Valve Adjustment on a Chevy 235
HTML-код
- Опубликовано: 8 сен 2024
- Valve adjustment on a 1961 Chevy 235, inside of a 1948 Chevy German helmet. Victory Auto finished installing a full custom wire harness, 2 barrel carburetor and other miscellaneous repairs.
After getting the car started up for the first time, we realized how rough it was running. After some troubleshooting, he quickly found that it needed a valve adjustment because the pushrods were previously replaced.
This is our first youtube video so be easy on us. If you have any questions, or need clarification leave a comment down below.
FOLLOW US ON INSTAGRAM:
Gabriella - / gabriella.delcastillo
Victory Auto - / victory_fleetline
Blvd Detailing - / blvd_detailing
Just a comment from an old man who ran a garage for a living. Stove bolts inline sixes don't have to be noisy. The problem with the procedure you show is there is a drastic temperature change from the start to the finish. If your settings don't allow for it there will not be accurate. my procedure is getting the engine running and able to be loaded as in driving or cruising in a marine application. Shut it down and then check and set the number six-cylinder valves, they will be the hottest. Set the valve cover back on and wait till morning then measure the valve setting on number six cylinder. This is your cold engine setting. Use that to set the valve without temperature change for a more accurate setting. If you want it quit running reduce the settings about 1 or 2 thousandths. Tighter the settings the less wear takes place in the valve train and longer before needing adjustment. But hey I'm just a old, retired mechanic who worked on these for a living.
I want to compliment you about the quality of work you preformed on you magnificent car. Its a winner in any show! Be proud of your accomplishments.
Great video, thank you for posting. It is nice you are sharing your knowledge with us and your girl !
Very knowledgeable...great job!
Thanks you for sharing on 235 ,it helped me with my 53 /210 . Looking for more videos from you 😊
I am learning this stuff right now and I'm in my 40's. It fun. I enjoy the old cars. Yours is sounding really good 👍
Once it is set to TDC Did you adjust all valves without moving ot off of TDC??
I had that same Weber setup on my 235. I ran it for a while and then went back to the stock Rochester. I got better gas mileage, but the engine suffered a very noticeable power loss. I found out later that the Weber is only a 200 CFM carb. I’m now going to put that Weber on a 216 since the stock carb is long gone. It will probably work better on a smaller motor. You have a nice looking car.
I read that if you’re adjusting them cold add 2 thousands so they won’t be to close when hot. I’d check while hot to verify
I hope you make more videos because I really enjoyed this
My cousin who was a "stove bolt" savant would adjust the valves by making the engine idle down to about 450 rpm and adjust the valve while it was running. As some as the engine missed he would loosen the screw a bit then tighten the lock nut.
I never heard of anyone adjusting valves while the engine is running.
Good Job, pls keep at it!
great info. Like to see more.
Enjoyed this. At 85 knee these firsthand.
Thanks for the valve position lesson and reminding me I'm a dummy😅
Thanks for this. Did you swap to 12v? Do you use electronic ignition?
Is that a Weber 32/36 carb?
Were you running a one barrel or a two barrel carburetor
Are you turning the air/fuel mixture screw towards the end? Also, are the gap specs different for a mild cam? Thanks. Great video
What carb r u running on the 235 ?
i do mine wile the 235 is running much easyer
Unfortunately I’ve seen other mechanic damage valves that way. When you’re getting paid to adjust someone’s valves, doing them hot with the engine off, per by the book is a more accurate and safer when you’re working on cars that arnt yours
One question what carburator is using on your engine???
Que chingon!!!
Bro I’d to take my truck to you, where you located? Thank You
Buenas tardes me puedes decir cuanto as milésimas debe llevar el ajuste de válvula de agnición y existo de un motor 235
Buenas noches pueden enviarme a que orgura calibraron las válvulas de admisión y escape
Thanks. Where yall @ ?
My shop is in La Habra now
Can you hook me up? I got a 51 chevy styleline 216 . I'm in S.D. nice work . Learned alot
Everyone usually does their 216 at exhaust 18 intake 6 never'd hurt anything
Never came across anyone doing at 216 at .018” exhaust.
.013” exhaust is the correct adjustment for 216’s. Not 235’s.