9:46 😭holy shit I cried in German bcz that’s true when you see a check engine light Ofcourse the blown bulb isn’t the first thing that comes to your mind
I’d bought a pro device from Russia for Vento (2018, 1.2 TSI HL+). How to get setup the vehicle with VIN? There is no option showing Vento instead of Polo and Rapid. I have selected the Polo but couldn’t activate any of the preloaded feature/apps like basics needle sweep etc. please help in this regards. Thanks.
Sir , there is no vento in international markets , its known by the name of polo sedan , there should be an option where OBDeleven will confirm the model year , model selection ( 5 or 3 door ) and engine option , select those according and it will work .
Hi can you open the thermostat on the waterpump with this ? Ive got the pro version tool , By the way my car is a 2016/17 polo 1.8 gti tsi bluemotion 192ps , DAJ engine . The car has mostly everything activated already from the manufacturers so theres not much i want to change tbh , ive turned on & turned off some features already tho which aint causing any problems so all is good on that side of things . Opening the thermostat will help greatly whilst flushing the system without actually heating engine up . I know i can activate the radiator by-pass valve with the obdeleven pro Aswell
Sir , just make sure that its held in position firmly , basic motive of mounting bracket is to keep it firmly in place , so if you have tied it down properly then no need of new bracket
Hi, sir.. I own VW polo 1.2 tdi M-2012. I am facing issue while shifting to reverse gear (grinding noise) this comes up after I drove the car for few kms. If standstill after ignition it shift s normally to reverse gear no noise. [ After driving few kms if I want to shift it to reverse without getting the grinding noise I need to shift it to 1st gear then to reverse, in this scenario there won't be grinding noise ] This problem started after replacing clutch set (OEM) at 65000 kms, but didn't go for transmission oil change (since mechanic said oil was looking good no need to go for changing showed by loosing the filler bolt) . After this I was experiencing the reverse gear grinding issue. So thought to change transmission oil got it replaced, (oil was some other brand - offered by go mechanic workshop). Even after this issue couldn't be resolved. I have hard shift s sometime s in 3 & 4 gears. A local mechanic said need to do clutch air out / clutch bleed. Slave cylinder and master cylinder are in good condition. There is no squeaking noise while released/pressed. So need your advice in this concern.. - Do I need to drain out transmission oil and change it with oil - sk zic 75w-85 ( as seen from one of your video) a right method. So that issue would be solved!! If not - How and when to do clutch bleed / air out ? After the changing to new oil! Help me out in this regard.... Thank you in advance.
Sir , Very first thing i need to know that is , did you changed the flywheel along the clutch or not ? The grinding noise usually comes when we don't press the clutch fully and try to change gears . Bleeding air out of clutch system is a good idea you should try it , because if there is still air trapped in clutch system then pressure plate of cluch will not recieve full pressure from the pedal . Changing the transmission oil after a clutch replacement is a must , as you have spend a good amount on clutch plate , pressure plate and bearing then its a wise idea to change the fluid and be worry-free till next time , if you want to swap transmission fluid then use motul , its better than sk zic ( i have a video on it as well ) Last possibility of grinding noise is syncros themself , they are located in between the 2 gears to make the gear shifting process smoother , if cogs of syncro are eaten up then they will grind , but in your case as you said that it happened after clutch work . Its almost impossible Did mechanic calibrated the gear shifter and shift lever after the clutch work ? Because in these vehicles after you remove transmission you need to re calibrate the shifter and lever to have perfect shifts . (Most probably this week i ll upload a video on this process as well ) Just in case you reply again , and get no reply then please send me a mail at everydaydiyhelp@gmail.com , after update of youtube app , sometimes it doesn't show any notification of the new comments. Hope it helps sir
Hi Sir, I need your suggestion, I am looking to tweek my brand new VW Taigun is it safe to get it done by professionals with vcds. Is it safe and will it void any warranty if it get it done.
