It's able to produce about 300 Watt. It depends on the wind. But it’s enough to charge normal car batteries and so you can consume a lot of energy in a short period. And it’s surely enough to start your computer for 2 hours a day, or to charge a mobile, or to have light for reading the newspapers and to have a look at your pretty wife.
We used an old alternator from a Simca 1000. We assume a useable power of min. 200W in winds about 15-20mph. Our idea has two goals. At first it is a drawing sample in a new AutoCAD 2011 training-video. These videos will be seen millions of times all over the world. This chance is us our second goal. We found that it’s very easy to build and the materials can be found on auto graveyards all over the world. We hope that lots of people will use this construction and build their own Gwindoline.
Welcome Friends, 100.000 views - I thank you all. Especially your interest in green energy is warming my soul and gives me hope for the future. A main brain in developing these turbines is my friend Richard Schultes. So if you have technical questions, please write to richardschultes@yahoo.com. Greetings from Vienna. --- Only the globalization of information has the power to save our planet ---
Awesome video. Because there are power cuts in Ukraine, perhaps you can print 1000 instruction sets and send it to some ukraine addresses for distribution? Thee don't have the interweb most places.
Brilliant idea. I would add a cap over the upper bearing to protect it from rain and rusting. A similar project of mine some thirty years back produced horrible noises after a short while.
I had thought of a vertical wind turbine similar to a biscuit fan, and wondered if it had been done by someone...great design with the barrel! There seem to be many advantages over the typical "pinwheel" design...the flickering of sunlight that bothers some people should be much less...also, it has to be safer for birds, and more durable...also, no need to face it into the wind, as it is always able to catch wind from any direction. Another idea I had has to do with the generator. I thought of a design where the distance of the fixed magnets from the rotor can be varied. In light winds, the magnets could be more distant from the rotor, allowing free rotation and the production of some electricity, however little. As the wind increases, the magnets, by means of a governor (either mechanical or electronic), could be brought closer to the rotor, producing more current, and acting as somewhat of a brake so that the turbine doesn't spin too fast. However, I don't do any of this, just think about it.
This will never work. . ..The power output would be so small that it would be a huge waste of money. A car alternator spins at a min of 1000 rpm and its power output becomes maxed out at a much higher rpm. 1000 rpm is approx 170 rpm per second. . What you have done, is taken a slow turning trashcan that may reach 20 rev per second at its very best in high winds, and stepped it DOWN about 10 to 1 to the alternator. This will turn the alternator slow. Not enough If you get more than15 or 20 watts out of this thing, I think you will be doing extremely good. What looks good on paper doesn't mean reality is there. Great design, but non-functional. You have here a nice spinning ornament that looks cool and fools the fools that want free energy
@@arifcrafts3961 First you need a generator/alternator rated at the voltage you are using. Second you need the alternator to be turning at least idle speed. .. 1000 rpm. Third. How fast does your vertical turbine turn? 10rps? That's very fast. Probably 5rps in a high wind. 3 rps is closer to reality. That is 180rpm. Forth. You need 1000rpm but have 180rpm. That calls for a 6:1 pully ratio. Fifth. What i said above is all based upon a system with no load at all. With a load, that rpm will be slowed down to maybe 2rps. Which slows down you genetator to about 700 rpm. Just because it is turning, doesnt mean it is charging batteries. It takes about 16 to 18. Volts to charge a 12v battery. There is a huge reason why sellers and makers do not post windspeed vs power output. Because it takes a huge amount of wind just to get adequate power from the turbine Further down in the messages, the writer corrects someone and says he got 10 to 13 watts of power, not 300. This correction sounds about right. 10 to 13 watts of power.
The biggest difficulty I think would be to build this perfectly balanced and symmetrical turbine to reduce the vibration that is common in this type of vertical axis turbine.
Very nice, thanks for posting. I think that these uni-directional wind turbines from re-purposed hardware are the way to go for the majority of us who don't have the funds for the fancy store-bought stuff.
Não deixe as aletas fixas! Coloque um eixo em cada uma para que elas se movimentem independentes, abrindo a favor do vento e fechando contra o vento Com isso vai diminuir o arrasto aerodinâmico aumentando a eficiência. Mas o projeto é show por ser simples e eficaz. Parabéns!
