Thank you for responding. The crank went bad dirt was on the outside of the carb so I guess dirt got in the engine and wiped out the crank. I bought a 26cc engine and that works good and I bought outer wear cover for the filter hope that works. The engine is a hy are they good seems to have alot of power. Thank you
@punch800a4: It works good but they have had a problem with the one way bearing in the 1st series (the one you get from TGN). With respect to the Thread Lock...you need to put the non removable on the screw. You can still remove it with heat. Thread Lock becomes non functional above 150 degrees C. Hope this helps.
The screw kept coming lose was that the problem because that's the problem I'm having with mine. Mine is from kingmotor but I like the way yours looks. I put the blue lock tight on mine if it comes loose again I will use the red lock tight and yes it was a big help thank you let me know if that was the problem if the screw kept coming lose thank you.
I used the blue but it didn't work but now I think it the one way bearing, I drove it for like 5 minutes and it went their going to send me a new one way bearing and if that don't work then I don't know I guess I'll give it back to them. Ever since I got the 2 speed all I did was work on it, it sucks I want to start running it I want to see how fast it is. Someone is selling a cy 26cc with crank work done and a couple other things I'm thinking about getting it what do you think about that?
@jacobbryan17: This highly depends on the engine you are running. If you are running stock I would no go to high (relation small between gears). If you are running a tuned engine (high power) you can widen the gap from 1st to sencd gear. However, be aware that there has been an issue with the one way bearings on the 2 speeds. There are also other providers of 2 speeds that don't have that issue - check this up on ebay as well.
@Megabyteme325: Thanks for the comment. I saw the screw but either the metal was already little twisted or the hole was tight for the pin. I loosened the screw but the pin fell not out. Thats why the hammeraction followed...
How do you like that 2 speed. I put one on my mine it is a kingmotor 2 peed and the screw that holds the gear on keeps coming loose I just put lock tight on it but if it comes loose again I'm getting another one. I seen those on RUclips and they look easy to adjust the the 2speed thanks
@TheShaddy123456: You're 100% right. I would say the material if top quality but the failed with the supplier of the bearings. Btw: You can just replace the bearing against a VFX one and it works perfect. There are a lot of Treads in the forums that discuss the different suppliers. Also TGN is replacing the bearing if you tell them to. However, I highly doubt the process of testing before releasing the product to the market. The bearing would have failed in the first hour of testing...
@TheShaddy123456: The BRCP works perfect with no problems. Also the supplier sent me additional screws from the UK over to Switzerland with no cost. Its a top notch 2 speed with a top seller :-)
just t rying to understand a little how this works.... IS there two primary gears ? i know there is a clutch mechanism on secondary gear to activate second but can only see one primary gear driving both first and second. Something has to disengage first gear from primary gear when it hits second otherwise it will lock up correct? Please explain.. thnks
@TheShaddy123456: No problems at all so far. In use since approx 1 year. I cannot remember the name of the company that manufactures the one way bearing but you can just look up the internet with a seach after: TGN 2 speed problems and you'll find a lot of threads with manufacturers for the bearing...
What's up first I got the 2 speed working good but now the engine breaks up at mid to high rpm and it's sluggish I tried tunning it that did nothing can you help me thanks man name is Kenny by the way
Am I wrong but it seems like these 2WD buggies are quite nervous? The power is very direct (causing a lot of slippage) adding a 2speed would make this thing fly "like a bat out of hell". Are 4WD better? Looking to get into this scale from 1/8 buggies, 1/10 on road nitro.
@punch800a4: The engine has no valves in that sense. It all workes with holes and timing for air/gasoline intake and outtake :-). With respect to missing power in mid and high rev... What kidn of engine are you running and what kind of gearing. You might be overgeared and the motor has not enough power...
@punch800a4: Kenny, PM me with the explanation of what you mean with "the engine breaks up". Do you mean that the engine goes in some kind of free run? If yes, the one way is defect.
@punch800a4: If you want to get a 2 speed that works excellent take this: cgi.ebay.ch/BRCP-2-SPEED-GEARBOX-FOR-HPI-BAJA-AND-CLONES-KM-ECT-/160628528256?pt=UK_ToysGames_RadioControlled_JN&hash=item256634d480
Nice video, easy to understand. I'm waiting for my 2 speed to arrive. Thanks for the help!
Other than that it's good and is yours still running
Thank you for responding. The crank went bad dirt was on the outside of the carb so I guess dirt got in the engine and wiped out the crank. I bought a 26cc engine and that works good and I bought outer wear cover for the filter hope that works. The engine is a hy are they good seems to have alot of power. Thank you
@punch800a4: It works good but they have had a problem with the one way bearing in the 1st series (the one you get from TGN). With respect to the Thread Lock...you need to put the non removable on the screw. You can still remove it with heat. Thread Lock becomes non functional above 150 degrees C. Hope this helps.
The screw kept coming lose was that the problem because that's the problem I'm having with mine. Mine is from kingmotor but I like the way yours looks. I put the blue lock tight on mine if it comes loose again I will use the red lock tight and yes it was a big help thank you let me know if that was the problem if the screw kept coming lose thank you.
@punch800a4: Cool. Glad that you found the error. You are always welcome!