Sir Very good morning, I don't know how i have not come across you superb channel till few days back. Very knowledgeable videos. thank you. I have a 2013 Vento highline TDI covered 1.55lac kms till today. Till now I have only changed the front suspension. I am still running completely stock on clutch and all other parts including timing belt and water pump. I am planning to change the clutch + timing belt & water pump + few other minor issues to sort out... 1. Regarding the clutch - no loss of power or pickup till now but it has become slightly heavy. However when in heavy / slow moving traffic there is slight jerky-ness while releasing the clutch slowly - is this because of the clutch ? While changing the clutch - Should i change the full clutch package including the pressure plate, friction disk and clutch bearing ? What will be the rough cost to change the clutch ? Shall i ask the mechanic to also do preventive cleaning of EGR valve and throttle body ? ... is there anything else i need to do preventive cleaning and maintenance for ? 2. There is a squeak noise when releasing the clutch pedal - i feel this noise is coming from somewhere near the clutch pedal possibly behind the firewall - what could be the reason pls ? 3. Last 2 days the center aircon vents on the dashboard - there is no air blowing - however air is coming at full blast from the side aircon vents. Also when i change the direction of air from dashboard to feet there is no air blowing. Could this be a the blower or resistor issue or the motor for air direction flaps behind center aircon vent ? ... Lastly is the VAG-COM VCDS -OR- OBD 11 better ? The Vento is a beautiful car sturdy and fantastic mileage (18-20 on highway with full load). With your help i hope to be able to maintain the car well and enjoy more years with it. Thank you very much for this channel and your service. Extremely grateful.
Sir if its truly an elm327 chip with the required protocols then yes it can do that , but a lot of those elm327 in market are fake , so just be a little careful
@@yourDIYneedsCan you give a demo as to how the SAS can be reset / calibrated using this tool ? It will help many that are looking for this as most of the VW / Skoda are out of calibration these days .
Hi brother...I wanted to ask that white smoke from the dipstick and oil filler cap in the Volkswagen Polo 1.5 tdi (2015) normal in vag cars or their is some issue? Also how much is the normal engine oil consumption in polo tdi as I got my polo serviced in April but today morning as I checked the engine oil is showing low level ...I am worried kindly advise
Sir blowby smoke is a normal thing in vw tdi engines , oil consumption acc. To VW USA says that any amount of consumption below ( 1 fl. quart / thousand miles ) is still considered to be normal consumption Nothing to worry about sir , its normal
@@yourDIYneeds ohh okay....(1fl.quart)?? And yesterday I went to a car garage to get liquimoly injector cleaner liquid to put in my fuel tank ....looking at the white smoke he said that the piston rings have been damaged and the oil is going in the combustion chamber and quoted a expense of around 80-90 thousand. Can you also tell the reasons behind piston ring damage and the problems/symtoms which the owners might face in this situation just to ensure everythings fine and for knowledge too!!
Volkswagen tdi has engine blowby by design , its not a problem , if the engine oil starts to burn inside the combustion chamber then you will experience light blueish smoke , white smoke means the mix is getting rich , and system needs cleaning , sir just use the injector cleaner and if possible get following things cleaned properly 1. MAF sensor 2 . intercooler 3. EGR system ( if not complete , atleast the return pipe) 4 intake manifold Your problem will go away . Hope it helps And sir yes 1 fluid quart
@@yourDIYneeds okay and how will all this cost any rough idea?..I have just come home from the garage ....brother their is no engine oil left it is at its lowest and guess what I got the car serviced on 15th April 2021 ....The mechanic said he would clean the intercooler let's see.Lastly thankyou so much for responding and I hope it helps.
im interested in video in motion coding for my skoda rapid 1.6 mpi. But OBD11 does not show me in the apps of my car. Any idea of long coding instructions? Also have you tried mirror dip function on reverse?
