Only video on RUclips about this. Much appreciated it. I wouldn't mind making a updated video but too angry and frustrated about this install myself. Was Scion expecting us the remove the motor every time we decided to remove a bolt? lol
Many later (?) videos instruct folks to unscrew a motor mount. Some instruct removing the headlight and windshield water reservoir, and/or what he eventually did - removing the bolt across from the lower bolt. All this was much easier in the days before cars shrank and smog became a target of folks who like breathing air we can see through.
thank you for this video. I had started taking the bumper off(per the other video ☺) then thought theres gotta b a better way. Had trouble getting to the bottom bolt at first. Appreciate it
Great video, didn't have to remove bumper etc. (other video) exactly the way he does it in this video...that's how you do it. Had a little trouble removing my 19" wrench from tensioner after putting belt back on but eventually got it. Thanks for the video sososhit!
Ffffffuuuuuuuuck that belt. Thank you for this vid. A helpful tip I found was dont put the top bolt in until after the belt is in. It gives you just enough slack to put the belt on. Once on then insert and tighten the bolt. Anyway thanks again, you saved my ass.
Was it easy to replace the belt? I did mine a few weeks ago, since the belt was new, had some difficulty getting it onto the tension wheel. So what I had to do was take off the front, right tire, remove the fender shield and turn the crank pulley until the belt slipped back onto the tension pulley.
Yea for the belt having the ratchet in place makes it harder. I did what you did as far as removing tire and plastic cover. Ran the belt first, then placed rachet thru belt on to the tensioner n just pull down on it and slid the belt over the tensioner. Less stress n stretch on the belt.
Ok can someone tell me what can it be for my scion not to start. I’ve changed the coils thermostat , fuel pump, fuel injectors, camshaft sensor, air mass flow sensor, about to replace the starter relay. And put my battery to charge at auto zone. I have to use starter fluid for my car to start any suggestions?
sososhit unconventionalWAYS I have the fuel pressure regulator but don’t know where is located in the car for me to replace it and the piece I have I don’t see it by the bar of the fuel injectors so I need find it so I can replace it
sososhit unconventionalWAYS do you think it can be the alternator as well? I had to charge my battery because they said battery still good and I was about to buy a new one she said no because can also be your alternator that’s draining your battery
@@sosounconventionalways2179 too bad my kid got an earful before I shut you down-have some self-respect and respect for others... and yeah... I'm moving on begger
@@sosounconventionalways2179 the moron here is you there are people in this world that don't like or tolerate people who are making public videos they have to sit and curse in the videos just to make themselves look cool news flash. It's not cool if anything it shows a complete and total lack with education and simple communication if you don't like what other people have to say and keep your comments to yourself jackass.
![BLACK BAG - Official Trailer [HD] - Only in Theaters March 14](http://i.ytimg.com/vi/Du0Xp8WX_7I/mqdefault.jpg)
THANK YOU! You saved me soooo much time. The new belt I put on was VERY tight. My brother and I dropped 100 F-bombs while doing it - just like you.
Only video on RUclips about this. Much appreciated it. I wouldn't mind making a updated video but too angry and frustrated about this install myself. Was Scion expecting us the remove the motor every time we decided to remove a bolt? lol
Many later (?) videos instruct folks to unscrew a motor mount. Some instruct removing the headlight and windshield water reservoir, and/or what he eventually did - removing the bolt across from the lower bolt. All this was much easier in the days before cars shrank and smog became a target of folks who like breathing air we can see through.
Just replaced my alternator is my 2010 xb using this method. Took no time and was way easier than trying to disassemble the front end of the car
Haha 😂 same
Thank you. I saw that half wit who disassembled half his car and went, yeah, no. I'm glad I found this one.
Bro. I finished in like a half hour. There is NO NEED to take all that other crap off like in the other video. Thank you so much for this.
