Это видео недоступно.
Сожалеем об этом.
Voice Controlled Car using Arduino UNO # Hobby projects
HTML-код
- Опубликовано: 27 дек 2019
- Components
-Arduino UNO
-L293d Motor shield
-HC-05 Bluetooth module
-18650 Battery &charger
-Bo motor & wheel
click the link for circuit diagram :-drive.google.c...
To download Arduino IDE:-www.arduino.cc...
Arduino code :-drive.google.c...
AFMotor library download :-github.com/ada...
Softwereserial library :-github.com/Pau...
To download Bluetooth application:-play.google.co...
Thanks for watching
please Like, Share & Subscribe
![Chuckyy - Devil Hours [Official Music Video]](http://i.ytimg.com/vi/f3wZGj0VnZU/mqdefault.jpg)
ഇത് കൊള്ളാലോ 😃........കിടു 👌👌👌... keep up the good work...
I buyed all the things and connected the wires.BUT it still says when opening the sketch-could not open the skech.
t.me/HobbyProject
Message me
nice work and project
may your channel grow very fast
Hello sir,Can you plz tell me what is Tx,Rx that should I remove while uploading the code🙂
Tx -transmit data
Rx- receive data
when you upload a sketch to Arduino the rx-tx led blinks continuously as it is used in microcontroller for uploading sketch so if you have any module that is connected to Rx-Tx pins that data will flow into module also but as the data is for microcontroller and not for module the module itself might not interpret that data correctly and you might end up damaging the module.
@@hobbyproject I have lost my voice.Thank you very very much sir for replying and helping me.I have nothing to give you thanks.Love and best wishes from the core of my heart to you bro.
Sorry to disturb you sir,I have a question: Should I remove only the two wires that you have removed while uploading the code at the moment of 7:33?And should I connect the two wires that I have removed while coding?Plz answer me I have also made this car.After coding it will be ready to run.So plz answer me sir!😍😘
Yes .you need to connect the tx and rx after coding
Make sure that tx of bluetooth module connected to rx of arduino
and rx of bluetooth to tx of arduino
Good
I need to make another one.Should I connect the blutooth module's tx at the rx of uno.And rx at the tx of uno?And if I use Femeale to female jumper wires where you used breadboard,then will it work?Plz answer these questions ☺️
Yes. Breadboard is not required
@@hobbyproject Tnx,Sir!
Hello sir,I have a question.Plz answer me.What can I do for adding a obstacle avoidence sensor (Ultra Sonic sensor).Plz tell me.😄And if I say turn left/right ,Will it move to left/right side?
Yes it is possible. But you need to change the code
@@hobbyproject And can the robot move to left and right via voice command?🤗(Without changing the code?)And can you give the link of the code again.Plz plz😄
Yes
Hello brother I am big fan
Thank,s for your valuable support
Done all the connections.
Buyed 2 Bluetooth purchased 2 motor driver code is uploading also connection are all right but not working ☹️
Please reffer the circuit diagram .it works well
Pwoli👌👌👌
excellent വർക്ക് 💯👍🏻
Nice wrk mwthe
Great job👏
jishnu pwli
👌👌👌nice
Unable to download this arduino code ...showing like file format not supported... What should i do ? Plz. Reply
Use chrome for download.
Good work
😯Bro good work...
Can you make one for me
Nai i
Daave...
👌👌
Super
Bro pls make a bidirectional home automation without display and Google and Alexa home automation in one Arduino plss...
👌👌👌
Greate
Amazing✨
👍👍👌👌👌👌
Bro all is set but wheels are not rotating what is the problem plz solve it..
Good luck
im getting an error while compiling it says :
Compilation error: AFMotor.h: No such file or directory
include AFMotor.h library
i did everything same but the motors are not moving
Sir , can say how to make voice controlled drone
hello sir should we solder or just attach that pins to motor driver l293d to +5v andd gnd
Bro.. about which yellow wire u told to remove if we are giving power through arduino.
Could you pls look at my project? Codes are compiled and uploaded properly and I am able to connect my phone to the bluetooth module but it is not doing anything. Any help would be appreciated. Thank you.
