How to increase bass on subwoofer Make speaker louder and high bass
HTML-код
- Опубликовано: 10 сен 2024
- How can you increase bass response from your amp and subwoofer. Tips on boosting bass for subwoofer. The simplest is to use an inductance from 1000w to 2000w or 3000w depending on speaker power with amplifier.
Use an iron screw as the core to wrap the inductors, since I was the first to detect it to increase the uH value. You will change the frequency so that the bass sounds better. Applies to both subwoofer
Channel: Alfred
Google+: plus.google.co...
facebook: / thanhhai.bui.58910
Yeah, we quite using choke coils in the 90s when active crossovers started being standard on amplifiers. Also, properly made "choke coils" ( passive lpf) are about 5 bucks at Radio Shack ( if u can find one anymore lol)
So i tried this and apparently it also works as a flux capacitor cuz when i was driving dowm the freeway and hit 88mph i got sent back in time.
oh ...
Go back in time and smack the camera outta dudes hands
clearme2. Hahaha
Does driving backwards at 88 mph send you into the future then?
Errr... I shouldn't of fallen asleep during the second movie..
So you got sent back in time? Whats the future look like? Does someone shoot Donald Tramp soon? Please say yes. Please please please pl....or did u go back from the present? Talk 2 me....tell me sumpn good....lol
really nice presentation that delivers the idea easily to us.
straight to informational thats what i like
who has studied electronics can not accept this video as a tutorial.
It is unthinkable to do such a thing.
plz explain
could you explain why this will no t work or shouldn't work? thanks
Elettronicalab roma yes
Yes explain??
really? emf and how sound wave change to electrical, learn it
Alfred Thanks buddy, that's using the head, since there are those who say, easy: you buy an amplifier and you're done
Thank you more
By putting a coil in series with the + lead, will only cut off the higher frequencies. You can put a capacitor parallel (over the + and -) to the speaker, to obtain the same effect. The use of (silly) thick wire for your coil is merely to dissipate the high power input.
High frequency cut-off applies to bass speakers that do not apply to full-range speakers
Frequency response for heavy bass is from 22 to 800Hz. The lower the bass range, the better the bass.
The fact that you add a capacitor connected in parallel with the speaker is sometimes a burden on the amplifier and the sound is shaken
Therefore, if you choose the wrong capacitor value will get the opposite effect.
but inductors are indispensable
You seem to know alot budddy 😅 I have a small 4inch Bluetooth speaker and I have a 10inch speaker.....I want to take both of those subwoofers and connect them to a Bluetooth receiver powered by one 18650 battery
Will adding another 18650 provide enough power to both subwoofers?
Can I boost my bass using this method?
@@imraankamish8220 Those are questions which take no easy answers.
Your BT receiver circuit is powered by 3.7 V (it seems). Placing another 3.7 V battery parallel almost doubles the time one can play; it does not double the output power. You can not place the batteries in series (making it 7.4 V); the receiver circuit will probably die.
Two 18650 batteries parallel will make the receiver circuit (and probably the bass) work a lot easier, with better sound.
IF YOUR INTENSIONS WERE TO INCREASE THE VIEWS OF YOUR CHANNEL, THIS IS THE CORRECT WAY.
But people who really understand what a real SUBWOOFER is, know that to use it, you have to use amplifiers that already have filtered active crossover outputs in the amplifier itself (possibly with low frequency boosters and subsonic filters).
What you did in this video is nothing more than a first order passive low pass filter (with a cadence of 6db per octave) that does not eliminate any unnecessary frequencies, but only attenuates them.
It follows that the concept is totally wrong, because if the intention is really to increase the bass produced by the subwoofer, you simply need to change a subwoofer or amplifier.
Frequency range of bass from 22hz to 800Hz. The lower the frequency band, the stronger the bass
The frequency range of the midrange speaker is 5000Hz
Frequency range of high frequency speaker is 13000uH to 20000Hz or even 40,000 Hz
There are many different types of speakers
Each type of loudspeaker will operate at different frequencies except for full-band integrated speakers
In the amplifiers, the manufacturers did not make filter circuits for the speakers. The simplest reason is that the amplifier should be suitable for use with a wide variety of speakers at different frequencies. If the amplifier uses frequency filter, Amplifier will not be used for many other types of speakers.
