How to - Dellorto Carburettor Service for Vortex Mini Rok - Power Republic

In this video, we take you through the steps to service the Dellorto Carburettor for your Vortex Mini Rok engine.
Don't forget to leave your questions or comments below and we will get back to you asap.
Check out our website www.powerrepublic.com.au for parts and information.

[@ryba13100]

Thanks you so much for your video. Regards from Poland :)

[@PowerRepublic]

cheers legend, thanks heaps for watchin'

[@russellcooper4169]

Thanks for the carby vid Dr. Power

[@PowerRepublic]

your very welcome Russell

[@timcoley6064]

thats awesome m8. will help mums dads new to the sport.nice job

[@deonwelman6989]

Hi Derek, great video. What is the fuel pipe loop on top of the carb. Mine faces down but with no pipe connected

[@PowerRepublic]

the breather tubes? we face them up and use a bridge piece of tube with a slot cut in the centre to atmosphere

[@fenceotago6813]

Great video
Is the float measure to the metal bracket or the plastic part
Cheers

[@PowerRepublic]

to the high point of the p[lastic floats is what I do. but either way is fine as long as you do it the same each time

[@fenceotago6813]

Cheers

[@user-zb4yx2lq3e]

Hey Dr Power. The updated mini rok rules have removed the fuel return line. The engine start fine when cold but if the young bloke spins on track it now won’t restart like it’s flooded (only since removing the return line). I’ve followed this video but still have the issue. Any tips? Cheers

[@matthewmarino9172]

Adjust the float mate

[@STSOPERATIONSTrafficCont-xx6ui]

How often does this need to be done if you are filtering your fuel and also run an inline fuel filter please

[@PowerRepublic]

if you are serious about winning, do a race prep before each event, inc carby service

[@BEFITtingImage]

Thanks for the video - how often do you recommend this?

[@PowerRepublic]

Hi Dave, merry Christmas mate. do it in between race meetings

[@kennethvillena7608]

help me what good set up for jettings and emotion tube and sprocket 😊 for minirok

[@andreicerebel]

Great video you can help me to understaind the mini rok phb18 carburator i want to do a corect carburation if you cant exolaind this carburator please

[@PowerRepublic]

sure can my friend, what exactly are you having problems with?

[@andreicerebel]

@@PowerRepublicWhat is the role of the needle in how you impoverish or enrich the carburetion and how do you know which jigler to put. When you tighten the screw, does it cut its fuel?

[@BEFITtingImage]

What are the other round gaskets in my carby kit, the needle housing is the newer screw in type so I get I Don't need the one in this video,

[@PowerRepublic]

nah, just throw em out, spares from another kit

[@bradellis6915]

Is this for cadet 12 or a restricted cadet 9?

[@PowerRepublic]

if your using the 97 jet in cadet 9 you can lean the float level off to 5.5mm instead of the 6.0mm for the cadet 12. best thing to do is to try them both with the same main jet and measure your results with a Lambda sensor. we also use a return line of the fuel outlet from the fuel pump back to the fuel tank with a 1-2mm restriction in the line.

[@steveclee565]

You mentioned the mixture screw wasnt at 3/4, is 3/4 your start point?

[@PowerRepublic]

Steve Clee I start at 3/4, 97maim jet and clip 4 on the needle for sea level tracks. As you increase your height above sea level you can lean the main jet out to a 95.

[@steveclee565]

Power Republic thanks & great videos!

[@PowerRepublic]

!

[@shrimpti1974]

Great vids! I know this is an older vid but can you just confirm where you measure the float level? It’s hard to see on video. I can see it’s from the seat, but is it to the top of the actual float or the metal arm? Cheers! 👍👍

[@matthewmarino9172]

Hi Derek, where do you get the kit from ?

[@PowerRepublic]

Hey Matt, you can email us and we can send them out next week

[@matthewmarino9172]

@@PowerRepubliccheers ,email address?