Litter Robot 3 Open Air Troubleshooting - All 3 Lights Flashing - Floppycats

✅ Litter-Robot 3 Buying Options:✅
💵 Worried about your cats using it? Want to be able to return it without paying for shipping?
😻 Buy on Chewy - Get 24/7 Help + FREE 1-3 DAY SHIPPING:
bit.ly/395ovFR
🤑 Buy the Litter-Robot 3 Connect on Amazon: geni.us/H1EB [Amazon]
💳Furthermore, Litter-Robot offers bundle deals often including a new Litter-Robot and accessories at a reduced cost. We email our readers when they are offering bundle deals - sign up for our newsletter here: www.floppycats...
If the Litter-Robot 3 cannot find Dump and/or Home position, the control panel will display 3 lights blinking. If you have recently disassembled your globe, please advise.
There are a few reasons why you could be getting this error message. We will touch on each component.
PLEASE NOTE
If your unit was purchased on or after February 21, 2018 (Serial Number 078843 and above), your unit will not have an internal shield. It will, however, still have the black key on the back of the globe. If you do not have an internal shield, please disregard the shield instructions (first video link) in number 3. You may still check the key/spring (second video link).
1. Excess Weight
If there is excess weight inside the unit, this will cause the motor to slow down and the unit will not complete a cycle in the allotted timeframe (~2 minutes, 45 seconds). Please check your litter level to ensure that you are at or below the fill line. If necessary, remove some litter from the globe so that the level is an inch below the fill line, then press the Reset button. It's best to empty the waste drawer as well if it's getting close to full; this will eliminate that excess weight also
2. Power Supply
Please check that the adapter you are using meets the specifications required: 15VDC regulated adapter 400mA to 1000mA.
Please make sure there is no damage to the power cord.
If your unit is plugged into an extension cord, please try a wall outlet to see if this makes a difference.
There is also a pin inside the jack on the base. It should have a split in it. If there is no split, I recommend splitting it open with something small.
3. Internal Shield/Key
If the internal shield or black key isn't set properly, this will cause cycling issues. When your unit is in the home position, the shield should be in the top left corner and the key should be straight up and down sitting in the groove of the base.
Below are two videos that show you how to reset the shield and key if necessary.
Key/Spring: • Internal Shield Remova...
Another option is to remove the internal shield. The internal shield is not necessary for the unit to function. To remove the shield, you will need a Phillips head screwdriver. Remove the screw from the center of the black key on the back of the globe. Once the key is removed, you can easily pull the shield out from the entrance of the globe. If you decide to remove the shield, please let us know and we will send you a key-hole plug for the back of the globe.
You can see the video on how to remove it here: • Litter-Robot 3: Removi...
4. Bonnet
If the bonnet is not seated properly, this will cause the unit to start and stop during a cycle. To make sure your bonnet is seated properly, please follow these instructions:
Disconnect the bonnet
Gently flex the two front bonnet tabs outward as close to a 90-degree angle as you can and hold for 20-30 seconds. This will remold the tabs to have a more secure connection.
Reattach the bonnet. There are four tabs total: two curved tabs in the back, two on the sides. The two curved tabs in back tuck into slots in the base. If they are sticking out, the unit will not cycle properly.
You should feel a secure snap and hear a solid “click” when placed back into the slot and the bonnet should sit closer to the base.
Assembly Instructions: support-litter...
Video of removing/replacing bonnet: • Remove and Replace the...
5. Globe Lift
If the globe is encountering resistance that is lifting it out of position as it cycles, friction will occur between the plastic of the globe and base, causing the magnets in the globe to skip the position sensor which will cause the 3 blinking lights.
Out of the box, the Litter-Robot has a silicone lubricant layer that can wear off over time. An easy solution to this is Pledge Furniture Polish (if you have a different brand of furniture polish, it will work as well). We would ask you to please simply spray the polish on a paper towel and wipe the track of the base where the globe sits. Please avoid getting it on the black gear. I have attached a picture of the track of the base for your reference.
Always remember to press reset after making changes to the unit. Run a few test cycles by pressing the cycle button.
Litter-Robot
Have a question? Contact us!
Phone: [phone] | Hours: 9am - 7pm ET
Email: [e-mail]