[GOOD TIP] 6:08 For better cleaning the radiator fins where dust piled at the fanning end you have to use soapy water dipped tooth brush and carefully clean those fin holes after vacuuming and removing big bust piles on the fins. Then use moist brushing second third times to remove the soapy moisture out fins with careful brushing, you will see a lot of dirt on the brush. Because micro dust particles settled on the fin surfaces and soapy water brushing after vacuuming will do 2nd stage better cleaning of fins so next time the dust wont settle inside the fins so frequently.
Hello, I've tried just about everything... I replaced the fan&Heatsink in a Dell 17-5767 Now the Fan is running wide open all the time... error message saying fan not responding correctly...In the bios the the fan isn't showing the RPM's...Any ideals? I've tried about everything...unplugged battery for 30 sec held power button for 30 second's...unplugged the small 2032 battery for 10 mins... Did the thermal paste over..unplugged the fan and plugged back up...reset the laptop...tried a old bios firmware...tried my old fan which still works,BUT IT ALSO runs at highest rpms now... Trying to think of everything I've tried...Did the new fan do some kind of hardware change???? Any way gonna order another fan and try that,I guess Thanks
check the connection wires of the fan. may be some wire has'nt connection (e.g. wich is responsable for RPM). Also check if the heatsink applies well on all the chips. it's difficult to see, but try. you can apply the thermal paste, place and screw the heatsink, and then remove it again and see if the thermal paste was pressed correctly on all the surface of the chip.
@@computerrepairservice2654 Hey Buddy that's what it was...The fan plug on the motherboard had a prong/pin for the blue wire broke,And luckily,I was able to solder the blue wire to the broke prong/pin....Doesn't look the best,But got it working...Thanks for trying to help..Take Care
is there any way to clean it without having all the parts removed like in this video? some laptops could jub be cleaned with compressed air near the vents, what about this 1564?
You can do it, but with this way the cooling system will be cleaned partially. Also the thermo-paste it's preferable to be changed at each cleaning. Also, if there is a few dust in a cooler, then it will be go off with the compressed air, but if there is a lot of dust then a piece of that can block the fan and the result will be not "so good".
What is the adhesive tape on white and black cabes from WLAN? That is important? Is it normal the cabe white and black be uncovered in that part? the tape is mettalic?
+Rodney Suhr if you talk about a little bit of the adhesive tape on 3:07 minute of video, it's for better fastening of the wires. It's a common cloth tape.
check if the flex cable from the power button is correctly connected to the motherboard. check also if the contacts at the cable's end are ok and are not destroyed.
Great video, thanks, you have a new subscriber , please my same laptop screen black, no normal working noise at hard desk, power on, dvd drive startup normal noise, switched new ddr3, didnt work, any ideas? Yet the fan get so hot after only 5 min.
May be deactivated. Look at the right-bootom corner in the notifications area. The bluetooth tab must be blue. Or you can download and install drivers from the Dell's website
+Javi Vente The only tools I've used are: a phillips screwdriver, a small flathead screwdriver, tweezers and a spatula, like those as the dentists are using.
I have the same laptop. I gave it to fix the CPU fan but when it came back the sound stopped working. I think the person who fixed the fan somehow managed not to attach the internal speaker wires. Which ones are those if you can point that out. I will take it apart and try to fix it myself on the same. Thanks.
I did manage to open the laptop today morning and just as i thought the laptop speakers weren't plugged in properly. Did that and now the speakers work.
Hi, I just did a screen ribbon replacement on my one of these as it was flickering then white screening ... After fitting the new ribbon however the laptop will not power on , Nothing even with cable in get nothing no lights nothing was fine this morning ... ??
may be the cable is not gut. also, check the connector on the motherboard - some times if the cable was not connected correctly, the pins inside the connector can bent and make short circuit. Are you sure that the fault is in the cable and not LCD panel?
