I’ve found that using a short piece of flexible 1/2 inch irrigation pipe works great to drain the oil on my time master. I’d recommend also a hour meter/tach to keep track of maintenance and to ensure your motor is at the proper RPMs.
I dont see in the manual where it states 60lb torque for tightening the mower blades ... where did you find this? Maybe its not in the paper manual and online?
Jimmy, thank you for the instructions. I have a couple of questions if you don't mind answering. I'm seriously thinking of buying this model at Home Depot. Do those blades come with the mower, and do you tilt and clean the bottom deck after each use? I ask this because I've always cleaned the bottom. I had a friend who never cleaned her mower and the deck became rusty and eventually created rust holes. Also, why did you sharpen the blades after 5 hours? Finally, since this video post, how do you like the mower so far? Good quality? Any issues? Thank you so much.
Yes the mower comes with mulching blades standard and they work very well. I choose to sharpen the blades several times throughout the season, and since I was changing the oil anyways, it was a good opportunity to just get it done. I actually just posted a full review if you like. It’s the most recent video on my channel. Happy to answer any other questions. Feel free to reach out anytime.
Just got my Time Master today. Funny story....Got home and was ready to put that bad boy to work. Cranked him up and started mowing. All of a sudden the trimmings were going every where. Out the sides, top and back. I was like this can’t be right, this is how it mulches?!....and just continued to finish mowing. Come to find out my local dealer forgot to give me the damn mulch plug. I had the bag and side discharge but no plug. 🤦♂️
1 quart is actually 32 oz. So if you started with a full quart you should only pour in oil until it’s at the 14oz line. If you started with a full quart you may have overfilled.
Thanks! Yeah I checked along the way and made sure not to over fill. I checked again the next day as well. Appreciate your comment and you watching my videos!
I just purchase my timeline mower, I use my air compressor with a 2' air wand to clean out the bottom of the deck after each time I use it. I think it would be much easier to remove the blades before cleaning off the build up of grass. Did you balance your blades off camera after sharpening them, if not your asking for premature bearing wear in due time. Thank you for the video..
Hey Rob. This video is a bit outdated as I have upgraded some tools. I currently use a Milwaukee angle grinder with a 60 grit flap disc to sharpen my blades.
Do you think it's better to change the oil in the fall, OR in the spring right before you start using it? I would think that would keep the oil fresher perhaps, not putting it in till you're about ready to use it. You don't actually sharpen the blade every time you change oil do you? Great video, thanks, keep posting any new discoveries, hacks, disappointments, repairs etc. I've only used mine about four times and it often makes slight rattling noise, not sure what is causing the ting ting ting ting ting, but without being able to diagnose it it's not easy to justify any repair service. Any idea what might be causing this?. Did you purchase the extended warranty? I never go for those things, having read that they are usually not worthwhile.
@@infinityandbeyond2386 thanks! Good to know it's nothing serious, and as long as the key ignition works hopefully I won't even have to pull that rope. Wonder if Toro would compensate in anyway, mine is only a couple months old.
Quick question, but not about the sharpening or the oil change....On my mower, that flap in the back lasted about a year and a half. If I back up it gets turned or something and then starts splitting, and then part of it gets caught underneath. Next thing I knew I'm cutting pieces of the flap! I bought a new flap, but I'm hesitant about putting it on. Do you know why this would happen? Seems like an odd design! Thanks!
@@normanortega3439 Ugh. I ran to the dealer where I got it (and there’s a bunch on display in their showroom) and they told me there was no drain plug. Told me to simply run it out of gas, remove the dipstick, tip the machine and it’ll dump out. So I did that. I wish I could see a pic or video of the drain plug you speak of. I’d be psyched!!
People talking about a drain plug: Is there an illustration or image somewhere online where I can see exactly where the drain plug is? I have this exact model but can’t find it
Hey buddy got a question. Changed my oil today just like you. It was my first oil change on this machine. Waited about 5 minutes after sitting her upright before trying to start her and she won't fire up. Engine seems locked up completely. Pull start won't budge.... What gives? I'm so confused.
