The potential is not on cleaning. The potential is on old peeling wood houses--especially, with a 4 gpm 4000 psi setup. Painters don't realize that chip blasting is all about the angles, and a narrow stream that doesn't pin the chip into the house from atomized water, when you are trying to remove it. I nearly patented this design in 1996, but didn't have the money for the prototype and patent. A 4000 psi unit is fine for and initial pole pre chip blast. But this would make a great second , short pole pass. The third pass should be still made with a low psi fat roto blaster, slightly over speced on orifice, for a surgical puzzle blast. Then grind or sand to make wood paintable.
Hi Phil, at £1400 a pop I would be very interested to hear what you have to say after you have used it on a few different surfaces of varying dirtyness. I am getting a new van with a tank a pressure washer and a pressure hose reel in the next couple of months and will probably go for one of these next year depending on what people say about it. Keep up the good work man.
Jesmond Jetclean £1400 try closer to £1700 lol. they are around £1400+vat first impression is awesome. well engineered. quite heavy by itself but becomes quite well balanced once attached to a lance and trigger. hoping it is going to tear through dirty block paving.
Hi Phil - it's Peter from Newcastle. Anything to report? I am dying to hear how good this is! I agree Wolf tools all the way - I find the whirlaway to be not very good but when it is good enough it is diamond.
Jesmond Jetclean hey jes, yeah it's an awesome tool. Tears through block pave like you won't believe. Really need a 250bar min coz if you wind the power down it doesn't cut through as well. Video of it will be up soon. Phill
Full face guards are the best, flip up and down, most common for grass cutters like you will see some council workers using with a petrol strimmer, easily found on the usual sites
After having it for a few years, it's not worth the money, costs too much to service every year. Nozzles are proper pricey at around £200 a set and falch aren't very nice to deal with. It's a great tool don't get me wrong but falch are so stuck-up that it's painful to deal with them.
cal ram if you had around 500bar and about 40lpm machine with around £3300 to spend I'm sure you probably could. But trying to run 2 on a normal machine would be pretty much impossible as you wouldnt have enough pressure or flow to spin them up.
Hi m8 thanks for the reply, i'm currently using double nozzle lance with two 07 turbo nozzles 250bar 55ltrs min , just wondering if the falch would fit side by side on the double nozzle lance, as you have both the falch nozzle and the double nozzle lance, you would be my best bet of having an idea if they would fit.
Ăn chơi không sợ mưa rơi quá đả Only available from Falch direct at a cost of £1640. You cannot buy it on a website you will have to make contact with the sales team at Falch.
It's a great tool but not worth the money. Don't think they sell them in the US as they don't have distribution/service centres. Had several people say they can't get falch stuff over there.
God knows, well overpriced to be honest. Was wicked when I bought it but it needs servicing every year and that costs £300 and that's without new nozzles. Its an awesome tool, it's quick and powerful but it needs maintaining.
If I liked walls and non demonstrative demonstrations, this would be a good video. As it is, I have decided that I will never buy a Falch Pointspeed 5, as it clearly has no demonstrable benefits!
Well as the title says its a quick demo for my subscribers who wanted to see the nozzle working. If you want to see it in action look at the other video.
The potential is not on cleaning. The potential is on old peeling wood houses--especially, with a 4 gpm 4000 psi setup.
Painters don't realize that chip blasting is all about the angles, and a narrow stream that doesn't pin the chip into the house from atomized water, when you are trying to remove it. I nearly patented this design in 1996, but didn't have the money for the prototype and patent.
A 4000 psi unit is fine for and initial pole pre chip blast. But this would make a great second , short pole pass. The third pass should be still made with a low psi fat roto blaster, slightly over speced on orifice, for a surgical puzzle blast.
Then grind or sand to make wood paintable.
Where did you buy this from Phil? Thanks Rob
Rob Broley you can only get them from falch. Will cost you £1640.
Hi Phil, at £1400 a pop I would be very interested to hear what you have to say after you have used it on a few different surfaces of varying dirtyness. I am getting a new van with a tank a pressure washer and a pressure hose reel in the next couple of months and will probably go for one of these next year depending on what people say about it.
Keep up the good work man.