Saludos de Joacin Montoya inventor de ESCRITURA GLOBAL. Con una gran idea electronica donde todas las personas MUDAS ban a poder HABLAR y en muchos idiomas del mundo.
hello, sir would you please tell me the output from the Generator? if you have no problem, please send me the project description file. I will be very grateful to you. Thank you
Nice work, especially the proper CAD modeling and the use of 5 sails. I am a bit concerned that it will flutter in strong winds... If so you might want to add support to the sail ends. I am basing this on experience - my dad and I built something very similar when I was a kid, using 3 aluminium sails, and the bearing and main pully from a washing machine drum - Looks like you also used a washing machine drum pully?. We mounted it around 5m up on a steel pole anchored to the ground. I like Savonius turbines because they are simple and easy to make.
could be used on a boat for a paddle wheel on the sides and back. to generate electricity in a creek. weld sprockets form old bike and make one big chain drive.
The bearings and the shaft must suit each other. We used a 60mm-pipe from a building scaffold. The two “square flange mounted bearings” can be easily bought in different shops for mechanical parts. Search for a local dealer on google. When you finished the assembly you have to balance it. For this put the whole thing in a horizontal position and look where turning stops. On that side reduce weight until it stops without turning back. For further details contact me: info.at.computerstall.ch
Only one-quarter right. I'm a pragmatist, not ignorant. And I'm more on the libertarian side of the Republican Party. I don't believe the central planners should be wasting tax payer money on expensive and unreliable "alternative energy" projects that are largely owned by Obama bundlers/campaign donors and usually end in bankruptcy while said bundlers/donors walk away with golden parachutes. The USA is the Saudi Arabia of natural gas and shale oil/tar sands. That's where we should be focusing.
Okay. This tit-for-tat is getting ridiculous. We need to end it sometime soon and go on with our lives, but my grand children will be paying crushing taxes to pay for the boondoggles of present. You get the last word.
Great invention. It really is that simple, although... the materials are a little heavy. On a light breezy day you would miss out on generating power. So although wonderfully designed, not at optimum efficiency. God bless
Nếu bạn muốn tăng hiệu suất của cái cối xoay gió theo kiểu mô hình này, thì bạn đừng làm quá nhiều cánh quạt, nên cắt cái thùng đó ra làm 3 cánh thôi để chúng cách nhau 120 độ 1 cánh trên hình tròn thì sẽ có hiệu suất cao nhất. Vì khi gió thổi qua bất kì mọi hướng thì gió thổi vào 180 độ của mô hình điều này gió đẩy 2 cánh quạt trong 180 độ của nó còn 1 cánh còn lại đi ngược chiều. Giả sử bạn làm 10 cánh thì thì tỉ lệ cùng chiêù là 5 , ngược chiều là 5 , giờ thì lực gió còn lại chỉ là độ cong của cánh quạt ( tính vectơ ấy mà). các bạn có thể thử nghiệm . Tui cam đoan là 3 cách sẽ cho hiệu suất tối đa, nếu nhiều hơn thì nó nặng lại phản tác dụng. Bạn có thể sử dụng mô hình để làm bơm nước giếng thẳng đứng nếu trục của nó là hình xoắn ốc nằm trong 1 cái ống . 🤫
Weren't we supposed to run out of fossil fuels back in the 1970's? I've been hearing these false alarms all my life. Yet, here we are, discovering new oil and gas resources by the day, and developing innovative ways to get at them. So, relax, Occutard. We've got time.
If you consider CO2 a pollutant and not plant food, then yes, we should pollute. Oil is a wonder of nature. It's relatively easy to extract and refine, and the resultant fuels are highly energy dense and easily transportable. One theory is that the inner crust is an oil factory, continually producing oil, and as we've seen, replenishing previously exhausted oil fields. We should do practical things to remove the bad stuff from exhaust, but CO2 is not one to worry over.
Hurray! We're being green! I want to ride on my rainbow colored unicorn all over the country side and look at all the failed government sponsored solar and wind projects and sprinkle pixie dust all over them and make them sustainable, workable, and profitable! Yeah! Being green is just grand!