Jimmy, i was wondering I think you had 8000 sqft in the back and im not positive about the front but are you able to cut your front and back on one tank? I herd a lot of complaints about tank size and just trying to get a feel for how many sqft I can cut on a tank.
Yeah so about 12000 sq feet total. If I can mow continuously without really stopping and letting the engine idle too much I can do it on a full tank. Did it yesterday actually.
FYI. I Clean my lawnmower after every time I cut the lawn, the reason I do this is because it is easier to hose to the grass off with water than using a scraper to scrap off grass from underneath, by using your your scraper you are also creating Scratches that later can possibly create rust under your lawnmower. This is just a friendly suggestion. Trying to help you save your investment. ✌️👍
I seen a video that the guy put blocks under the wheels so when he tips it over to drain oil, it’s higher and can tilt even more to drain better. Hope this helps👍
I clean it out any time I sharpen the blades. Typically 2-3 times during the mowing season. Hose hookup is personal preference. I find it’s just messy, personally.
Thank you. Just sharpened the blades and gave it a bath the other day (got a funny video clip of it too - coming soon 🙂) I bought it from the Home Depot.
You can. But I wouldn't recommend it. If there is a leak in the cap or the cap isn't properly secured, then the gas will leak out when the mower is tipped, and there is also a chance of flooding the motor. Best to just do it on an empty tank and play it safe. You can even keep the mower upright and pump the oil out. I may try that in the future.
@@SinnerSince1962 its easy, takes a second, just clamp a screw driver on your vice and hang the blade, whichever side is heavy, file a little on 'the opposite side' until the blade rests even, parallel to the ground. Simple.
Watch the video before commenting, he removed the spark plug wire. Can't tell you how many videos I watch where people ask questions or make comments without watching and listening to whole video.
I think he's got the electric start model. Ya dont want that starting accidentally. Plus when turning the blades it could also cause the mower to start. Then bye bye hands and hello hire-a-lawnservice company.
Sorry to hear that. A good impact driver should break it loose. I've found the first time breaking that bolt loose on any mower has been the most difficult.
If the mower is tipped the other way, onto the other side, then the oil spills out and soaks into the air filter, requiring the purchase of a new air filter even if the old one was clean.
Let's say it together, blade balancing. Blade sharpening. Not once did he check to see if it was sharp. Just cleaned off the bevel with his Harbor Freight sander.
Thanks for your time. Great video. Next year your son will be able to do it... . My son is 32 and he never has... wish you better luck..
Always smart to read the manual when it comes to mowers and other small engines and stick to the maintenance schedule.
For sure. I love that I can have it in pdf form as well. It's much more easily accessible.
I’ve found that using a short piece of flexible 1/2 inch irrigation pipe works great to drain the oil on my time master.
I’d recommend also a hour meter/tach to keep track of maintenance and to ensure your motor is at the proper RPMs.
Thanks for the recommendations! I'll keep those in mind! And thanks for watching.
I dont see in the manual where it states 60lb torque for tightening the mower blades ... where did you find this? Maybe its not in the paper manual and online?
32oz (not 30 as you stated) in a Quart, minus 18oz for the oil change leaves you with 14, not 12.
Jimmy, thank you for the instructions. I have a couple of questions if you don't mind answering. I'm seriously thinking of buying this model at Home Depot. Do those blades come with the mower, and do you tilt and clean the bottom deck after each use? I ask this because I've always cleaned the bottom. I had a friend who never cleaned her mower and the deck became rusty and eventually created rust holes. Also, why did you sharpen the blades after 5 hours? Finally, since this video post, how do you like the mower so far? Good quality? Any issues? Thank you so much.
Yes the mower comes with mulching blades standard and they work very well. I choose to sharpen the blades several times throughout the season, and since I was changing the oil anyways, it was a good opportunity to just get it done. I actually just posted a full review if you like. It’s the most recent video on my channel. Happy to answer any other questions. Feel free to reach out anytime.
My owners manual stated to turn mower with wheels up to drain oil not on side?