Sir video in motion depends upon the video playing capabilities of the headunit n, and mirror dip is not possible , as it requires a memory module , which rapid doesn't have
@@yourDIYneeds I got a Blaupunkt Key Largo 970 on which Prime video, hotstar, RUclips video plays while in motion. But direct video playback from USB does not work
Sir obd unlocking only works with the OEM headunit , as blaupunkt is an aftermarket unit , so it won't have any effects on the unit , main reason why unit is not playing video when on move is because it can sense that the car is moving by voltage , and regulations define that car headunits are not allowed to play videos while on move .
Sir that totally depends upon the BCM your car has , but as far as my knowledge goes , yes that BCM support needle sweep but only the version 1 not version 2
Hey! Great video. I have a Jetta 2016. I wanted to buy this to activate AppConnect but not sure how it's delivered in the pandemic. Could you please share some info, how much you paid, how many days it took to be delivered, did you have to pay any customs?(I am more sceptical about this because I don't know how the customs procedure works) Lastly, if you stay around Pune, I could visit near your place and we could enable things at your place itself😎
Sir i would love to do it , but i reside in delhi 😅 I paid €43 for the device and then around ,€40 or so for the pro pack , it got delivered in 9 days from europe . I paid no customs , maybe thats because i have good relations with the local postman , as this is going to take the path of govt indian post , so maintaing a good relation with postman is very essential 😅 , i have good relations because i used to order alot of things from china and after so many packages he saved my contact and everytime he just calls me to inform that one of my packages have arrived .
@@yourDIYneeds Thank you for the information. Will place the order then. And no need to call us "Sir", everyone is learning from you. Instead, we should be calling you Sir. Thank you!
I got this device today but i cant enable settings that you have shown in long coding it is asking for a pro or the ultimate plan should be activated i purchased it for 3800rs and customs 1723rs and brake bleeding also not working asking for subscription
I'm using obd11 for about a month now (scanning+apps) and have bought credits to do some minor mods. Went to work and came home and tried to do some other app modification but suddenly most of the apps are 'not supported' (red error when clicking on the app) so I can't change anything. Even the apps I already changed are 'not supported' and it can't be that my cars is not supported to change.Tried reconnecting and rebooting the phone but no solution yet. Any suggestions?
2015 polo . On my mutifunction dispaly language change to german . How can I fix back to english. I am using after market android radio 10.1. Please help to get it back
Hello sir please help me. In my vw polo 1.2 petrol 2011 model when i turn ignition key on all dashboard sign showed and disappear after few seconds but only EPC and Engine sign still showed. But when i start the engine this two sign also disappear. Can you help me sir what is the issue? Thank you.
No sir , basic scanning is always free , but if you want to install new apps and activate features which are not already activated then you need to use credits . You can buy credits but you can also earn credits by watching ads .
Sir , Warrenty totally depends upon the service centre , they just need a tiny clue that someone's has touched the vehicle from outside and they will void the Warrent , even if a changed screw will make them feel that someone tried to open a certain part .
HI, can you please also make a video on how to activate "App connect "and "Voice" funtion in vw models after 2016 if they are not activated ? to get them directly opened from vw cost you good amount of money. Thanks
Sir thats possible , as soon as you will plug obdeleven then you can enable it with help of long coding , or prebuilt apps , here we don't have touran , so i never connected the device to touran , but if vw is charging a price to do it , then its definately possible with obdeleven
@@yourDIYneeds thanks for the quick reply, really appreciate that. Last thing dear If you can just please share the link for OBDEleven and if ypu know long coding for that. Thanks
hai, does it support fuel injector coding ? Bcz recently I changed my fuel injector with other one and the mechanics didn't do coding for that injector, thereby I am facing lots of power loss. So could you help me.