*All practical tests show that small wind turbines hardly generate any electricity. And only at costs above 1$/kWh!* There is hardly any wind near the ground. And it is also very gusty, which extremely reduces the lifetime of the turbines. If you don't have to be self-sufficient in electricity, you shouldn´t use small wind turbine, but install solar panels. *With solar panels, you can reliably generate electricity for about 5-10 cents/kWh over a period of 25 years!*
leave it bung out upside down sloping towards a container let gravity do its job overnight fumes will condense and fall out of drum most oil will light as vapour ,aint built one yet but cut a few barrels
THis is a non-best. Why? I am demension S. S=0,5mx1m=0,5m^2. Probably this oil-bottle may be cut 1mx0.15m blade. This radius r=1m, i use this s=Pi*R^2, it's have 3,14m^2. YOU SEE? vertical axis 0,5 or 3,14 horisontal???
aquí en Colombia alguien a fabricado uno como este y que resultados le ha dado, ya trabaja con pequeñas brisas o necesita instalarlo donde fuertes vientos, muchas gracias
Hi guys! If you want any further informations about our recycling windturbines, contact me: richardschultes@yahoo.com. We are still in a process of developing and upgrading our ideas. Thank you Andreas, you made a wonderful job with this video!!! Richard Schultes
This is very much like the variations on the Savonius rotor that i experimented with a few years ago - techniphilia.blogspot.co.nz/search?updated-max=2012-10-19T23:20:00-07:00&max-results=1&start=8&by-date=false
Yay! I couldn't have said it better. He talks about innovative ways to get at the oil and gas but yet fails to see the future in green energy. We as a country have lost our way when it comes to being in the lead as far as energy technology. Look at Germany. They are 40 years ahead of us and every day we get farther and farther behind. I'll tell you who to blame....it's people like him.
This appeals to me. I'm really interested in lowering my electricity bill and this seems like a good bet because it wouldn't cost much to build one of these in my backyard since its very windy there. My only concern is with certifying this operation. In order to be considered a micro producer of electricity in Portugal my power company sends needs to certify the equipment and approve my ability to sell them my generated power, and since this is a homemade "power plant" would they approve this?
This could also work as an affordable homemade outdoor airfiltering technique, for contaminated atmospheres .It could use pollution absorbing paint and aircleaning filters that can be washed off.,for dual useage.
MAte you know that that barrel could have blown up in your face if there were some gasoline or oil fumes left in it? Could be wise to inform ppl before they try .
pas mal comme réalisation, j'envisage de la faire avec un alternateur de camion 24V 6OAMP je suppose que les panneaux oscillants le sont sur des axes soudés a la baguette; je m'inquiète du bruit de cette ensemble pouvez-vous préciser le nombre de db ?.tout autre précision sera le bienvenue.
Just found this amazing open-source-product and answer to the question of energy autonomy for the poorer half of humanity. Is there any possibility to also spread the AutoCAD-files further than in the training-video. Could we get the original file too to not reinvent the wheel? And last question: What is your experience with the forces on the bearings of vertical turbines?
Great and simple design. I want to build this for our fishing house at lake. can you send me a measurments for bearings and shaft assembly. Gonna send you full vid and photos of done Gwindoline instaled on lake. send me a mail to contact you..
install more of these in all valley and off shore coastal ocean in javania seaport and build more turbine canals to energize all asia pacific as charity humanitarian efforts to help all civilian to get clean eco safe energy.
подшипники НЕ нужны, генератор НЕ нужен, ремень, провода- это всё потери на трение и тепла!!! ось притормаживать колодками и пользоваться напрямую теплом от трения. регулятор Уатта и теплоноситель вода решают проблемы автоматизации.
It's able to produce about 300 Watt. It depends on the wind. But it’s enough to charge normal car batteries and so you can consume a lot of energy in a short period. And it’s surely enough to start your computer for 2 hours a day, or to charge a mobile, or to have light for reading the newspapers and to have a look at your pretty wife.
no no no, it did not may 300w(need very high speed 13>m/s). This area blade very small. Max 10-15w. NOT 300w
It's been close to an decade how is the wind turbine now
I have all the parts & tools for this build except blue paint :(
I love it ! Simple design, hats off to you ..