Best thing to do as soon as you finish mowing change the oil. The oil is hot and will flow
Just got my Time Master today. Funny story....Got home and was ready to put that bad boy to work. Cranked him up and started mowing. All of a sudden the trimmings were going every where. Out the sides, top and back. I was like this can’t be right, this is how it mulches?!....and just continued to finish mowing. Come to find out my local dealer forgot to give me the damn mulch plug. I had the bag and side discharge but no plug. 🤦♂️
Oh man 🤦♂️😂
1 quart is actually 32 oz. So if you started with a full quart you should only pour in oil until it’s at the 14oz line. If you started with a full quart you may have overfilled.
Thanks! Yeah I checked along the way and made sure not to over fill. I checked again the next day as well. Appreciate your comment and you watching my videos!
Enjoy your timemaster! I’ve had one for about a year now and it been solid.
You made the oil ratio on the bottle well said!
Hey Jimmy, how many oil changes did it take to fill up that container? And where did you dispose of it? Thanks for your help! 👍🏼
Good stuff Jimmy. She’s ready for more action now!
I just purchase my timeline mower, I use my air compressor with a 2' air wand to clean out the bottom of the deck after each time I use it.
I think it would be much easier to remove the blades before cleaning off the build up of grass.
Did you balance your blades off camera after sharpening them, if not your asking for premature bearing wear in due time.
Thank you for the video..
What do you do to balance your blades?
JImmy Lewis, what air tool and what grind wheel are you using? I just bought a Timemaster and like to keep my blades sharp. Great channel!! Sub'd
Hey Rob. This video is a bit outdated as I have upgraded some tools. I currently use a Milwaukee angle grinder with a 60 grit flap disc to sharpen my blades.
why did you sharpen the blades when it has only ran for like 5 to let say 7 hours?
Do you think it's better to change the oil in the fall, OR in the spring right before you start using it? I would think that would keep the oil fresher perhaps, not putting it in till you're about ready to use it. You don't actually sharpen the blade every time you change oil do you?
Great video, thanks, keep posting any new discoveries, hacks, disappointments, repairs etc.
I've only used mine about four times and it often makes slight rattling noise, not sure what is causing the ting ting ting ting ting, but without being able to diagnose it it's not easy to justify any repair service. Any idea what might be causing this?. Did you purchase the extended warranty? I never go for those things, having read that they are usually not worthwhile.
ruclips.net/video/Ie5RpNZorvU/видео.html check this video out
@@infinityandbeyond2386 thanks! Good to know it's nothing serious, and as long as the key ignition works hopefully I won't even have to pull that rope. Wonder if Toro would compensate in anyway, mine is only a couple months old.
Appreciate your thoroughness
Quick question, but not about the sharpening or the oil change....On my mower, that flap in the back lasted about a year and a half. If I back up it gets turned or something and then starts splitting, and then part of it gets caught underneath. Next thing I knew I'm cutting pieces of the flap! I bought a new flap, but I'm hesitant about putting it on. Do you know why this would happen? Seems like an odd design! Thanks!
No idea why that would happen. I’ve had mine get caught the wrong way many times and after 3 years I have no issues with it.
Scraping the grass under the deck is much easier if you tip the mower on it's side and use a garden hose.
Use the drain plug under motor towards the back, 1/2” socket extension square recessed piece of cake.
I knew that there will be a drain plug somewhere...
Wait. I have this identical mower. I’m looking underneath it right now. I don’t see the drain plug. Is it near the blades?
No frank, it's above the deck not under it
@@normanortega3439 Ugh. I ran to the dealer where I got it (and there’s a bunch on display in their showroom) and they told me there was no drain plug. Told me to simply run it out of gas, remove the dipstick, tip the machine and it’ll dump out. So I did that. I wish I could see a pic or video of the drain plug you speak of. I’d be psyched!!
Hey Jimmy, does that air compressor keep up with that grinder, or do you have to stop and let it fill up?
It keeps up okay, but it's not ideal. I'd recommend a bigger compressor for sure
Jimmy Lewis do you know what size the nut is on the mower blade? I want to use my impact driver to remove.