Jesmond Jetclean £1400 try closer to £1700 lol. they are around £1400+vat first impression is awesome. well engineered. quite heavy by itself but becomes quite well balanced once attached to a lance and trigger. hoping it is going to tear through dirty block paving.
Hi Phil - it's Peter from Newcastle. Anything to report? I am dying to hear how good this is! I agree Wolf tools all the way - I find the whirlaway to be not very good but when it is good enough it is diamond.
Jesmond Jetclean hey jes, yeah it's an awesome tool. Tears through block pave like you won't believe. Really need a 250bar min coz if you wind the power down it doesn't cut through as well. Video of it will be up soon. Phill
Hi have you got any advice on a good face mask for doing block paving .
houstyful to be honest I don't use one. I just use a good pair of safety glasses.
Full face guards are the best, flip up and down, most common for grass cutters like you will see some council workers using with a petrol strimmer, easily found on the usual sites
Is it worth it compared too normal one? I do mainly roof cleaning, time is money.
After having it for a few years, it's not worth the money, costs too much to service every year. Nozzles are proper pricey at around £200 a set and falch aren't very nice to deal with. It's a great tool don't get me wrong but falch are so stuck-up that it's painful to deal with them.
Nice turbo nozzle! Should there be water leaking from the nozzle ?
Yes, it's designed to have a small amount of leakage, this keeps the bearings cool.
That leak on the rotation tip...is that normal?
Radhwan yes, they designed it like that and prefer a small leak as it keeps the bearings cool.
Hi m8 could 2 off these fit on the double nozzle lance.
cal ram if you had around 500bar and about 40lpm machine with around £3300 to spend I'm sure you probably could. But trying to run 2 on a normal machine would be pretty much impossible as you wouldnt have enough pressure or flow to spin them up.
Hi m8 thanks for the reply, i'm currently using double nozzle lance with two 07 turbo nozzles 250bar 55ltrs min , just wondering if the falch would fit side by side on the double nozzle lance, as you have both the falch nozzle and the double nozzle lance, you would be my best bet of having an idea if they would fit.
cal ram 55lpm how the hell do you keep you tank topped up, but no 250bar is not enough pressure to power 2 nozzles and they are £1640 each.
ok thanks, m8, I hire standpipe of the Scottish waterboard, pity about the pressure these nozzles look superb
cal ram they are but bloody expensive.
Sorry to ask were can I get price for this please
You can only buy them from falch direct and are around £1640
Is this your only job does pay you enough to be off work in winter mate
Yeah. I make enough.
Great mate good videos I learn a lot from you
Can you show me the website sale like your nozzle Please ...
Ăn chơi không sợ mưa rơi quá đả
Only available from Falch direct at a cost of £1640. You cannot buy it on a website you will have to make contact with the sales team at Falch.
Honestly.... a totally unnecessary item..
I want this nozzle how much price ? I am from India
I dont sell them
how much is that? ?
where can you buy 1
You can only buy them from Falch direct at a cost of £1640.00
Dirty Drive-Away Really ,why so Pricey ££££
Steven Douglas typical German engineering and price tag lol
@@DirtyDriveAway 🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣
2k us? Wow. Is it worth it?
It's a great tool but not worth the money. Don't think they sell them in the US as they don't have distribution/service centres. Had several people say they can't get falch stuff over there.
I have turbo nozzle I live in Indiana
How much is this tool ?
Around £1700
How much is it. I need 500 bar
Cuong Nguyen it's £1640.00 GBP. It's rated for 500bar max.
4million 🎉🎉
Top speed is
Noooo,noooo,noooo your quick wideo dosnt show any cleaning action,did ya? No
I know, the video Is a quick demo of the nozzle. There are plenty of other vids on my channel with this nozzle in action.
Why is it so much
God knows, well overpriced to be honest. Was wicked when I bought it but it needs servicing every year and that costs £300 and that's without new nozzles. Its an awesome tool, it's quick and powerful but it needs maintaining.
If I liked walls and non demonstrative demonstrations, this would be a good video. As it is, I have decided that I will never buy a Falch Pointspeed 5, as it clearly has no demonstrable benefits!
Well as the title says its a quick demo for my subscribers who wanted to see the nozzle working. If you want to see it in action look at the other video.