We used an old alternator from a Simca 1000. We assume a useable power of min. 200W in winds about 15-20mph. Our idea has two goals. At first it is a drawing sample in a new AutoCAD 2011 training-video. These videos will be seen millions of times all over the world. This chance is us our second goal. We found that it’s very easy to build and the materials can be found on auto graveyards all over the world. We hope that lots of people will use this construction and build their own Gwindoline.
Welcome Friends, 100.000 views - I thank you all. Especially your interest in green energy is warming my soul and gives me hope for the future.
A main brain in developing these turbines is my friend Richard Schultes.
So if you have technical questions, please write to richardschultes@yahoo.com.
Greetings from Vienna.
--- Only the globalization of information has the power to save our planet ---
busque,busque y busque y me encontre el mejor video ,referente a una turbina eolica casera,,,magnifico insuperable ...gracias...
Can I get the AutoCAD file? Please
Can any one suggest that any open source software to test wind turbin design in simulation
Awesome video. Because there are power cuts in Ukraine, perhaps you can print 1000 instruction sets and send it to some ukraine addresses for distribution? Thee don't have the interweb most places.
лучший ветрогенератор!!! VERY GOOD +++5!!!
Brilliant idea. I would add a cap over the upper bearing to protect it from rain and rusting. A similar project of mine some thirty years back produced horrible noises after a short while.
I had thought of a vertical wind turbine similar to a biscuit fan, and wondered if it had been done by someone...great design with the barrel! There seem to be many advantages over the typical "pinwheel" design...the flickering of sunlight that bothers some people should be much less...also, it has to be safer for birds, and more durable...also, no need to face it into the wind, as it is always able to catch wind from any direction. Another idea I had has to do with the generator. I thought of a design where the distance of the fixed magnets from the rotor can be varied. In light winds, the magnets could be more distant from the rotor, allowing free rotation and the production of some electricity, however little. As the wind increases, the magnets, by means of a governor (either mechanical or electronic), could be brought closer to the rotor, producing more current, and acting as somewhat of a brake so that the turbine doesn't spin too fast. However, I don't do any of this, just think about it.
Amazing simple design buildable by almost anyone
This will never work. . ..The power output would be so small that it would be a huge waste of money.
A car alternator spins at a min of 1000 rpm and its power output becomes maxed out at a much higher rpm.
1000 rpm is approx 170 rpm per second.
.
What you have done, is taken a slow turning trashcan that may reach 20 rev per second at its very best in
high winds, and stepped it DOWN about 10 to 1 to the alternator. This will turn the alternator slow. Not enough
If you get more than15 or 20 watts out of this thing, I think you will be doing extremely good.
What looks good on paper doesn't mean reality is there.
Great design, but non-functional. You have here a nice spinning ornament that looks cool and fools
the fools that want free energy
Can you provide me efficient design for low torque turbines
@@arifcrafts3961
First you need a generator/alternator rated at the voltage you are using.
Second you need the alternator to be turning at least idle speed. .. 1000 rpm.
Third. How fast does your vertical turbine turn? 10rps? That's very fast.
Probably 5rps in a high wind. 3 rps is closer to reality. That is 180rpm.
Forth. You need 1000rpm but have 180rpm. That calls for a 6:1 pully ratio.
Fifth. What i said above is all based upon a system with no load at all. With a load, that rpm will be slowed down to maybe 2rps. Which slows down you genetator to about 700 rpm.
Just because it is turning, doesnt mean it is charging batteries. It takes about 16 to 18. Volts to charge a 12v battery.
There is a huge reason why sellers and makers do not post windspeed vs power output. Because it takes a huge amount of wind just to get adequate power from the turbine
Further down in the messages, the writer corrects someone and says he got 10 to 13 watts of power, not 300. This correction sounds about right. 10 to 13 watts of power.
very good this easy amazing
The biggest difficulty I think would be to build this perfectly balanced and symmetrical turbine to reduce the vibration that is common in this type of vertical axis turbine.