Sir you can watch ads if you don't want to buy credits , like you can watch 5 ads everyday fir credits + they will give you 1 credit if you open the app everyday
Sir codes to MAF/MAP sensor se related hai dono , agar MAF hai to clean ho jaega , lekin MAP to clean bhi nahi jo sakta . Ek bar aap pehle wire check kar lo
Thankyou and Love from Pune 💙💙💙💙
Great device for the basic user that wants to tinker.
For everybody else there VCDS and ODIS to do some real coding and maintenance
Very useful information you shared about this device great 👌👍👍👍
9:46 😭holy shit I cried in German bcz that’s true when you see a check engine light Ofcourse the blown bulb isn’t the first thing that comes to your mind
Hi bro i just wanna ask does it work on 2012polo/vento?
Yes it does , but features depend on the compatibility of BCM
I’d bought a pro device from Russia for Vento (2018, 1.2 TSI HL+). How to get setup the vehicle with VIN? There is no option showing Vento instead of Polo and Rapid. I have selected the Polo but couldn’t activate any of the preloaded feature/apps like basics needle sweep etc. please help in this regards. Thanks.
Sir , there is no vento in international markets , its known by the name of polo sedan , there should be an option where OBDeleven will confirm the model year , model selection ( 5 or 3 door ) and engine option , select those according and it will work .
@@yourDIYneeds Thanks for your very quick reply.
I’d already selected 5 door Polo but couldn’t get the features activated.
Sir if you want i can provide you my vin no to try . But on mail 😅
Hi can you open the thermostat on the waterpump with this ? Ive got the pro version tool ,
By the way my car is a 2016/17 polo 1.8 gti tsi bluemotion 192ps , DAJ engine .
The car has mostly everything activated already from the manufacturers so theres not much i want to change tbh , ive turned on & turned off some features already tho which aint causing any problems so all is good on that side of things .
Opening the thermostat will help greatly whilst flushing the system without actually heating engine up . I know i can activate the radiator by-pass valve with the obdeleven pro Aswell
Great stuff
Did you manage to enable the ComingHome/LeavingHome function?
No sir , i think they only work with automatic headlight option.
Control module (behind air filter) clips broken, have tied it with wires. It held up well till now , is it necessary to install new clips
Sir , just make sure that its held in position firmly , basic motive of mounting bracket is to keep it firmly in place , so if you have tied it down properly then no need of new bracket
@@yourDIYneeds thanks , are earlier vento(2013) suspension stiffer than present cars
Yes sir , a little bit
@@yourDIYneeds thanks will try to get them
Hi, sir.. I own VW polo 1.2 tdi M-2012. I am facing issue while shifting to reverse gear (grinding noise) this comes up after I drove the car for few kms. If standstill after ignition it shift s normally to reverse gear no noise. [ After driving few kms if I want to shift it to reverse without getting the grinding noise I need to shift it to 1st gear then to reverse, in this scenario there won't be grinding noise ]
This problem started after replacing clutch set (OEM) at 65000 kms, but didn't go for transmission oil change (since mechanic said oil was looking good no need to go for changing showed by loosing the filler bolt) . After this I was experiencing the reverse gear grinding issue. So thought to change transmission oil got it replaced, (oil was some other brand - offered by go mechanic workshop). Even after this issue couldn't be resolved. I have hard shift s sometime s in 3 & 4 gears.
A local mechanic said need to do clutch air out / clutch bleed.
Slave cylinder and master cylinder are in good condition. There is no squeaking noise while released/pressed.
So need your advice in this concern..
- Do I need to drain out transmission oil and change it with oil - sk zic 75w-85 ( as seen from one of your video) a right method. So that issue would be solved!!
If not
- How and when to do clutch bleed / air out ?
After the changing to new oil!
Help me out in this regard....
Thank you in advance.
Sir ,
Very first thing i need to know that is , did you changed the flywheel along the clutch or not ?
The grinding noise usually comes when we don't press the clutch fully and try to change gears .
Bleeding air out of clutch system is a good idea you should try it , because if there is still air trapped in clutch system then pressure plate of cluch will not recieve full pressure from the pedal .