Appreciate you. Thank you!
thank you for this video. I had started taking the bumper off(per the other video ☺) then thought theres gotta b a better way. Had trouble getting to the bottom bolt at first. Appreciate it
Thanks.! I saw that video too..😂😂🤣🤣. waste of time and unnecessary work... why make things harder.
Thank you SO MUCH for the video, I couldnt figure out where the tensioner release was.
You saved me $hop fees
Great video, didn't have to remove bumper etc. (other video) exactly the way he does it in this video...that's how you do it. Had a little trouble removing my 19" wrench from tensioner after putting belt back on but eventually got it. Thanks for the video sososhit!
Thanks dude.! Yea you have to find that sweet spot. Glad it helped.
I will swap out my alternator tomorrow, thanks for the vid. I will comment if everything went good lol.
Ffffffuuuuuuuuck that belt. Thank you for this vid. A helpful tip I found was dont put the top bolt in until after the belt is in. It gives you just enough slack to put the belt on. Once on then insert and tighten the bolt. Anyway thanks again, you saved my ass.
Is there a easier way to get this the 19 mm I can't get my hand back there
Man straight to the point!!! Good job
Es el vídeo el que me ha servido gracias
Thank you for the awesome video. Yeah fuck removing the bumper and headlight.
Was it easy to replace the belt? I did mine a few weeks ago, since the belt was new, had some difficulty getting it onto the tension wheel. So what I had to do was take off the front, right tire, remove the fender shield and turn the crank pulley until the belt slipped back onto the tension pulley.
Yea for the belt having the ratchet in place makes it harder. I did what you did as far as removing tire and plastic cover. Ran the belt first, then placed rachet thru belt on to the tensioner n just pull down on it and slid the belt over the tensioner. Less stress n stretch on the belt.
Dude you are a beast hahaha thank you 🙏🏻
Ok can someone tell me what can it be for my scion not to start. I’ve changed the coils thermostat , fuel pump, fuel injectors, camshaft sensor, air mass flow sensor, about to replace the starter relay. And put my battery to charge at auto zone. I have to use starter fluid for my car to start any suggestions?
Have you verified that your fuel pressure regulator is working properly?
sososhit unconventionalWAYS I have the fuel pressure regulator but don’t know where is located in the car for me to replace it and the piece I have I don’t see it by the bar of the fuel injectors so I need find it so I can replace it
For that car, regulator is inside the fuel tank. It sits inside the pump. Google it you can see pics.
sososhit unconventionalWAYS basically I don’t need the regulator if I replaced the whole assembly of the fuel pump
sososhit unconventionalWAYS do you think it can be the alternator as well? I had to charge my battery because they said battery still good and I was about to buy a new one she said no because can also be your alternator that’s draining your battery
His was a different year
Thanks man!
To the point 👍
Yay
put year in title for a thumbs up
My alternator is dead 😞 just checking the video for see how replace
It was pretty easy. just don't let the balt fall n you should be fine. Good luck on your repair
Good sh*t. 👍
Lmao strong language ..is there any other?
Probably good info, but I stopped the video after a minute due to the excessive language.
Shoulda hung in there.. guess you'll be removing full bumper. Good luck with your repair.
Oh no he said the F word. What are you 5 years old? 😂
@@TurboTurdBurglar 😂
@@sosounconventionalways2179
Op
Its a fuckin shame aint it. People putting shit like this on the Internet. I mean whi the fuck do they think they are?! /s
Really you don't need to be saying all kinds of bad words does not make you cool
"Cool" what are we in High school. take the information you need and keep it moving.
@@sosounconventionalways2179 too bad my kid got an earful before I shut you down-have some self-respect and respect for others... and yeah... I'm moving on begger
@@VoItaje go put some earplugs in your ears. Your a moron.
Lol, offended by a sound. Wow that's sensitive. Great video
@@sosounconventionalways2179 the moron here is you there are people in this world that don't like or tolerate people who are making public videos they have to sit and curse in the videos just to make themselves look cool news flash. It's not cool if anything it shows a complete and total lack with education and simple communication if you don't like what other people have to say and keep your comments to yourself jackass.