So in the amplifier they only make a preliminary filter circuit or not even do
Therefore, using a high frequency cut-off coil is appropriate
Here want good bass you have to adjust the coil
Electro Maniac pretty much my thoughts. Then his response lol... has nothing to do with what you said really. Just started talking about frequencies... it's like ok doesn't change the fact that all you did was make a ghetto rigged crossover lol.
Or just get an actual passive sub crossover, or an active crossover in front of your subs' amp
Electro Maniac d
Electro Maniac valiem controler
The symbol looks messianic as well as the music. I've seen many of those freemason warning videos with that creepy music and symbols.
How did you manage to screw it up so badly, that your low pass filter appears to increase the higher frequencies?
The reason is that you can not close the windings close to the magnet of the speakers. It will affect the magnetic field
The main reason is the iron screw. Without it, the Henry number would not be as desirable
A LPF crossover is either made using a capacitor and a resistor (combo1), or it is made using a capacitor and an inductance coil (combo2). Whether you need combo 1 or combo 2 and what the values of those parts need to be will depend on the type of driver, it's frequency response range, ohm load, and possibly a few other variables i may not be thinking of.
There's some formula to use speaker parameters to make the ideal crossover but there's a way to get the right sound out of a given speaker
it's a 4 to 1 Baland.. learn your electronics
@@jymnazium8312 or BALUN, learn your components
I just keep old inductors and capacitors from old speakers or amps I throw away. Sometimes they're blown Alon with the speaker but I get alot still good. They're fun to screw around with
No coil= beats
With coil= full beats
Cool
I have a tutorial for increasing bass too. I titled it: Buy a bigger amp or bigger subs or better box or moaar of everything.
Thats where all my old car and boat parts went...... Recycling in action folks!
Like a booster for sound speaker.
Hmmm..
Must have more energy
why do you say that
@@AlfredH fact
Wow you made an inductor, now make a capacitor and you can filter at 12db an octave. Oh and you didn't make it louder but slightly quieter due to resistance.
you are right. Inductors will cut the high frequencies, which will reduce the treble and mid to make the bass speakers work better. The bass will be clearer
It does not make the sound louder. But the amplifiers are now too strong, so the diminishing of a bit of db to better sound is not too much influence.
I will add a capacitor to filter the lower frequency.
mark Andrew
Back in the days those was know as choke coils.
sangam killer
Ff
How come no one seemed to notice the fact that this arrangement can never achieve high fidelity results simply because he made use of bolt and nut which are both solid iron blocks instead of a ferrite as the core material for the inductor,the hysterical and eddy current effects would affect the output somehow at certain frequencies
So you put a 6dB/oct filter on it? WOW! Much shocking. Very bass!
If your going to create a tutorial like these.. You should see first and understand the importance of voice coil and magnets. The answer to high bass is good speaker cone, thick and flexible...
what happens if the answer is a thick speaker?
Muito bom parabéns pelo trabalho meu amigo
The title need to be called how to make a low pass crossover... But click bait is better tho
Sir aap kis wire Ko roll karte hai
Nice job
I'll try making my own passive crosover thanks for the
thank you
Have you figured out how to do this properly yet?
i dnt believe on this method!
this could damage your ampli output on high volume!i rather used the original speaker from the specs factory.and use a high watts ampli to fullfill the speakers..jst take note on the specs of the speakers!not to overdrive it!😎
Can someone explain how wtf does that have in common with a low pass filter
click bait 101, that's what the title should of read. If the person responsible for this video believes any of this garbage than said person would benefit from some basic electronics tutorials found anywhere.
What is it, you say more clearly
What is the component used to make choke coil that burnt by fire
where did your 3rd nut go? It must have left with the increased bass!!!
William WilliamM lmmfao!!!!!!
William WilliamM no
I think the 3rd nut stayed to the end of the video 😂😂
Well, 2275hz cross with 4ohms is really bad for speaker this size.U should make coil 3mH imductance (large power losses) or just apply an active crossover.
What's the copper wire bolt end connected too?
Is not correct. 1.8mm are equivalent to 2.54mm2 of section, for 3000w in 8 ohms you need to pass 19.36 Ampers through the wire, if we divide it by the section, it results in 7.62Ampers x mm2, more than double the recommended 3Ampers to avoid heating and distortion. On the other hand, the bolt is made of steel and has high carbon levels that do not favor magnetic permeability with great losses, an electrical silicon steel must be used.
