Это видео недоступно.
Сожалеем об этом.

Nakamichi Dragon chewed the tape, how to fix

Поделиться
HTML-код
  • Опубликовано: 16 июн 2022
  • It was not simple to find a proper solution. The forum advice is incorrect. I have found an addon to the Nakamichi service manual and fixed the problem by following the Nakamichi guide.

Комментарии • 26

  • @patrickgajadhar5723
    @patrickgajadhar5723 2 года назад +3

    Good morning I am big fan of analog hifi I am not a technician but I always watch you videos. I hope you will make a lot videos in the future.

  • @Nakamichi_Service_UK
    @Nakamichi_Service_UK 2 года назад +2

    Thanks for sharing this issue and how to fix it. While I have yet to experience this issue, I’m sure I will at some time in the future and this will be a big help.

  • @Skydead1970
    @Skydead1970 10 месяцев назад

    Супер, спасибо за информацию ! Очень актуально для меня 🤝

  • @Mr.SuperNeze
    @Mr.SuperNeze Год назад

    Pemutar gigi roda kaset sebelah kanan terhenti. Sehingga menyebabkan bertumpuknya pita kaset pada penjepit roda karet sebelah kanan

  • @lmkan
    @lmkan 2 года назад

    Thanks a lot! Very helpful. What could be the cause of the 0.2 mm? Wear of the rollers?

    • @hifirulezzz
      @hifirulezzz  2 года назад

      I am not sure about a root cause, but Nakamichi had to change design to install adjustment arm on the rail to address it. earlier serial numbers does mot have that arm.

    • @lmkan
      @lmkan 2 года назад

      @@hifirulezzz That I understand but the machine left the factory adjusted to specs and someting changed. Must be wear. Could it be the rollers itself or mayby something else mechanical? I wonder..

  • @truongduong366
    @truongduong366 Год назад

    Mong bạn ra nhiều videos về chiếc máy này!Thanks!

  • @user-dw9zd3tx6w
    @user-dw9zd3tx6w 2 года назад +1

    Thank You !

  • @sh0t734
    @sh0t734 Год назад

    it would be ideal for the left pinchroller to touch even a bit faster than the right one (in reverse mode)

    • @hifirulezzz
      @hifirulezzz  Год назад

      How do you think this will affect direct playback? ;)

    • @sh0t734
      @sh0t734 Год назад

      @@hifirulezzz if the left pinchroller engages first on reverse playback , even if there was a bit of slack , it would be taken up by the left pinchroller and when the right pinchroller comes into contact it ll just "keep tension".

    • @hifirulezzz
      @hifirulezzz  Год назад +1

      @@sh0t734 Aha, but this will not help with the forward direction. So, that was a reason Nakamichi decided to make both pinch rollers touch capstan shafts simultaneously.

    • @sh0t734
      @sh0t734 Год назад

      @@hifirulezzz yeah that s true too.
      They could ve made it so in reverse left comes first and in forward right comes first but i guess it wouldve been to complicated to design

  • @wolf_hg
    @wolf_hg Год назад

    Mine seems to be having this issue now, have you had other symptoms when it chewed tapes? Mine seems to be having difficulty winding new tapes. Idler replaced and all. Could this wear somehow affect how the deck winds the tape in FF/REW?

    • @hifirulezzz
      @hifirulezzz  Год назад +1

      it has nothing to do with winding, check if you assembled brakes correctly when replacing the idler tire. In this video, I show how to fix chewing when clicking reverse mode.

  • @dimitarkirchevdimitrov6321
    @dimitarkirchevdimitrov6321 2 года назад

    Hi, what is the source for the gauge you're using in your videos?

    • @hifirulezzz
      @hifirulezzz  2 года назад

      eBay is the only source these days...

    • @dimitarkirchevdimitrov6321
      @dimitarkirchevdimitrov6321 2 года назад

      @@hifirulezzz Thanks for the reply! Any chance you can share the link?

    • @hifirulezzz
      @hifirulezzz  2 года назад +1

      @@dimitarkirchevdimitrov6321 Please check my other videos, I have shred a search on eBay two or three times over the last week only.

    • @dimitarkirchevdimitrov6321
      @dimitarkirchevdimitrov6321 2 года назад

      @@hifirulezzz Alright, thanks!

    • @hifirulezzz
      @hifirulezzz  2 года назад +1

      @@dimitarkirchevdimitrov6321 www.ebay.com/sch/i.html?_from=R40&_trksid=p2334524.m570.l1313&_nkw=cassette+head+alignment+gauge&_sacat=0&LH_TitleDesc=0&_odkw=gx-300+cassette+head+alignment+gauge&_osacat=0

  • @gixxerboy555
    @gixxerboy555 Год назад

    Those are the latest but also the baddest XL-II tapes ..,Maxell ever produced..the tape is less quality and also much thinner than the good old Maxell XL-II tapes..

    • @LapisandHamtarolover
      @LapisandHamtarolover 11 месяцев назад

      That's a bigger ouch for the tapes being this thin if something were to fail.

  • @tonymontana897
    @tonymontana897 Год назад

    You never even showed us "how to fix". That's the whole point of making a video, so we can actually see you fix it. Showing us clips after you have fixed it doesn't help.

    • @hifirulezzz
      @hifirulezzz  Год назад

      Thank you for your feedback and I understand where you're coming from. In the video, I made an effort to detail each step and highlight every screw that needed adjustment. Initially, I had to disassemble the head carriage and tape transport, make the necessary adjustments, and then reassemble everything. All these steps were conducted and tested to ensure the solution worked effectively.
      While I did not film the entire process in real-time which would take hours, I aimed to present a concise and efficient walkthrough, focusing on the critical adjustments required for the fix. The purpose was to provide you with a clear, concise, and practical guide rather than hours of footage which might be less helpful.
      I understand that you would have preferred a different approach, and your feedback is truly valuable to me. I am continually striving to improve and create content that is most beneficial to you and all our viewers. Thank you again for sharing your perspective, and I hope my future videos will better meet your expectations.