Yeah, Its the cable screen is fine I fixed it once before but after use (screen open and Close) the issue has returned, hence the ribbon change .... Makes no sense to be dead after a ribbon change .. I am going to gut it tomorrow rebuild it .... After that Likely get a Hammer and finish up there to be honest ..... Was fine this morning cable arrived changed it now nothing ... Dead .. Thanks for the reply ..
Just got some lights ... a cable that i have not even touched pushed on a little its the power cable from the charger port ..... Rebuilding again now ....
+Ricardo Nunes it's a thermal compound paste, which is necessary to be applied between a processor (cpu or gpu) and the heat sink, a heat from the processor to be dissipated better.
thanks to his guidance, everything went well and I managed to reassemble the notebook ... with a few pieces left, they may not be important ... Thank you!
it's a thermal compound paste and yes, it is necessary to be applied between the processor (cpu or gpu) and the heat sink. You can obtain it from any electronics store.
Thanks bro. Changed my fan using this and all is well.
Very usefull!! This model of laptop is complicate to disarm. Thanks for the video!!
Thanks a lot great video bro.
The music is spot on !
[GOOD TIP] 6:08 For better cleaning the radiator fins where dust piled at the fanning end you have to use soapy water dipped tooth brush and carefully clean those fin holes after vacuuming and removing big bust piles on the fins. Then use moist brushing second third times to remove the soapy moisture out fins with careful brushing, you will see a lot of dirt on the brush. Because micro dust particles settled on the fin surfaces and soapy water brushing after vacuuming will do 2nd stage better cleaning of fins so next time the dust wont settle inside the fins so frequently.
Obrigado ajudou muito.
Thanks!
plz give me the solution of hinge broken of inspiron 1564
Obrigado me ajudou muito
Thanks bro
thank you
Hello, I've tried just about everything... I replaced the
fan&Heatsink in a Dell 17-5767 Now the Fan is running wide open all
the time... error message saying fan not responding correctly...In the
bios the the fan isn't showing the RPM's...Any ideals? I've tried about
everything...unplugged battery for 30 sec held power button for 30
second's...unplugged the small 2032 battery for 10 mins... Did the
thermal paste over..unplugged the fan and plugged back up...reset the
laptop...tried a old bios firmware...tried my old fan which still
works,BUT IT ALSO runs at highest rpms now... Trying to think of
everything I've tried...Did the new fan do some kind of hardware
change???? Any way gonna order another fan and try that,I guess Thanks
check the connection wires of the fan. may be some wire has'nt connection (e.g. wich is responsable for RPM). Also check if the heatsink applies well on all the chips. it's difficult to see, but try. you can apply the thermal paste, place and screw the heatsink, and then remove it again and see if the thermal paste was pressed correctly on all the surface of the chip.
@@computerrepairservice2654 Thanks Tried it all just about I may have damaged the motherboard someway...
@@computerrepairservice2654 Hey Buddy that's what it was...The fan plug on the motherboard had a prong/pin for the blue wire broke,And luckily,I was able to solder the blue wire to the broke prong/pin....Doesn't look the best,But got it working...Thanks for trying to help..Take Care
Amazing video! Thank you. Is the heat sink and thermal paste procedure crucial?
No not butit can explode but don't worry you legs will be safe
is there any way to clean it without having all the parts removed like in this video? some laptops could jub be cleaned with compressed air near the vents, what about this 1564?
You can do it, but with this way the cooling system will be cleaned partially. Also the thermo-paste it's preferable to be changed at each cleaning. Also, if there is a few dust in a cooler, then it will be go off with the compressed air, but if there is a lot of dust then a piece of that can block the fan and the result will be not "so good".
What is the adhesive tape on white and black cabes from WLAN? That is important? Is it normal the cabe white and black be uncovered in that part? the tape is mettalic?
+Rodney Suhr if you talk about a little bit of the adhesive tape on 3:07 minute of video, it's for better fastening of the wires. It's a common cloth tape.
Hello! I have everything done as in the video, unfortunately, no longer starts. Where can the problem be?
check if the flex cable from the power button is correctly connected to the motherboard. check also if the contacts at the cable's end are ok and are not destroyed.