Speaker build quality matters
Haha... yeah, that will work. However, it's pretty much the worst way to achieve your goal of delivering more bass. You're using an inductance to basically throw away (as heat - which is why you need different wire guages for different power levels - these things would otherwise melt!) some of your mid-bass signal that your amp was working hard to create, using a 1st order low-pass. Of course, you are now left with more of the low bass, and if you can turn up your amps to compensate for the lost mid-bass, it'll feel "bassier". However, it's SO much easier to do the same (should you desire this) before the amp... Simple bit of equalizing, a tiny bit of a capacitance across an opamp's input, and you're there. Components that cost like 50 cents at most. And the result is, you're not throwing away any of your amp's output. I don't get why you'd do it this way, unless you were hard-pressed for bass and didn't have access to even the most basic electronics supplies.
decnet100 so can u explain what you would do again?
i dont know dude may be you should try flipping the speaker over, or placing it over a speaker box or better yet play some music with real bass. then we see if that contraption you got there works or not?
how can you increase the bass with that thing? :D explain it, :D
*_VERY GOOD WORK_*
thank
Its amazing
Có phải anh Bùi Thanh Hải phải ko em đoán 100%la
i had tried this too and the bass of the speaker really increased.. however the overall sound decreased... i used a thin copper wire with more than 200turns an almost 10mm diameter
The overall sound is reduced a bit, since that is the filter. In return, the sound is clearer. If your amplifier is high, it will not matter. You may have to adjust the volume up
You can watch other similar videos talk about this in the channel
all you did was make more of a filter that will take any nose out of using any crapy wire. now if you add a compositor of the right size acroww the speaker turminals that can boos bass but only in the cense it will buid a voltage and give a little more power when needed to make it a more constent power.
good night I really liked your video you can give me the specifications to do it at home thanks
The specifications are as in the video. As the quality of the screws is different, the value of the HenRy changes
Good to know the trick it come handy one day
thanks so much
you made a crappy cross over sooooo ?????????????
Where is the battery now?
to add trible sound just used capacitor in series connection
I will work in 5w and 9w woofer?
70 ya 100 watt ka configuration kya hoga sir..?
that's how stuff works in the place you come from...
The lighter to the battery part was SO cringy
At the very least this choke coil focused and used the power for low negative bass which sounded better on that little speaker that cant handle high positive bass, this might just work, if your desperate for low bass, I love my lows, worth a shoot on littler systems, like my 8 inch Bluetooth build, everythings perfect pit capacitors for highs tweeters, got a mid speaker and a 8inch sub that I need to only get mostly lows out of, if anyone knows a more efficient way for my setup, please message her.
Don't use sigle metal core it's make resonance use multi core
So you're making a first order low pass filter. If you lay your speaker face down on a table it sounds better with that low pass.
The crucial part to good sound, perfect crossover network design, takes some effort in measurement and simulation. A first order low pass for example only works in 1% of all cases. The responses of the drivers have to overlap for several octaves for it to work.
I recently made a tutorial for 2-way crossover network design. Please have a look, there's more to come: ruclips.net/video/5Kvl0iBQ0L0/видео.html
Ok, I need some info and help. Can I run a 3000w amp on a 170 amp alternator?
Yes u can
That is a toroidal transformer and basicaly eliminates high frecuency noises and helps to keep a low frequency for base, those are common in passive and active cross over
Since the quality of the screws is different, the HenRy values may change
Passiv crossover filter pass bass 6db octave .
All youre doing is making a choke coil... It just inhibits high frequencies
All you did is make an oversized resistor... That will only do the opposite of what title says... If you want more power, should think about moving to lowering the resistence by using smaller wire. Example: instead of 14guage use 18guage
its only 85 tunes..how about more 100 tunes it is different
I'm just here to cringe as an electrical engineer.
And.....
How to increase bass .............remove all the high frequency.
The speaker cone isnt reacting at all when you touch the coil to it. Looks dubbed over to me
So let's see another video in the channel to know right away
Il faut une bobine qui fait plus de 5 mH et sur le HP, en parallèle un condensateur de forte capacité....beaucoup plus efficace ainsi.
Bass 3 tấc cuốn bao nhiu vòng vậy anh
You dont have a heat gun !
what is the coil swg number ????????
be plumb and level with me, is this by the square???
