Derbi senda 50 / Aprilia sx 50 engine rebuild part 3 (D50B0 euro 3)

[@rudolfs450]

Yo I don't get comment notifications from older videos, so if you have any questions, join the discord and I will happily answer. on top real discord.gg/AXERGfJFKs

[@who.is_tica]

7:19 there, under the case,between gear selector and case, was a little bearing ball?i have the 2 washers but when cases are together, mine is stuck.don t rotate. please help me bro

[@slaider-garage]

you have to put many gaskets between crank cases

[@mvalentin4176]

Does the ignition just teleport on?

[@christermannen]

Yes

[@rudolfs450]

Yes

[@elbertodo224]

me llama la atencion que solo lleva oring en la culate del cilindro.saludos

[@smb9681]

Very helpful

[@growgamer-dz3ul]

Nice video

[@liamwallace2121]

Do you have any suggestions on how to get the clutch arm back in mine wont slide all they way down to be able to twist into position

[@rudolfs450]

Just twist and push it down till it gets in place idk

[@harryesteves387]

I need to put a new top end on mine... would you recommend taking the tank off and doing it with the engine still installed the bike, or take the engine out? how hard is it to take the engine out?
EDIT. engine is out.
Do u havea vid on setting up the rigging of throttle, and clutch?

[@rudolfs450]

I dont. if this is still relevant you can send the problem in discord

[@mercedes_w211]

labs vecit

[@CarFacts8]

One thing, I have installed the clutch cam in the same way, it does exactly the same as in the video and when I installed it I tried it and it doesn't engage. I don't know if you could help me.

[@rudolfs450]

Clutch doesnt engage, or the rod?

[@ugwd4369]

Hello, I have a question. How do you tighten the head screws?

[@rudolfs450]

@@ugwd4369 just hold it and tighten. Big nuts to 15nm and small bolts to 8nm

[@nobodyonline8454]

Can someone please explain to me why my clutch rod isn't going all the way in?

[@rudolfs450]

Just twist it till it goes in

[@nobodyonline8454]

@@rudolfs450 i tried but a good amount of the rod stays outside and it doesnt rotate

[@nobodyonline8454]

I figured it out
The top of my clutch was the wrong way in lmao

[@rudolfs450]

@@nobodyonline8454 bruh

[@lethal8801]

Is that a woodruff key on the clutch gear?

[@rudolfs450]

What is a clutch gear💀

[@ciekawymokiem2469]

Hi. i have a derbi senda with euro 2 engine. Will most things be the same as in your video or are euro 2 and euro 3 very different?

[@rudolfs450]

Pretty much same engine idk

[@jontedoesyt4984]

i instaled my oil seals to the crankshaft bearings to far in i think is this bad?

[@rudolfs450]

Yes, the bearings will seize up. My friend had that happen

[@Nico-gg4oq]

hi, my d50b0 engine has 3k kilometers so its pretty new and stock, but it doesnt shift well after a 3 month stand still, a few days ago it suddendly shifted normal which was really cool but now it only shifts 1-2 and sometimes Neutral, what can it be? yes i drove all 6 gears already

[@rudolfs450]

change the oil maybe idk

[@Nico-gg4oq]

@@rudolfs450 found the problem it was the shift gear shaft

[@Lloyd667]

​@@Nico-gg4oq what was wrong with it? I have the same problem

[@Nico-gg4oq]

@@Lloyd667 you’re a lucky man: I found the problem after spending too much time on looking for the failure online like you probably and changing spare parts i just changed the shifting rod to a new rod (Schaltwelle auf deutsch) for 50€. It was totally bend and worn out. 6 Months wasted time thanks to a 50€ fix 😂.
Grüße aus Deutschland

[@Lloyd667]

@@Nico-gg4oq gotta check it, thanks

[@iTzMxrio125]

Why did you install the old piston?

[@rudolfs450]

because the old one is fine

[@iTzMxrio125]

@@rudolfs450 ok

[@veke05]

volume warning 21:14

[@Buddha06]

pretty big cylinder if it was 50cc

[@rudolfs450]

Its a 70cc

[@lauritervonen6507]

lean