Great video. Is this a generic lawnmower oil or is there a type you recommend?
I like the Mobil 1 synthetic for my small engines.
You didn’t use the All American Sharpener to sharpen the blades? Good video by the way!
Well done brother! 👍🏻👍🏻👍🏻
What kind of oil you use?
People talking about a drain plug: Is there an illustration or image somewhere online where I can see exactly where the drain plug is? I have this exact model but can’t find it
Excellent video, sir. Thanks for empowering me to handle this myself for a change!
What kind of torque wrench are you using
Hey buddy got a question. Changed my oil today just like you. It was my first oil change on this machine. Waited about 5 minutes after sitting her upright before trying to start her and she won't fire up. Engine seems locked up completely. Pull start won't budge.... What gives? I'm so confused.
Oh man I don’t know. If it’s locked up I’d probably have somebody look at it. Never experienced that before.
Nice work, Jimmy!
Thanks!
Jimmy, i was wondering I think you had 8000 sqft in the back and im not positive about the front but are you able to cut your front and back on one tank? I herd a lot of complaints about tank size and just trying to get a feel for how many sqft I can cut on a tank.
Yeah so about 12000 sq feet total. If I can mow continuously without really stopping and letting the engine idle too much I can do it on a full tank. Did it yesterday actually.
So, there is no drain plug on the bottom of the engine? That sucks!
I know the gas tank it 1.2quarts but like is that like 2 soda of 20oz of gas or is me
FYI. I Clean my lawnmower after every time I cut the lawn, the reason I do this is because it is easier to hose to the grass off with water than using a scraper to scrap off grass from underneath, by using your your scraper you are also creating Scratches that later can possibly create rust under your lawnmower.
This is just a friendly suggestion. Trying to help you save your investment. ✌️👍
Congratulations
I like the little guy. My 2 year old grandson likes to watch me cut the grass.
I seen a video that the guy put blocks under the wheels so when he tips it over to drain oil, it’s higher and can tilt even more to drain better. Hope this helps👍
Thanks. How about this? Start at 4m48s ruclips.net/video/Ksp2kJaDaW4/видео.html
It has an oil drain plug.
There is a drain plug on it but you have to remove the engine to get to it, or once you find it you could drill a hole in the deck.
That would be cool if I could figure it out. Looking into pumps for next time. Thanks for the tip!
You do NOT need to remove motor to drain oil. 1/2” socket extension square. Towards back of motor.
Just a heads up on the left side of the mower there is a water hook up to clean the deck.
Yeah I know. Haven’t had much luck with it. Just makes a mess in my experience.
It seems you don’t clean your mower (under deck) after each mow using the hose hookup. Is there a reason I shouldn’t be doing that?
I clean it out any time I sharpen the blades. Typically 2-3 times during the mowing season. Hose hookup is personal preference. I find it’s just messy, personally.
So does it hold 18 or 12oz? About to do my first oil change on mine.
My manual says 18. Put oil in and then check with the dipstick until it’s between the lines on the stick.
@@JimmyLewisMows thanks man for the quick response!👍🏻
What weight oil did you use?
Thanks champion
Jimmy where did you purchase your timemaster(what store)?
Also after watching this video again you do a great job with the up keep of your mower..👍🏽👍🏽
Thank you. Just sharpened the blades and gave it a bath the other day (got a funny video clip of it too - coming soon 🙂) I bought it from the Home Depot.
Jimmy Lewis I look forward to seeing the video clip..😂
I couldn’t get the bolts off the blades. Tried wd40 and everything. Any ideas?
Impact wrench
Honest question, Can you change the oil like this with gas in the tank? Will there be any problems?
You can. But I wouldn't recommend it. If there is a leak in the cap or the cap isn't properly secured, then the gas will leak out when the mower is tipped, and there is also a chance of flooding the motor. Best to just do it on an empty tank and play it safe. You can even keep the mower upright and pump the oil out. I may try that in the future.
You didn't tell us what oil is recommended
I'm taking notes
I thought it was supposed to be 20 ounces for a full tank of oil?