Very nice, thanks for posting. I think that these uni-directional wind turbines from re-purposed hardware are the way to go for the majority of us who don't have the funds for the fancy store-bought stuff.
That Is the best and strong, idea.
Não deixe as aletas fixas!
Coloque um eixo em cada uma para que elas se movimentem independentes, abrindo a favor do vento e fechando contra o vento
Com isso vai diminuir o arrasto aerodinâmico aumentando a eficiência.
Mas o projeto é show por ser simples e eficaz.
Parabéns!
The wind generator looks very professional.
Ok, but how about a video showing it working with a load.
Very nice 👍
How elementary school is tolerable. The problems are: too heavy, no brakes, which will cause a fire or at least a generator failure...
ممكن التفاصيل والمقاسات
Saludos de Joacin Montoya inventor de ESCRITURA GLOBAL. Con una gran idea electronica donde todas las personas MUDAS ban a poder HABLAR y en muchos idiomas del mundo.
Love the virtual v actual, can’t decide which is more awesome!
😎👍🏼😎
Ini nampak bagus dengan sedikit tiupan angin akan memenuhi harapan untuk mendapat putaran yang lebih,Anda hebat
Brilliant, free power. May the wind forever blow on your turbine !
Sounds a bit perverse and personal 😁😁😁
very nice my friend
hello, sir would you please tell me the output from the Generator? if you have no problem, please send me the project description file. I will be very grateful to you. Thank you
Why do all these tech videos have the most horrible music?
Stupid music!!!!!!
How mamy Watts?
Nice work, especially the proper CAD modeling and the use of 5 sails. I am a bit concerned that it will flutter in strong winds... If so you might want to add support to the sail ends. I am basing this on experience - my dad and I built something very similar when I was a kid, using 3 aluminium sails, and the bearing and main pully from a washing machine drum - Looks like you also used a washing machine drum pully?. We mounted it around 5m up on a steel pole anchored to the ground. I like Savonius turbines because they are simple and easy to make.
Thank you. Your video is very cool and useful. My name is Thien Hung, I am in Vietnam. Glad to be friends with you.
Too labour intensive.....just cut the barrel in half axially and join the 2 halves at the edges to the centre pole.......job done.
But then you have to be real careful the barrel is cut exactly in half or it won't be in balance
could be used on a boat for a paddle wheel on the sides and back. to generate electricity in a creek. weld sprockets form old bike and make one big chain drive.
Where can I find a design for maglev windmill???
Here on YOuTube
The bearings and the shaft must suit each other. We used a 60mm-pipe from a building scaffold. The two “square flange mounted bearings” can be easily bought in different shops for mechanical parts. Search for a local dealer on google. When you finished the assembly you have to balance it. For this put the whole thing in a horizontal position and look where turning stops. On that side reduce weight until it stops without turning back. For further details contact me: info.at.computerstall.ch
Now you can download the blue-prints on www.CADdok.com
irp-cdn.multiscreensite.com/3bb20d5a/files/uploaded/Konstruktionsplan_CADdok-PDF.pdf
Mujhe bahut achcha laga ye power janred k
Only one-quarter right. I'm a pragmatist, not ignorant. And I'm more on the libertarian side of the Republican Party. I don't believe the central planners should be wasting tax payer money on expensive and unreliable "alternative energy" projects that are largely owned by Obama bundlers/campaign donors and usually end in bankruptcy while said bundlers/donors walk away with golden parachutes. The USA is the Saudi Arabia of natural gas and shale oil/tar sands. That's where we should be focusing.
👌
What did you use as generator? Is this a engine from a washing mashine?
Okay. This tit-for-tat is getting ridiculous. We need to end it sometime soon and go on with our lives, but my grand children will be paying crushing taxes to pay for the boondoggles of present. You get the last word.
Great invention. It really is that simple, although... the materials are a little heavy. On a light breezy day you would miss out on generating power. So although wonderfully designed, not at optimum efficiency.