7356919824 wts app me
❤️❤️❤️
I made the car but the Bluetooth module is not connected to my mobile there is bluetooth fault or some other
Why wouldn't it work with a 9v Battery? Earlier I was using 4 x 1.5 Volts batteries but they were not powering up the bluetooth module. Now I am using 9V, and my bluethooth module is working fine and I am being able to connect it to my phone through a different app.
How did you set up your app configuration? Please explain. Thank you so much.
Tried using 9v but not working properly..
Hlo brother I have some problems in my car can you solve it plz
how we can do this by using simulation i.e software model only?
what is AFmotor.h...from where do we get this file...please help
Great job!
Plz Make a tutorial on how to setup Bluetooth controller app for this project!
Bro will it work on lithium ion batteries
Which app you use voice cammond the link of app that you give in description is not for voice commands.
Which app u used for voice
play.google.com/store/apps/details?id=com.broxcode.arduinobluetoothfree
Where this battery available
Bro can we convert this car into voice control camera car plzz tell me
Can we installed the code aurdino before any wiring
Just remove tx and rx pin of Hc-05 while uploading the code
@@hobbyproject
Hey,first we upload the code and then we attached the aurdino in the car.it will work or not
Yes it will work.
@@hobbyproject thank you
9400496834 wts app
How to download this control car aap piz cmt down
Can i give 4 battery??
Bro you have done a nice work . And I have tried as you said but the car is not moving can i expect any help from you bro....plz bro
Sure, send me your what'sapp number
you have gave 2,3 code so i am confused
please sir can u tell me why did u add
unsigned char velocidade1=0*00;
unsigned char velocidade2=0*00;
unsigned char velocidade3=0*00;
unsigned char velocidade4=0*00;
in the code
Without this code cannot be uploaded
But sir we did not use it!
But it showed error while uploading without this
Ok thnks sir
Another question sir please what is the difference if we add a servo motor ?
Need to change the code and include servo.h library
Can we use normal DC motors instead of BO motors with the same code?
Please reply
Yes
Kya gear motor simple gum se chipak hai
Bhai yah kisi ki bhi voice se chlega kya ya sirf meri se
18650 3.7v 2000amh is used or not
Yes u can , 7.4 v required
problem in coding
bro codding ma problem a ra ha plz help
What's the problem ?
Link for pin headers
Bhai wiring description me circuit diagram Mese karni he Kya please bata de bhai replay de jaldi 🤔🤨😅
What problem ?
@@hobbyproject circuit diagram
Ke under se wiring karu Kya
Yes. Follow the circuit diagram. Any doubt ask me
@@hobbyproject or code bhi description me diya he use upload karna he Kya
Yes, Af motor and softwere library also required
bro code not opening bro...so give me saparately ...its urgent plzz
drive.google.com/file/d/1D7ydEJ4yIBX9WbvcaDoq7dz45jWd8hI4/view?usp=drivesdk
How much volt battery required for this operation sir... Plz say
I have used two 3.7 v 18650 battery in series
Instead of two can i use 1
How much volt is necessay
7~12 volt
Can we use Arduino SMD Version ?
Yes u can
Can we use 180 motor plz tell will it work
No..Motor's with 100-500rpm wil work fine
Why not 180 plz tell
If we use 180 then it will be fast
Yes that's the reason. 180 motor are used for drones or flying applications
180 motor ko chalane k liye koi controller chahiye
bro give the software link
It's available in the description
I have araudiano IDE on my laptop but I want the blootooth application for connecting my robo
Ok . Now i just given the link on description please check
@@hobbyproject thanks sir
Can i use l298 motor driver
Yes, But you need to change the code
coding kase karo
What weight bear this car
~1/2kg
Will this code and wiring work for different parts
No
I’m planning to make this for a project so I have to buy the exact same parts
Yes (Arduino,shield) same required for this code
Is the 12v battery will work ??
What type of battery?
@@hobbyprojectits an lead acid battery
No . 7 to 12 volt below 1 amp is required
Plz relpy bro
9400496834 wts app
Agar 300rpm ki motor use kre tho
No problem
Bhai agar l298 use kre tho
Code ko change karne padega.
Tho kre ke bhej de na bhai
Bhai af motor ki jaghe kyalikege
Bro I need code
Can u send the code haa bro
Check description .
What's your Instagram id
👌👌