I used the blue but it didn't work but now I think it the one way bearing, I drove it for like 5 minutes and it went their going to send me a new one way bearing and if that don't work then I don't know I guess I'll give it back to them. Ever since I got the 2 speed all I did was work on it, it sucks I want to start running it I want to see how fast it is. Someone is selling a cy 26cc with crank work done and a couple other things I'm thinking about getting it what do you think about that?
still got mine .running sweet/
@jacobbryan17: This highly depends on the engine you are running. If you are running stock I would no go to high (relation small between gears). If you are running a tuned engine (high power) you can widen the gap from 1st to sencd gear. However, be aware that there has been an issue with the one way bearings on the 2 speeds. There are also other providers of 2 speeds that don't have that issue - check this up on ebay as well.
@Megabyteme325: Thanks for the comment. I saw the screw but either the metal was already little twisted or the hole was tight for the pin. I loosened the screw but the pin fell not out. Thats why the hammeraction followed...
How do you like that 2 speed. I put one on my mine it is a kingmotor 2 peed and the screw that holds the gear on keeps coming loose I just put lock tight on it but if it comes loose again I'm getting another one. I seen those on RUclips and they look easy to adjust the the 2speed thanks
Hey champ. Great video, thank you. Would you know if the same system mounts on a baja dark night? every thing looks the same
@TheShaddy123456: You're 100% right. I would say the material if top quality but the failed with the supplier of the bearings. Btw: You can just replace the bearing against a VFX one and it works perfect. There are a lot of Treads in the forums that discuss the different suppliers. Also TGN is replacing the bearing if you tell them to. However, I highly doubt the process of testing before releasing the product to the market. The bearing would have failed in the first hour of testing...
@TheShaddy123456: The BRCP works perfect with no problems. Also the supplier sent me additional screws from the UK over to Switzerland with no cost. Its a top notch 2 speed with a top seller :-)
The song is Tony Faline Feel the funk
just t rying to understand a little how this works....
IS there two primary gears ?
i know there is a clutch mechanism on secondary gear to activate second but can only see one primary gear driving both first and second.
Something has to disengage first gear from primary gear when it hits second otherwise it will lock up correct?
Please explain..
thnks
@TheShaddy123456: No problems at all so far. In use since approx 1 year. I cannot remember the name of the company that manufactures the one way bearing but you can just look up the internet with a seach after: TGN 2 speed problems and you'll find a lot of threads with manufacturers for the bearing...
What's up first I got the 2 speed working good but now the engine breaks up at mid to high rpm and it's sluggish I tried tunning it that did nothing can you help me thanks man name is Kenny by the way
thanks..this 2 speed TGN is better than 2 speed OBR?thanks
@headsmess: No. Try to install the latest flash player. Works perfectly on my side...
Am I wrong but it seems like these 2WD buggies are quite nervous? The power is very direct (causing a lot of slippage) adding a 2speed would make this thing fly "like a bat out of hell".
Are 4WD better?
Looking to get into this scale from 1/8 buggies, 1/10 on road nitro.
Depends on what your requirements are. More skill needed to drive a 2WD than a 4 WD. But yes, you are maybe right with the bat out of hell :-)
Are these available anywhere?
hy, where did you buy this 2 speed?thanks
@8itfrix: Nice. Let me know about your experience as soon as you have built it in :-)
Thank. I know what happend the crank went bad I guess dirt or something got in the engine and wiped out the cranks. Thank you for responding
Feel the funk - tony faline & Huda Hudia
The bearing is ok but at mid to high rpm the engine misses bad can't get any speed out of it and it has loss of power
@TheShaddy123456: ...for the second Q. King Motor does also offer 2 speeds but also the covers. Just check up Ebay...
Tony Falline - Feel the funk. Just check below the vid...
Kinda sounds like it has a bad valve but I don't think these engines have valves I will post a video about it tomorrow
@punch800a4: I think you should even use the green Thread Lock. Let me know the result!
what is the song ?
@Ragelundas:Sorry. Dont know anymore. Have chosen it trough AudioSwap.
@TheShaddy123456: Yes, I had the same problems. I have replaced it with a Version from the UK. The ebay link is in the comments thread.
@punch800a4: The engine has no valves in that sense. It all workes with holes and timing for air/gasoline intake and outtake :-). With respect to missing power in mid and high rev... What kidn of engine are you running and what kind of gearing. You might be overgeared and the motor has not enough power...
Anyone know where I can get this 2 speed??
Hi mate, originally it was from TGN Distribution but nowadays you can find 2 speeds on ebay...
@punch800a4: Kenny, PM me with the explanation of what you mean with "the engine breaks up". Do you mean that the engine goes in some kind of free run? If yes, the one way is defect.
@punch800a4: Always welcome :-)
@TheShaddy123456: It was around 150 bucks I believe...
You can almost buy Baja upgrade parts in Dollar Tree nowadays.
7:17 guessing after all these yrs and no vid of it running it was a massive fail.
@loco thank you
@TheShaddy123456: Hi mate, no..never heard about them.
@41612patria: Thanks!
TGN Distributing
@headsmess mine works 2
@punch800a4: If you want to get a 2 speed that works excellent take this: cgi.ebay.ch/BRCP-2-SPEED-GEARBOX-FOR-HPI-BAJA-AND-CLONES-KM-ECT-/160628528256?pt=UK_ToysGames_RadioControlled_JN&hash=item256634d480
that shit came with a plastic gear?....WTF
i just cant understand you guys putting new parts on a muddy dirty rig that does not make sense to me clean the thing first what the fuck haha
great video crap music but thanx
what you dont like the funk baby haha