God bless
Nếu bạn muốn tăng hiệu suất của cái cối xoay gió theo kiểu mô hình này, thì bạn đừng làm quá nhiều cánh quạt, nên cắt cái thùng đó ra làm 3 cánh thôi để chúng cách nhau 120 độ 1 cánh trên hình tròn thì sẽ có hiệu suất cao nhất. Vì khi gió thổi qua bất kì mọi hướng thì gió thổi vào 180 độ của mô hình điều này gió đẩy 2 cánh quạt trong 180 độ của nó còn 1 cánh còn lại đi ngược chiều. Giả sử bạn làm 10 cánh thì thì tỉ lệ cùng chiêù là 5 , ngược chiều là 5 , giờ thì lực gió còn lại chỉ là độ cong của cánh quạt ( tính vectơ ấy mà). các bạn có thể thử nghiệm . Tui cam đoan là 3 cách sẽ cho hiệu suất tối đa, nếu nhiều hơn thì nó nặng lại phản tác dụng. Bạn có thể sử dụng mô hình để làm bơm nước giếng thẳng đứng nếu trục của nó là hình xoắn ốc nằm trong 1 cái ống . 🤫
Weren't we supposed to run out of fossil fuels back in the 1970's? I've been hearing these false alarms all my life. Yet, here we are, discovering new oil and gas resources by the day, and developing innovative ways to get at them. So, relax, Occutard. We've got time.
Bearing looks strong enough to handle a second unite on top giving twice the power at the same RPMs. I LIKE IT.
Eventually, "no more energy"???? What planet are you from? The same planet where millions in wasted tax payer money is considered "free." Oh brother!
ты амперы покажи !!!!!!!!!!!!!!
If you consider CO2 a pollutant and not plant food, then yes, we should pollute. Oil is a wonder of nature. It's relatively easy to extract and refine, and the resultant fuels are highly energy dense and easily transportable. One theory is that the inner crust is an oil factory, continually producing oil, and as we've seen, replenishing previously exhausted oil fields. We should do practical things to remove the bad stuff from exhaust, but CO2 is not one to worry over.
It has to be blue...
Sebuah Penelitian Yang Spektakuler........Bombastis............Belum Pernah Terpikir...........
Hi! Very nice video! How much power did you produce from it, if at all you fixed the generator?
هاته الفكرة من ابتكار عربي سوري تحيا من المغرب
We used normal pillow block bearings, which are ready for installation.
Greetings from Vienna
Минимум материала. Дёшево и сердито молодцы.
make a small wind turbine صنع توربينات الرياح الصغيرة
amazing!, thanks for posting i learned something from this video.
Love you men!! really great work with perfect planing and nice tools include software!
Are you serious?!! :D :D :D Amazin'.
Hurray! We're being green! I want to ride on my rainbow colored unicorn all over the country side and look at all the failed government sponsored solar and wind projects and sprinkle pixie dust all over them and make them sustainable, workable, and profitable! Yeah! Being green is just grand!
thanks dude this is genius idea
make sure the gas is purged before grinding!!!!!! it could explode!!!!!
*All practical tests show that small wind turbines hardly generate any electricity. And only at costs above 1$/kWh!*
There is hardly any wind near the ground. And it is also very gusty, which extremely reduces the lifetime of the turbines.
If you don't have to be self-sufficient in electricity, you shouldn´t use small wind turbine, but install solar panels.
*With solar panels, you can reliably generate electricity for about 5-10 cents/kWh over a period of 25 years!*
APA!
Ez b. primitív.... annak ellenére hogy a CAD-ot jó közepesen használod.
Mondjuk a középnyugatra elég.....
really great- im in hungary are you near Wien?
واو .. روعة !! بس من وين أجيب القطعة البكره الكبيرة التى في الأسفل على البرميل
Never use this type of cutting equipment on empty diesel storage barrels. The barrel will still have an air-diesel vapour mixture which is explosive.
leave it bung out upside down sloping towards a container let gravity do its job overnight fumes will condense and fall out of drum most oil will light as vapour
,aint built one yet but cut a few barrels
Good advice, well done
How much power did you get out of it? Was there a generator on the real thing?
Pretty useful information simple and easy , nice done.
По чём бочка😇
I just hve one question: How does it perform under heavy rain?
what holds the shaft in the bearings? I didn't see a press fit.