Double check your manual. Mine calls for 18.
Do we need to recharge battery each time after mowing, after the first charge with AC outlet?
No batteries on this machine.
There is a plug underneath
You forgot to balance the blades when sharpening, but you did remember the 60 foot lbs of torque.
Balancing the blades.... LOL! Never done that in my life.
@@SinnerSince1962 its easy, takes a second, just clamp a screw driver on your vice and hang the blade, whichever side is heavy, file a little on 'the opposite side' until the blade rests even, parallel to the ground. Simple.
@@31acruz I just buy new blades
Watch the video before commenting, he removed the spark plug wire. Can't tell you how many videos I watch where people ask questions or make comments without watching and listening to whole video.
Preach!! 🙌 Thank you.
U love ur tools I can tell
Nice video!
Just changed my oil thanks
No anti-seize on the blade retaining bolts.
good video, always use a mask when grinding metal
GREAT
Why do you have to unplug the spark plug?
Safety precaution.
I think he's got the electric start model. Ya dont want that starting accidentally. Plus when turning the blades it could also cause the mower to start. Then bye bye hands and hello hire-a-lawnservice company.
What type of oil does toro say SAE 30 to 10w30?
Yes I believe that's what the manual says.
Do they require filter change?
Yeah I replace the filter when it’s dirty.
Nice video, although I wouldn't scrape the bottom with a metal scraper. Plastic.
What kinda oil are you using?
Mobil 1 synthetic 10W-30
Wesson Oil. Best on the market.
Dam for some reason my blades won’t come off my timemaster . Having trouble .
Sorry to hear that. A good impact driver should break it loose. I've found the first time breaking that bolt loose on any mower has been the most difficult.
@@JimmyLewisMows I Tried A Socket W/ Ratchet But It Was Too Tight So I Used The Impact. 💪🏼
What oil do I put in it
I use Mobil 1 10W 30 synthetic
Jimmy Lewis thanks you very much im going to auto zone right now
No oil drain plug!!??? How frickin' cheap can you get!??? What did that save in manufacture cost, 50 cents per mower...JHC!
Now that cutting out is a real pisser
Snap On! Dude, you don't cheap out on your tools, do you?!
I think it works better if you take the blade's off first before cleaning.
Balance the blades after sharpening them.
Yes.
2:10 for oil change start.
why not tip the mower the other way?
You should always tip a mower with the carb side up
If the mower is tipped the other way, onto the other side, then the oil spills out and soaks into the air filter, requiring the purchase of a new air filter even if the old one was clean.
never double tap when torquing
Thanks. I only do it for peace of mind. I have no intention of over-torquing or anything like that.
Biting my teeth waiting to see if he pulled the spark plug wire.... besides the fact he ran it out of gas prior to starting.......
I'll report him to connor if he doesn't!
2m10s into the video ya boogers!
@@JimmyLewisMows I see it now! You can never be too safe right?
Totally agree
10w30 full synthethic ?
Yes
i thought it was 20 oz of oil
Double check the owners manual. I went with what mine said and I double checked the levels to make sure.
@@JimmyLewisMows , it says 20 ounces. 😊
Nice video, thanks.
Nobody cares about your old mower....stop talking about it
No to the music
Blades are timed with that stupid toothed drive belt. Not very smart design for avarage home user.
Was considering one of these but the more I find our about it, the less likely that appears. Certainly not going to pay post-Biden price for it!
😂
Also you did not show nor tell the viewers how to DRAIN the oil. Kind of an important step to skip if you are going to do a video on changing the oil.
A pressure washer with a 60° nozzle would have cleaned the underside of the mower deck in like 10 seconds. Work smarter, not harder.
You’re right. But also need to work with the tools you have and live within your means.
You’re grade for this job is a C-. No blade balancing was done, unless those are self balancing blades.. If so where can we buy a set?😂😂😂
Let's say it together, blade balancing. Blade sharpening. Not once did he check to see if it was sharp. Just cleaned off the bevel with his Harbor Freight sander.
What oil were you using
Mobil-1 10W-30 full synthetic