U only apply paste on processor, but u don't apply any paste or thermal pad on GUI or any thing , thermal pad attached to that portion
Great video, thanks, you have a new subscriber , please my same laptop screen black, no normal working noise at hard desk, power on, dvd drive startup normal noise, switched new ddr3, didnt work, any ideas? Yet the fan get so hot after only 5 min.
Laptop updated to Windows 10, but Bluetooth was not found. What's the solution?
May be deactivated. Look at the right-bootom corner in the notifications area. The bluetooth tab must be blue. Or you can download and install drivers from the Dell's website
Same issue here, no drivers on dell's website, only with external module I could use bluetooth
Didn't really clean or lubricate the fan
ありがとう！PCが治りました！！
I followed this video and everything was fine until i turned my laptop on and i realized that my keyboard is no longer working, anyhelp?
disconnect/reconnect keyboard to motherboard
@@computerrepairservice2654 already did tried that but still not working
check if the contacts on the flex-cable are ok. also check if the connector on the motherboard closes well.
What are the list of tools I need? Especially the tool you used to remove the wiring?
+Javi Vente The only tools I've used are: a phillips screwdriver, a small flathead
screwdriver, tweezers and a spatula, like those as the dentists are
using.
I have the same laptop. I gave it to fix the CPU fan but when it came back the sound stopped working. I think the person who fixed the fan somehow managed not to attach the internal speaker wires. Which ones are those if you can point that out. I will take it apart and try to fix it myself on the same. Thanks.
There are two speakers. I disconnect them at 4:38 and 4:47.
I did manage to open the laptop today morning and just as i thought the laptop speakers weren't plugged in properly. Did that and now the speakers work.
Hi, I just did a screen ribbon replacement on my one of these as it was flickering then white screening ... After fitting the new ribbon however the laptop will not power on , Nothing even with cable in get nothing no lights nothing was fine this morning ... ??
may be the cable is not gut. also, check the connector on the motherboard - some times if the cable was not connected correctly, the pins inside the connector can bent and make short circuit. Are you sure that the fault is in the cable and not LCD panel?
Yeah, Its the cable screen is fine I fixed it once before but after use (screen open and Close) the issue has returned, hence the ribbon change .... Makes no sense to be dead after a ribbon change .. I am going to gut it tomorrow rebuild it .... After that Likely get a Hammer and finish up there to be honest ..... Was fine this morning cable arrived changed it now nothing ... Dead .. Thanks for the reply ..
Just got some lights ... a cable that i have not even touched pushed on a little its the power cable from the charger port ..... Rebuilding again now ....
still the same.. Stripped it again removed screen cable and mini earth lead now the charger light is green ... Progress :D
OK this thing is beeping hard ..... NEW screen ribbon faulty perhaps ... ??
That looks painful.
Thanks
Thanks, great!
what is the "thing" that you used some drops on the 7m 12s?
+Ricardo Nunes it's a thermal compound paste, which is necessary to be applied between a processor (cpu or gpu) and the heat sink, a heat from the processor to be dissipated better.
thanks to his guidance, everything went well and I managed to reassemble the notebook ... with a few pieces left, they may not be important ... Thank you!
And if I don't have that..???
that paste you used, is it necessary? cuz i dont have it...
it's a thermal compound paste and yes, it is necessary to be applied between the processor (cpu or gpu) and the heat sink. You can obtain it from any electronics store.
lol
how much would something like this cost at a computer repair shop?
it depends on the country, city, and even from the repair shop you choose. I charge this work 30€+VAT (Greece).
@@computerrepairservice2654 +/- the same here in Brazil, I charge R$ 150,00. Depends of notebook model. Great video!
Thanks thanks thanks
I guess the process is the same for inspiron 1464??
the probability to be the same is great, but I'm not 100% sure.
Computer repair & service yes, the same process. I've done it successfully. Thank you.
What's that music?
My 6 year old inspiron1464 heats up within an hour...
I recommend to clean your laptop at least 1 at year