Congratulations and THANKS!!! Was looking to install a precision motor & controller for a low-cost rotary assembly m/c, BUT.... this is such a clever solution! I'm changing the design and going for pneumatics 🤙!!
rotate table is good idea, but i see that when the clinder back up (off), it will touch in rotate table make small movation, and may be tolerance of rotate table in the production
😀I was looking for such of a machine. Is there a parts list for this device? I know that some parts are from 8020. How long is it? How wide ? And how far off the table does it sits? Great Machine.
Несколько приводных ремней, несколько шестерней для синхронизации, и весь пневмо механизм с электроникой можно заменить одним двигателем, похоже я не понимаю предназначение этого устройства.
I love it, air cylinders are easy to adapt.The magic is in the air logic.I wish I knew air logic. I'm down with the mechanics. How do you load the rotary table? Bowl Feeder?
@@stevematson4808 I have minimal knowledge about what you spoke. would love to know where do I start with learning this pneumatics and other mechanisms
Hye n hello.. I'm a Mechatronic student.. I really love your project.. An would like to remake it again as my project but will make some upgrades like using iot dan other.. Can help me.. With some clues or maybe a scratch or cadd or anything..
Congratulations and THANKS!!! Was looking to install a precision motor & controller for a low-cost rotary assembly m/c, BUT.... this is such a clever solution! I'm changing the design and going for pneumatics 🤙!!
rotate table is good idea, but i see that when the clinder back up (off), it will touch in rotate table make small movation, and may be tolerance of rotate table in the production
it's locking the table!
Here we should find a way to stop the rounded plate after turning it immediately before the piston returns back
Simple but great !
I love it !
This is so amazing.
😀I was looking for such of a machine. Is there a parts list for this device? I know that some parts are from 8020. How long is it? How wide ? And how far off the table does it sits?
Great Machine.
please, can i know all parts using in this system
very nice work!
Which plc is used in this project
Superb 👍🏻👍🏻
did you buy or build the gripper
Несколько приводных ремней, несколько шестерней для синхронизации, и весь пневмо механизм с электроникой можно заменить одним двигателем, похоже я не понимаю предназначение этого устройства.
I love it, air cylinders are easy to adapt.The magic is in the air logic.I wish I knew air logic.
I'm down with the mechanics. How do you load the rotary table? Bowl Feeder?
I think clippard pneumatics have alot of stuff that can be used for pure air driven automation.
@@stevematson4808 I have minimal knowledge about what you spoke. would love to know where do I start with learning this pneumatics and other mechanisms
@@rithiklodha4137 if you happen to be a factory mechanic you'll see a lot of pneumatics.
@@rithiklodha4137 i looked On Amazon. Pneumatic circuit building: Sivaraman, Dr. Ilango: 9781520862545: Amazon.com: Books.
@@rithiklodha4137 the Clippard website has a great how to section. www.clippard.com/cms/categories/pneumatics-101
please, can i know all parts using in this system?
You copied this from Ahmed ADEL
This is dope
Hanzhen harmonic drive gear ,
over 30 years experience ,
robot joint ,
strain wave reducer ,
jesus this guy is everwhere.
Compressor?
i m looking for the same for bottle washing machine to load table with high speed
that was super cool. which programming language ? or is it an electronic timing system ?
arduino maybe
PLC, its on the title
Hye n hello.. I'm a Mechatronic student.. I really love your project.. An would like to remake it again as my project but will make some upgrades like using iot dan other.. Can help me.. With some clues or maybe a scratch or cadd or anything..
I've same idea about mechanical pneumatics rotary. that's could be used for any complex and fully rotation. great idea. :)
hi
how can make pneumatic indixing rotary
pls tell me if you did it
@@AnwarAlfaqeehAlhusseini Read a book.
@@Nickael7 please send me that book as soon as possible. Thank you.
@@QwertyCanada Yeah, it's called "Read A Book". It's an amazing book that you can get at the corner of F and U. You can't miss it !
Do you need my email sir, please send thanks. Regards.
hello Sir, can you provide the schematic diagram?
what are the component you use to control the air
yes it is
So what's the problem??
Money, 80/20, so forth.
Simple device.. i'm plc engineer
Hai
He controlled manually by pushing the push button.
There is no PLC.
😂 get a clue mate