Changing the transmission oil after a clutch replacement is a must , as you have spend a good amount on clutch plate , pressure plate and bearing then its a wise idea to change the fluid and be worry-free till next time , if you want to swap transmission fluid then use motul , its better than sk zic ( i have a video on it as well )
Last possibility of grinding noise is syncros themself , they are located in between the 2 gears to make the gear shifting process smoother , if cogs of syncro are eaten up then they will grind , but in your case as you said that it happened after clutch work . Its almost impossible
Did mechanic calibrated the gear shifter and shift lever after the clutch work ?
Because in these vehicles after you remove transmission you need to re calibrate the shifter and lever to have perfect shifts .
(Most probably this week i ll upload a video on this process as well )
Just in case you reply again , and get no reply then please send me a mail at everydaydiyhelp@gmail.com , after update of youtube app , sometimes it doesn't show any notification of the new comments.
Hope it helps sir
Hi Sir,
I need your suggestion, I am looking to tweek my brand new VW Taigun is it safe to get it done by professionals with vcds.
Is it safe and will it void any warranty if it get it done.
Sir Very good morning,
I don't know how i have not come across you superb channel till few days back. Very knowledgeable videos. thank you.
I have a 2013 Vento highline TDI covered 1.55lac kms till today.
Till now I have only changed the front suspension. I am still running completely stock on clutch and all other parts including timing belt and water pump.
I am planning to change the clutch + timing belt & water pump + few other minor issues to sort out...
1. Regarding the clutch - no loss of power or pickup till now but it has become slightly heavy.
However when in heavy / slow moving traffic there is slight jerky-ness while releasing the clutch slowly - is this because of the clutch ?
While changing the clutch - Should i change the full clutch package including the pressure plate, friction disk and clutch bearing ? What will be the rough cost to change the clutch ?
Shall i ask the mechanic to also do preventive cleaning of EGR valve and throttle body ? ... is there anything else i need to do preventive cleaning and maintenance for ?
2. There is a squeak noise when releasing the clutch pedal - i feel this noise is coming from somewhere near the clutch pedal possibly behind the firewall - what could be the reason pls ?
3. Last 2 days the center aircon vents on the dashboard - there is no air blowing - however air is coming at full blast from the side aircon vents. Also when i change the direction of air from dashboard to feet there is no air blowing. Could this be a the blower or resistor issue or the motor for air direction flaps behind center aircon vent ? ...
Lastly is the VAG-COM VCDS -OR- OBD 11 better ?
The Vento is a beautiful car sturdy and fantastic mileage (18-20 on highway with full load). With your help i hope to be able to maintain the car well and enjoy more years with it.
Thank you very much for this channel and your service.
Extremely grateful.
Sir now got your comment and replied on mail .
@@yourDIYneeds Thank you for your time and service Sir. I have received and replied to your email. Thank you ...
bro can we get live data from speed sensors using obd eleven? can we know abs fault codes as well?
Yes sir but live data is only available in pro version or above , not in basic
1st view 1st like and Watching ........
Can you send the link from where to buy
Hey bro really loved your video.. Bro can you help me in enabling these features on my VW Polo.. I live in Delhi
Sure sir why not
When and where can we meet?
Sir mail me at everydaydiyhelp@gmail.com , we will discuss it there .
@@yourDIYneeds thanks alot
Does it support with skoda fabia
Hi sir I need to off the 80 and 120 speed warning sound in vw ......is it possible using obd eleven ....... Can u suggest me the options
Yes sir , its possible
Version &price
Hi can I use the Android Torque ELM blue 327 2.1v OBD2 scanner to enable features like the mfsw on my 2016 Polo TDI Comfortline?
Sir if its truly an elm327 chip with the required protocols then yes it can do that , but a lot of those elm327 in market are fake , so just be a little careful
@@yourDIYneeds Thank you for the response and clarification.
