How To: Repair a Hayward Navigator or Pool Vac Ultra Pool Cleaner

Pool Vac Parts Results - bit.ly/2RoN6O8
How To Service the Inside of a Hayward Navigator Suction Cleaner HTG - bit.ly/36n2puP
How To Replace a Pod on a Hayward Navigator or Pool Vac Ultra HTG - bit.ly/2GlGvNW
How To Replace the Navigator Pool Cleaner Gear Box Assembly HTG - bit.ly/2RoWHUV
If your automatic pool cleaner is not operating efficiently, it may be time to replace the parts that are designed to wear. If you see significant wear on your cleaners shoes, wings or flaps, replace these parts to improve performance, and to prevent damage to the more costly components.
To view this guide step by step on our website, visit:
bit.ly/2uws1bi

[@tweetiebird]

This was great, not sure it covered the gear parts and that's everything but it had a lot of good information and I kept their number.

[@Inyopools]

Hello Dee - We have another video where we discuss the gear box. ruclips.net/video/FAxYoQsj7PY/видео.html

[@bobjudkins3926]

Very informative. That helps on how to repair pool sweeper. Thank you very much.!!!

[@poolmotorrepairguyFL]

These are a good little cleaner

[@chilejimenez]

Hello, I just replaced the A frame using the A-Frame/Turbine Kit Universal AXV621DAT but using the existing Pods. There is enough play between the A frames and Pod connection (the threaded connection, circular in shape, but with two flat sides 180 degrees opposed to each other). This loose connection makes one end of the pod hit the pool vac body, preventing it from making full range of motion while under water against the floor. When not in contact with the floor, you can see the vac pods moving fine, but as soon as it is on the floor it does not travel. Comparing this assembly with another functional pool vac, you can clearly tell that the play between the pod and the a frame should not be there and it should be a strong assembly with no play.
The A frame part number included in the AXV621DAT is V601D, vs the old one I had installed in my pool vac, V601. Are these two different? I see that there are kits for concrete and another one for "Desert" (kits ending in CAT and DAT respectively). Are these kits different and could the A Frames have a better/worst fit on the A-Frame and Pod connection depending on whether you use the concrete vs the desert version?

[@floydcalderon1556]

Very informative. Thank you!

[@lupocci]

At 6:40, I think you got the direction of the arrow 180 degrees off, could you please confirm? Thank you

[@robinkelley8124]

great video

[@Inyopools]

Glad you enjoyed it

[@tylerngo4894]

why my Hayward vacuum doent reach to the other end of my pool? I just replace the flaps, shoes, wings and A frame..Can somebody help?

[@Inyopools]

Hello Tyler, have you tried resetting the hose by laying them in the sun for a few hours? This gets the curl out of the hose making it more likely to stretch to the further parts of the pool

[@tweetiebird]

@@Inyopools I have the same problem and it's not a hose, I just had lesile rebuild (maintenance it) and it barely moves. Suction OK, hose OK, it moves slowly no matter how much suction I increase it to. I see it picks up leaves and cleans the flloor but it takes a long time and it never goes far enough to the end of the pool.

[@darbmann]

@@tweetiebird I'd like to know too. Mine is moving slow and I just bought it a few months ago....

[@tweetiebird]

@@darbmann I had leslie check it my vac again and confirmed it is OK. I did buy a new hose from Amazon and it was suggested I hook up to the skimmer and see if the vac works OK from there, if so I have a blockage in my pool vac line I need to fix. I will do and that report back.