ohm . Is it possible to test resistance of the Ad blue injector value without removing it from the exhaust system?
@johnvu1449 Thanks, Yes
Keep it up,we are waiting ❤
@visalprabhashanaariyarathn4751 Thanks!
Good evening my friend
@buboybebing3716 Hello my Friend!
I recently purchased a 2014 Sprinter and the check engine light came on and then the start count begin (10 starts remaining... ). I took it to a shop that diagnosed it as a failed DEF injector like you replaced. However after the repair, they cleared all codes but the DEF light on the dashboard came on. It wasn't on before and I had just filled my DEF tank. The shop is telling me that they need a MB Code reader to reset the DEF code otherwise it will go back into start count down. They will charge me $500 for this as they have to out source it to someone who has the MB code reader. I've read elsewhere that since the injectors been replaced, I should just drive it and the DEF light will go away on its own, unless there are other issues. What do you think?
@MrTrumpetbrian The DEF System might need to be reset by a factory scanner, 500$ is a lot for that though, you can take it to the MB Dealer and have them reset the light for a lot cheaper, unless there is another issue in the System!
@@KITS_Auto_and_Truck_Repair Thanks. I have an appointment at the dealer to scan and reset if necessary. In the meantime I'll drive the vehicle and maybe the DEF light will reset itself.
@@MrTrumpetbrian Ok! Good luck
In some cases with my Vitos, after replacing the valve … the light didn’t go off, and I could not reset the fault code, however after driving it for about 25 miles it reset itself probably takes a while for the control unit to reset itself. The fault did not reappear.
@@StarfishTaxisStAndrews Thanks. I'm hoping that's what happens for me too (assuming no further issues with the DEF/DPF system)
Hello, thanks for the great videos so helpful. Could you please post a link for the part number for a 2019 Sprinter 2500? Metering Valve.
@zensauces My Pleasure! I don't have the part number, you can get it from your local MB Dealer!
Hi, thanks for the video! I have a question, what if the problem is with wiring, what should I do then?
@salva7449 you would need a wiring diagram and then fix the wiring!
Thanks for the video. I have tried everything to get the bolt loosened to remove the injector valve, but I can’t get it.
What kind of socket did you use? I tried e-torx (e-4 through e-7) and normal 6 point sockets. It will not budge for me.
@andymcrorie9128 you need a star socket for that!
I have a 2022 Sprinter. Started up the van today and saw check engine light. Drove it for an 2 hours and got the message “Additive (Def) System Fault System Starts Emerg. Op: 10 See Operator’s Manual”
@oatiko3065 you should have it scanned and see what code you have in memory!
How are doing my man? I removed the valve, it was pretty clean, but it was crystalized all around. Also the nipple spins around. Does it have to be like this? Maybe it sipping because of it spins?
@vladimirouvarov5416 it should not be sipping!!
@@KITS_Auto_and_Truck_Repair Thanks for the answer. I removed the bracket, pulled out the nippel, there is an "o-ring", put a new one, became tight. Anyway, I know, the valve has to be changed. Found by a part number that you provided. Thanks again for the nice video 👍
danke top
@sezginkaygusuz Good!
I have a fault code on my sprinter saying EGR sensor A is faulty. Can you tell me where this sendd at or would be located ? 2014 Freightliner 3500 v6 diesel. I enjoy your videos
@robbinbaker5497 it's part of the EGR Motor!
Is that repairable or should I replace?
hi, u made a excellent video, I have that code and the engine lights comes on e comes off in My 2019 sprinter van, today I check the valve and I can see some white thing at conections looks like something leackind. what the best solutions, coz i dont know if I have to reset the sistem on dealership, please what do you think????
@JoaoCarlos-li1jj do a resistance test of the valve!
@@KITS_Auto_and_Truck_Repair I did, its good... but is leaking mabe it need a cleanup. so if i take it off and place ir agaim .. I gonna need to configurate it?
so have to take on the dealer to reset?
Hi sr I’m buy the injector valve in eBay do you thing is it work for Mercedes sprinter and also my car have limp mode on I can not go more than 5mh please let me know
@vincenttran9134 No! don't buy the ebay ones, get the OEM one
Exact same reductant injector valve they sell 80$ unbranded and 160$ the one from Bosch...
@FrancoisOlignyLemieux Oh really?
Ok boy.tengo un codigo 2016 sprinter turbo diesel es.C428.
@mecanicajv1609 Thanks