Can hill hold assist can be activated from this device
Sir in a manual ?
In a automatic , yes but it depends on the support from BCM
@@yourDIYneeds sir in a manual
Sir as far as i know , in a manual its not possible , we don't have the hardware
@@yourDIYneeds thanx you sir
Hi. Can I calibrate the Steering Angle Sensor on my Vento TSI AT with this device ?
Sir yes , we can reset all the previously saved data in the steering module and then it will adapt again
@@yourDIYneedsCan you give a demo as to how the SAS can be reset / calibrated using this tool ? It will help many that are looking for this as most of the VW / Skoda are out of calibration these days .
Sure sir
Could we modify egr data by this device in Skoda rapid 2014
Sir we can modify the long coding , but modifying the duty cycle will not be possible
Hi, you always post videos which i am in need. :) can you share which plan/product did you buy, from where and how much it costed?
Sir i bought it from official site of obdeleven , device + pro pack it costed me £43 for device and close to £25 for pro pack
@@yourDIYneeds was it including shipping? How long did it take to deliver after ordering
It took 6 days , yes shipping included
@@yourDIYneeds Which postal service you have chosen ?
Standard india post , but you need to have good contact with your local postman 😅😅
Hi brother...I wanted to ask that white smoke from the dipstick and oil filler cap in the Volkswagen Polo 1.5 tdi (2015) normal in vag cars or their is some issue? Also how much is the normal engine oil consumption in polo tdi as I got my polo serviced in April but today morning as I checked the engine oil is showing low level ...I am worried kindly advise
Sir blowby smoke is a normal thing in vw tdi engines , oil consumption acc. To VW USA says that any amount of consumption below ( 1 fl. quart / thousand miles ) is still considered to be normal consumption
Nothing to worry about sir , its normal
@@yourDIYneeds ohh okay....(1fl.quart)?? And yesterday I went to a car garage to get liquimoly injector cleaner liquid to put in my fuel tank ....looking at the white smoke he said that the piston rings have been damaged and the oil is going in the combustion chamber and quoted a expense of around 80-90 thousand. Can you also tell the reasons behind piston ring damage and the problems/symtoms which the owners might face in this situation just to ensure everythings fine and for knowledge too!!
Volkswagen tdi has engine blowby by design , its not a problem , if the engine oil starts to burn inside the combustion chamber then you will experience light blueish smoke , white smoke means the mix is getting rich , and system needs cleaning , sir just use the injector cleaner and if possible get following things cleaned properly
1. MAF sensor
2 . intercooler
3. EGR system ( if not complete , atleast the return pipe)
4 intake manifold
Your problem will go away .
Hope it helps
And sir yes 1 fluid quart
@@yourDIYneeds okay and how will all this cost any rough idea?..I have just come home from the garage ....brother their is no engine oil left it is at its lowest and guess what I got the car serviced on 15th April 2021 ....The mechanic said he would clean the intercooler let's see.Lastly thankyou so much for responding and I hope it helps.
Sir its just labour cost , maybe a mechanic will charge 600-700 max for these things
Sir I have Polo Trendline 2021, can i match OEM Remote with obdeleven to my car?
Sir as far as i know , its not possible with obdeleven , you need special remote coding equipment for that
Do you know how to code multi function steering wheel??
Yes
Bro can you help me to remove 80/120 speed warning. Exactly where I need to code.
Sure sir
U great!!!!
Can we reset the dashboard warning lights using this OBD scanner
Sir not just reset , you can do almost everything , you can even code new injectors
@@yourDIYneeds w😲w ji
Can traction control be turned off in a non GTI polo?
Sir in most of polos yes its possible to turn of the traction completely off , but it also depends upon the BCM you have
hey bro pls share the buy link of obd eleven
Sir just visit their official site , or just google it
Version &price
Sir device is for around £43 + pro pack is for around £24
Indian rupees
Sir around 6 thousand in total
im interested in video in motion coding for my skoda rapid 1.6 mpi. But OBD11 does not show me in the apps of my car. Any idea of long coding instructions? Also have you tried mirror dip function on reverse?
