Hi bro,please make a video on how to connect it with exaust fan in the kitchen to start automatically detecting by smoke ..my mother suffering a lot because smoke..
Why mine does not work . Trust me I follow all steps exactly 100%wring,etc ... 1.My sensor works when I use Arduino uno . 2. Does not work when I didn't use any micro controller. . Any speculation s why mine does not work???
I bought 2 of this MQ6. I thought 1st one is broken so I ordered another one. Turned out that both are working fine. To get it work without Arduino, make sure you battery is not drained out. Same wiring as the video. But when connect a buzzer, you'll probably hear long continuous beep from buzzer. This is the reason I thought mine is broken. I immediately remove the buzzer and assume it's broken. Actually you should let it beep until it stops. Mine take around 9-10 seconds. You'll probably see green led come up on one side of the module. Adjust the potentiometer until the green led goes dark. Now test the gas sensor with cigarette lighter. I finally got both sensors to work. Hope you get it work too.
Can we use adjust fan with this same volt and sensor
Sir MQ135 gas sensor ki power Light hi nahi jal rahi hai kiya problem hi..
Mai connection proper kar raha hu phir bhee.
Can you add motor also for this project if yes please reply how to add motor
Hi sir
At last of the video u have tested the device whether its working or not what kind of lighter did you used sir
Hey can we also use normal connecting wires instead of those clip jumper wires pls reply?
Yes. You can also use normal wires.
Can we use mq2 with 9v battery?
Yes
Can we use led
Sir can I use it for making fire alarm?
Yes you can
Can we use mq6 sensor
Yes
Hi bro,please make a video on how to connect it with exaust fan in the kitchen to start automatically detecting by smoke ..my mother suffering a lot because smoke..
I have purchased a li-ion cell battery will it work for this project ???
Just try. It should work. I haven't tried with that.
@@TechTrendsShameer thank you very much for replying 👍✌️😄😃😀
Which sensore it's?
Gas Sensor
Shameer Sir, please share the Circuit Diagram...... sir Output wire connected DO or AO..... sir please reply 🙏.....
Can you please check the video and check which Pin I mentioned?
! ?
Can i use normal wire
Because i have not jumper wire
Yes you can use normal wire
Sir, apne lighter ko kese modify kiya h, matlab vo only gas kese spray kar raha h...
What is the code of the gas sensor
Can we use 3.7 volt battery
Yes.
Sir ye pura saman kaha par milega please help me
Check video description
sir can we use alcohol sensor in place of smoke sensor
Yes
Bor i make this project connect the battery buzzer automatically alarm .pls help me bro Monday i have submitted the project fast bro pls
Sir entha conting wirse set pannalama
Question puriyala. Please make it clear.
which gas sensor did you use mq 6 or mq 135 or another one
MQ 135
www.electronicscomp.com/sensors-module/sensors/gas-sensor/mq135-air-quality-gas-sensor-module-india
I am having mq2
@@TechTrendsShameer can i use mq 2
@@TechTrendsShameer Sir, please share the Circuit Diagram...... sir Output wire connected DO or AO..... sir please reply 🙏.....
Sir I can't reach the website
Can I use 12v supply in VCC
Please check the specification of your device before you use.
The smoke detector beeping when there is no smoke. What is the problem .
Isn't there any mistake in connection
Can you respond faster
Can change the amount of the potentiameter
Sir it is contineously ringing
same here even without gas
Bhai 4 sensor use kare tab bhi chale jaa rha hai
Amazing all other videos were shwoing with useof the arduino board helped alot for my school project
Thanks a lot. Keep supporting.
@@TechTrendsShameer do you know how to split 1 9v battery to 2 sets of cables
@@TechTrendsShameer
Can i use mQ6
Yes you can
do i need male to male of male to female cables
You can use female to female or female to male wires. Then cut the pin from one end and take the wire out. Connect that wire to the battery and buzzer
@@TechTrendsShameer thanks for telling me!
Its ok sir, but how can use it longtime?
Does it work with Incense
Just try it
I tried this but tge buzzer keeps turning on anytime i connect the battery without any smoke, please what can I do sir
Yes sir please reply
which lighter did you use
Gas lighter
Please send the photo of gas lighter
Can I use MQ-2 sensor
Yes. You can.
Not working 😂
What's the problem
can i use mq5??
Yes
hello, why mine keeps ringging even it don't have smoke plsss help mee
Does it work on match smoke?
Yes
Sir mera to buzzer hi sound nahi kar raha hai please help me
Please check the connection.