Thunkful2 most bearings have either set screws or a locking ring
THis is a non-best. Why? I am demension S. S=0,5mx1m=0,5m^2. Probably this oil-bottle may be cut 1mx0.15m blade. This radius r=1m, i use this s=Pi*R^2, it's have 3,14m^2. YOU SEE? vertical axis 0,5 or 3,14 horisontal???
aquí en Colombia alguien a fabricado uno como este y que resultados le ha dado, ya trabaja con pequeñas brisas o necesita instalarlo donde fuertes vientos, muchas gracias
congratulations Edéia, anything that can help our planet, is always welcome.
Hi guys! If you want any further informations about our recycling windturbines, contact me:
richardschultes@yahoo.com. We are still in a process of developing and upgrading our ideas.
Thank you Andreas, you made a wonderful job with this video!!!
Richard Schultes
This is very much like the variations on the Savonius rotor that i experimented with a few years ago - techniphilia.blogspot.co.nz/search?updated-max=2012-10-19T23:20:00-07:00&max-results=1&start=8&by-date=false
nice project, i only miss the generator in the final assembling
also watch:
ruclips.net/video/giaDZwSrdzs/видео.html
Yay! I couldn't have said it better. He talks about innovative ways to get at the oil and gas but yet fails to see the future in green energy. We as a country have lost our way when it comes to being in the lead as far as energy technology. Look at Germany. They are 40 years ahead of us and every day we get farther and farther behind. I'll tell you who to blame....it's people like him.
This appeals to me. I'm really interested in lowering my electricity bill and this seems like a good bet because it wouldn't cost much to build one of these in my backyard since its very windy there. My only concern is with certifying this operation. In order to be considered a micro producer of electricity in Portugal my power company sends needs to certify the equipment and approve my ability to sell them my generated power, and since this is a homemade "power plant" would they approve this?
This could also work as an affordable homemade outdoor airfiltering technique, for contaminated atmospheres .It could use pollution absorbing paint and aircleaning filters that can be washed off.,for dual useage.
MAte you know that that barrel could have blown up in your face if there were some gasoline or oil fumes left in it? Could be wise to inform ppl before they try .
coolest thing...meaning performance...softwear and shi*
pas mal comme réalisation, j'envisage de la faire avec un alternateur de camion 24V 6OAMP
je suppose que les panneaux oscillants le sont sur des axes soudés a la baguette; je m'inquiète du bruit de cette ensemble pouvez-vous préciser le nombre de db ?.tout autre précision sera le bienvenue.
Just found this amazing open-source-product and answer to the question of energy autonomy for the poorer half of humanity. Is there any possibility to also spread the AutoCAD-files further than in the training-video. Could we get the original file too to not reinvent the wheel? And last question: What is your experience with the forces on the bearings of vertical turbines?
Генератор от чего ?
GENERATOR ALTERNATOR 12 VOLTI,40 AH,AUTO DACIA 1300
bbagus sekali ikut belajar dalam pembuatan pompa air..
Great and simple design. I want to build this for our fishing house at lake. can you send me a measurments for bearings and shaft assembly.
Gonna send you full vid and photos of done Gwindoline instaled on lake. send me a mail to contact you..
Понравилось,молодцы👏👍
What's that kind of bearing called?
I have been fond of wind turbine and because of that I purchase one.. but I never seen a turbine like this.. hmmm I better make one..
Would not it be simpler to take a piece of galvanized tin and round it than to work a whole day just to break up a good barrel?
install more of these in all valley and off shore coastal ocean in javania seaport and build more turbine canals to energize all asia pacific as charity humanitarian efforts to help all civilian to get clean eco safe energy.
подшипники НЕ нужны, генератор НЕ нужен, ремень, провода- это всё потери на трение и тепла!!! ось притормаживать колодками и пользоваться напрямую теплом от трения. регулятор Уатта и теплоноситель вода решают проблемы автоматизации.
where did you get the bearings ...looks great ...how do you call these bearings...
Very Innovative . Hats off . After looking at many things on wind power - this was a cool idea .....Keep up the good work . Cheers
فكره جيده
geniaaal!!! muchas gracias!!!