Sir video in motion depends upon the video playing capabilities of the headunit n, and mirror dip is not possible , as it requires a memory module , which rapid doesn't have
@@yourDIYneeds I got a Blaupunkt Key Largo 970 on which Prime video, hotstar, RUclips video plays while in motion. But direct video playback from USB does not work
Sir obd unlocking only works with the OEM headunit , as blaupunkt is an aftermarket unit , so it won't have any effects on the unit , main reason why unit is not playing video when on move is because it can sense that the car is moving by voltage , and regulations define that car headunits are not allowed to play videos while on move .
Can CRUISE CONTROL activated in polo gt tdi 1.6 2014 model?
Yes sir , bcm has a support for cruise control , just have to wire the controls and activate the cruise control via VCDS
@@yourDIYneedscan we activate cruise control using obdeleven
Bro I just have a single doubt....in 2012 polo comfortline! Can we enable needle sweep with obdeleven?
Sir that totally depends upon the BCM your car has , but as far as my knowledge goes , yes that BCM support needle sweep but only the version 1 not version 2
@@yourDIYneeds thank you bro...I just wanted to know because 2012 Is bit too aged out ..and I thought ... whether I have to upgrade the BCM itself
No sir no need of upgrading BCM , it will work 👍
@@yourDIYneeds thank you for your reply bro ...
Anytime sir 🙂
Hey! Great video.
I have a Jetta 2016. I wanted to buy this to activate AppConnect but not sure how it's delivered in the pandemic.
Could you please share some info, how much you paid, how many days it took to be delivered, did you have to pay any customs?(I am more sceptical about this because I don't know how the customs procedure works)
Lastly, if you stay around Pune, I could visit near your place and we could enable things at your place itself😎
Sir i would love to do it , but i reside in delhi 😅
I paid €43 for the device and then around ,€40 or so for the pro pack , it got delivered in 9 days from europe .
I paid no customs , maybe thats because i have good relations with the local postman , as this is going to take the path of govt indian post , so maintaing a good relation with postman is very essential 😅 , i have good relations because i used to order alot of things from china and after so many packages he saved my contact and everytime he just calls me to inform that one of my packages have arrived .
@@yourDIYneeds Thank you for the information. Will place the order then. And no need to call us "Sir", everyone is learning from you. Instead, we should be calling you Sir. Thank you!
Which sites you used to buy … pls suggest me some
Sir i bought it from the official website
Cruise control install in polo mpi 2021 install or not
It can be done
I got this device today but i cant enable settings that you have shown in long coding it is asking for a pro or the ultimate plan should be activated i purchased it for 3800rs and customs 1723rs and brake bleeding also not working asking for subscription
Sir yes , for long coading you have to buy a pro plan online
I'm using obd11 for about a month now (scanning+apps) and have bought credits to do some minor mods. Went to work and came home and tried to do some other app modification but suddenly most of the apps are 'not supported' (red error when clicking on the app) so I can't change anything. Even the apps I already changed are 'not supported' and it can't be that my cars is not supported to change.Tried reconnecting and rebooting the phone but no solution yet. Any suggestions?
Modification you done are still working or they stopped working ?
2015 polo . On my mutifunction dispaly language change to german . How can I fix back to english. I am using after market android radio 10.1. Please help to get it back
Sir have to change it via vcds or OBDeleven
@@yourDIYneeds thanks. from service center can I change it
Yes sir
Hello sir please help me.
In my vw polo 1.2 petrol 2011 model when i turn ignition key on all dashboard sign showed and disappear after few seconds but only EPC and Engine sign still showed. But when i start the engine this two sign also disappear. Can you help me sir what is the issue?
Thank you.
Sir it seems to be normal
@@yourDIYneeds ok thank you 🙏🏻 have a great day.