@@TechTrendsShameer sir check kar liya phir bhi buzzer baj ra
@@TechTrendsShameer connection aap hi ki jesa h
I LIKE PROJECT
Thank you
SIR can i use a 3 volt battery?
Try 9V battery
Where can i get 1pin connecting wire
sir ye gas sensor 9 volt ki battery me heat ho ja raha he is liye properly work nahi kar raha he
SIR WE WANT SMOKE DETECTOR PROGRMMING
CAN U PLEASE HELP US
You can contact with me, i can help you with programming
mine is working without the smoke or gas. any suggestions to fix it?😊
same here
Not work sir kyonki sensor ka dono light chal raha hai or adjusts karne par bhi band nai ho raha
Bhai mene apke jase he wire joda hai per mera buz nahi raha hai mera school project hai please help kare do
Great project 👍
Thanks you so much.
Sir liter me fire kyu nahi nikal rahi h, sirf gas hi leak Ho rahi h apke kese
I gave all circit connection but it din t give any sound
Thank you sir i did this project for my chemistry and got gud score 👍
Great. Thank you. Please subscribe
Sir mera to buzzer hi sound nahi kar ra please help
Mujhe koi batao ye sman kha milega
Bhai mera work hi nhi kar rha hai
அருமை யான பதிவு ஐயா செ ஆனந்தன் விஞ்ஞானி இந்தியா
Thank you 😊
MQ6?
MQ135
How to make with mq 5 gas sensor
Replace the sensor
I used mq-6 but it's working by fire not by smoke
Try with MQ 135
Without smoke also buzzer is turning on
Same
Bang kalau pakai 3.7vol disa enga yah bang
Has dector 🔗links
Will it works in 9v buzzer
Depends on battery power
So you mean less power
Yes.
I am faling to make this becouse without sensing buzzer is going on ringing
Can you please send your code?
Same issue
Sme issue
What number of MQ gas sensors did you use?
MQ 135
www.electronicscomp.com/sensors-module/sensors/gas-sensor/mq135-air-quality-gas-sensor-module-india
@@TechTrendsShameer can't we use mq2 sensor?
Mq4
Sir I can't open this website
Sir
Mera Bina kisi smoke ka hi aawaj kar Raha hai
Check your sensor
Can I get circuit diagram
the MQ6 needs 5 volts not 9 volts
Did you install codes in the sensor
No need to install any code.
Not working 😡😡😡😡
Skill issue
Lol😂
does this also work with other detectors
yes
Why mine does not work .
Trust me I follow all steps exactly 100%wring,etc ...
1.My sensor works when I use Arduino uno .
2. Does not work when I didn't use any micro controller.
.
Any speculation s why mine does not work???
There is a potentiometer on the back side of sensor. Can you please adjust that and try ?
@@TechTrendsShameer clock wise or counter clockwise??
For highest sensitivity.
Please adjust and try. Sorry I am not sure.
I bought 2 of this MQ6. I thought 1st one is broken so I ordered another one. Turned out that both are working fine.
To get it work without Arduino, make sure you battery is not drained out.
Same wiring as the video. But when connect a buzzer, you'll probably hear long continuous beep from buzzer. This is the reason I thought mine is broken. I immediately remove the buzzer and assume it's broken. Actually you should let it beep until it stops.
Mine take around 9-10 seconds. You'll probably see green led come up on one side of the module. Adjust the potentiometer until the green led goes dark. Now test the gas sensor with cigarette lighter.
I finally got both sensors to work. Hope you get it work too.
@@jumbo999614 punya Saya hidup terus bang? Ini harus bagaimana
Not working😅
Not working😡😡😡😡
Bang kok gabisa
Can you please reply
Which sensor you are using?
Not working, aap galat wiring kar rhe ho, aap fake video bnate ho
Sur please reply quickly
It is beeping without sensing smoke 😡😡😡😡😡
Kis kis ka kam nahi kiya
Check the video
Fake video 😡😡😡😡😡😡
😊😊
The buzzer is ringing without sensing the gas
Which sensor you are using?
@@TechTrendsShameermq 5 sir and it's ringing continuously without smoke also plz reply fast sir it's urgent
Fake 😠 video , not working 😂
Not working
may i know the error ?
Sir ple u are cell no
Sir my buzzer is continue ringing why this happen
Yes same pls reply
Fake
If you didn't got output that doesn't means video is fake. Try with good components.
This is waste worst 👎👎👎👎👎
Thanks for your compliment. BTW can you show your good work ?
Bro l did this project about when batter is kept automatically buzzer is ringing .Bro give me your number
Thank you sir this is work ❤️🫂
Not working
Not working
Not work
Not working