Square or circular shapes can be used
Seems legit
I am very interested in musical Tesla coil, sir, would you ever considered a project like that??
Yes, I will do it
thx for the quick reply... :) as always i will wait for ur new videos :)
Inilah cara menghilangkan frequensi bass..... Hahaha
What is the song name???
from this video no avail. this video is just for taking the time out of vain. even to gain views. Nothing more
It does not work I try it and did not work:(
You have to try it correctly, which means you should try it for a long time
@@AlfredH I will try it that way move it doesn't work it doesn't work
How speaker capacity increase by adding extenal wiring?
I do not quite get it
Induction current gain
Good....Thanks for sharing your knowledge
Thank you very much
all effort waisted to intentionally allow mid frquencies to pass thru...tutorial should be titled..."winding bit of wire lets see what happends"..
You built a crude PASSIVE single pole low-pass filter. This is not new technology and is done poorly here. It does not increase loudness. The core is not good because of eddy current losses and possible saturation/hysteresis distortion at higher currents. Fun if this is your first time experimenting though (in case anyone wants to ride me about being negative lol)
This core I apply for low frequencies, not high frequencies that are afraid of saturation.
Manufacturers filter for low frequency they still use the iron core of the transformer. This core is even lower than the transformer core so it is not afraid of saturation
Yes the core passes the most current at low frequencies, which will create the most magnetism and risk of saturation. Maybe it won't happen if your power is not too high. But a transformer is designed within it's limits and does not affect your results. If you want a core, best use a laminated or ferrite core. You'll lose some power inside this core. Professional literature about passive crossover circuits will tell you similarly. Goodluck :)
you did not increase anything, you only created a passive low pass filter
Тоже ищешь русский комментарий?
да
Archi Walking ага
Это он типо фильтра высоких частот сделал ?
Самый лучший комент😊😊😊
@Александр МатонинСМЫСЛ ЭТОЙ КАТУШКИ?
Tutte stupidaggine di scrivere le potenze che dichiari. Non hai le capacita' per farlo. Hai creato una classica bobina induttanza che filtra il basso del woofer allegato , per rendere la gamma taglio frequenza medio-alta-bassa
what are the materials do i need to make like that?
You need a copper wire with insulating paint. and an iron screw exactly the size of the video
good men
How to make speaker louder: build a proper enclosure
you can list the materials you want to use in the video
yes
@@AlfredH please list the name of the material
nice
Thank you very much
Its that true?
This is way to funny
It did nothing but increase the length of one wire, what a joke!!
But when I should that better ya screw nut please say that
На мерседесе давно такие обмотки стоят
Sir wat is d name of side plate plz reply plz 🙏🙏🙏
I do not understand
For what extra you get out of it is not worth the trouble
Song name?
Crossover not bass boosted, and definitely not 3000k watts.
Eliminating high frequencies means increased bass.
3000w depends on copper wire size
شكرا
I don't think that improves the sound.
It sounds tinny and scratchy. But hey that could just be from recording sound from the backwave of the driver.
why? Why do they have to produce Audio Frequency Divider? Frequency regulators can regulate and shrink, which will balance the speaker output with the amplifier. along with other speakers. If you connect directly to the amplifier. The loudspeaker may be shaken if the amplifier is weak, and the loudspeaker may be choked if the amplifier is too strong. Even broken speakers, if the speakers are not enough capacity to resist.
When you add a frequency divider, the sound will be more rounded
The coil has a high frequency stop function
The frequency range of the audio is from 22hz to 20Kh
The lower the frequency, the stronger the bass.
Would you choose the frequency for the bass speakers or would it be better?
If this bs actually gave it 3000watts everyone would be doing it🥱
Voce e o cara
i dont need this, i have lanzar max 12 1000w, 12 inch, good bass
So what is this coil exactly?
A basic low pass filter, which attenuates high frequency signal and pass low frequency portion of the music.
thank sathish sukumaran you have answered
Anyone see the freemason symbol at the top left
I do not understand
El final del video es malisimo! Se escucha igual de mal en ambos casos!!
nothing happens
You know the reason I use black iron screws as the core
sounds the same on camara. 👐😩💨
ashutosh kumar
Porno
ashutosh kumar khmer
I tried this, it works. The bumpers fell off my car after I cranked my stereo with the doorbell coils attached to the speakers.