Waiting for your new video😎
Does it compatible with 2012 vento 1.6
Yes its compatible with every Volkswagen after 1996
Hi bro do i need to pay money to scan error codes every time like scanning the abs module do i need to buy credits every time i am using this scanner
No sir , basic scanning is always free , but if you want to install new apps and activate features which are not already activated then you need to use credits . You can buy credits but you can also earn credits by watching ads .
@@yourDIYneeds ok bro thank you
Using these things hinder the warranty of the vehicle?
Sir , Warrenty totally depends upon the service centre , they just need a tiny clue that someone's has touched the vehicle from outside and they will void the Warrent , even if a changed screw will make them feel that someone tried to open a certain part .
@@yourDIYneeds Completely right..-thank you for your video on self servicing-really helpful..
HI, can you please also make a video on how to activate "App connect "and "Voice" funtion in vw models after 2016 if they are not activated ? to get them directly opened from vw cost you good amount of money. Thanks
Sir which vehicle do you have ?
@@yourDIYneeds vw touran 2017
Its just these 2 functions that I can't use, and it says contact dealer for activation.
Sir thats possible , as soon as you will plug obdeleven then you can enable it with help of long coding , or prebuilt apps , here we don't have touran , so i never connected the device to touran , but if vw is charging a price to do it , then its definately possible with obdeleven
@@yourDIYneeds thanks for the quick reply, really appreciate that. Last thing dear If you can just please share the link for OBDEleven and if ypu know long coding for that. Thanks
hai, does it support fuel injector coding ? Bcz recently I changed my fuel injector with other one and the mechanics didn't do coding for that injector, thereby I am facing lots of power loss. So could you help me.
Yes sir , it also supports new injector coding
@@yourDIYneeds Respected..Thank you Sir… You deserve all the polo owners appreciation….
Helo bro can u help me out to do coding fr abs module on polo
Is it coding or pairing ?
Like have you changed the module ?
I hav change d module
Its nt coded need to code it
@@yourDIYneeds
Changed d module
Need to code it
Sir in which city you reside ? If you are in delhi then i know a person who has ODIS , who can pair the module .
Goa
Bro i have unused credits.... How do i return them?
Sir i don't think its possible 😅
Hi bro it comes with lifetime subscription or need to buy every year?
Sir its yearly
@@yourDIYneeds Ok 👍 How much they charge yearly?
Sir, its around £20
@@yourDIYneeds thank u brother 🥰 and one more doubt i have what are those credit codes they are selling 100 credits code for €12.99?
Sir you can watch ads if you don't want to buy credits , like you can watch 5 ads everyday fir credits + they will give you 1 credit if you open the app everyday
Do you live in delhi?
Yes sir
I did a diy project of fitting a mfsw steering wheel in comfortline and was not able to get hold of a vcds can you help me out
Yes sure sir , why not
Can you share your insta id
Sir mail me at everydaydiyhelp@gmail.com
I ll share the details on mail
Sir meri polo petrol 1200cc mpi m P0068 and P0441 error code aa rha h kese resolve kru .
Sir codes to MAF/MAP sensor se related hai dono , agar MAF hai to clean ho jaega , lekin MAP to clean bhi nahi jo sakta . Ek bar aap pehle wire check kar lo
@@yourDIYneeds ok sir , thankyou
How to unlock few features for Skoda Rapid 2018 model automatic … ? Do you provide service and what cost ?
Sir i reside in delhi , if you live around i can do it for you
Can we enable mileage per litre in rapid ambition?
Yes sir
you had to tap on Byte 18
Sir if you know , can you share the discription of bits , if possible
@@yourDIYneeds tap on it and you wil see it, you said there is nothing thats why my reaction
Sir it says light setup , and has function to check out for blown bulbs
Where to buy obd eleven in india
Sir you have to buy it online from official site and they will ship it to you from europe
R2D2