Refill Samsung ML2160 M2070 M2022 MLT-D101S MLT-D111 Remanufacturing Toner Cartridge
HTML-код
- Опубликовано: 15 сен 2024
- Remanufacturing instructions for Samsung toner cartridge ML-2160 ML-2165 ML-2165W SCX-3400 SCX-3400F SCX-3405 SCX-3405F SCX-3405FW SF-760 MLT-D101S
- Use the CC button to activate subtitles in your language! -
There are 2 type of cartridge: the starter cartridge, shipped with the machine, print 700 pages. Standard cartridge print 1,500 pages.
Compatible cartridges made in China may have some difference from original Samsung cartridges. First of all, instead of plastic rivets they have screws.
TOOLS
- Small flat screwdriver
- Phillips head screwdriver
- Needle nose pliers
- Knife
- Iron solder
- Toner vacuum or compressed air (better)
SUPPLIES
- Toner for use in MLT-D101S (55 gr.)
- Chip for use in MLT-D101S
- Drum (if the old drum is damaged)
- Isopropyl alcohol
REPETITIVE DEFECT CHART
OPC drum 62.83 mm
Primary charge roller 25.45 mm
Developer Roller 37.70 mm
For any question or suggestion leave a comment
--------------------------------------------
Link Accessori srl
Via Beverara 224/7
40131 BOLOGNA (Italy)
www.linkaccesso...
email: link.accessori@libero.it
other links:
www.emmegiricam...
www.samsung.com...
----------------------------------------------------------
Very nicely explained 👍
Thank You 🙏
The chip is a page counter, after a number of copies it will stop the printer, not important how much toner is left in the cartridge.
Petros, are you sure about the quality of the toner you've used? check the recovery blade, verify the side plates are in right position
I have cartridge MLT d111 that showing no print cartridge I have filled with 80 gm powder and 3-5 print has taken by this cartridge what i need to do for this.
What chip is sitting there on that small PCB? If it is just a serial EEPROM memory it should be possible to reprogram it without replacing it. I did that with SCX-4200 using Arduino as a programmer and it always worked (there was I2C or maybe SPI serial EEPROM inside the cartridge and the content could be easily found online).
It's not a normal EEPROM, samsung has become smarter. I think it's not possible, or it's so difficult that it's easier to buy a new compatible chip for some dollars
I have an MLT-D101s Cartridge which I got refilled for the first time recently. After refill, it isn't printing properly. It would not print one half of the page, sometimes completely light print and not dark enough. The results were brilliant for the genuine ink, but new refilled one is not satisfactory. Only once after the refill was done, the print of a page was really dark and good but afterwards it is worse.
Shown it in almost every shop and none of them are able to come with a solution. One person just today changed the ink saying it to be of a bad quality but his ink gave the same output. The Developer Roller is not completely black even after 5-6 print. What could be the problem?
Kindly tell me what could be the problem as the new cartridge cost a lot and it is not affordable.
change the ink does nothing.in case of cartridge that doesn't print half of page I think the problem is one of the side cover not in correct position, or some component (drum or developer roller or charge roller) in wrong position due to wrong position of one of the side covers
Sir I have refilling the new one cartridge mlt111 but it's one side printing is liner liner how to fix it sir pleases suggest me
I thing the side plates cond be not correctly installed. Try to disassemble and reassemble the cartridge
Hello, I just bought the M2022w and I have a few questions, 1) Does the cartridge come with the plug that was used to seal it (the one shown at 5:27) or was this cartridge customized before? I ask because I'm seeing people melting a hole through the reservoir, but I don't know if it's needed or if they're just being lazy and don't want to tear the whole thing apart. 2) Is it really necessary to replace the reset chip? User U Refill Toner clams to have refilled eleven times without replacing the chip ever (/watch?v=81bU-hJRz4k) and just ignoring the warning light.
the cartridge was not customized, it came with that plug. you can drill a hole through the reservoir but in this case you can't clean all the components of the cartridge. it's necessary to change the chip, but in some old driver version may be not
Is this refill method is useful for my Samsung Xpress M2070W toner Cartridge?
Yes
won't it work if we don't change that CHIP? You said we HAVE TO change it everytime. is it right? or just first time?
Nice video, i was wondering if there is a way to do this same install with a printer heat hole making tool. I have one of those and it would make it much faster
for screws what type of screws do you mean?
You can use a printer heat hole making tool, but in this case you can't clean the internal components: drum, charge roller and so on. print quality may be not perfect, expecially after some hundreds of prints.
not important the type of screws you use, better short screws
i do 60 a day with viandant5 method at work, the hole method is just not worth it, high print quality lose
HELP! I did the refill the way is is shown in this video, however the toner is leaking from the device. Could this harm the printer? That aside, it still shows that i have 0% cartidge left (even though i have a ML 2160 printer and used a toner compatible with it). For some reason, though, i printed some pictures, however they are full of vertical lines that have different amounts of toner, making them of pretty bad quality. I d appriciate any help.
it still show 0% cartridge left because you have to change the cartridge chip. for the other quality problem, verify if the developer roller is in its proper position, or if the mylar blade of the developer roller is damage. the cartridge should not leak toner.
viandant5 So the quality has to do with something not being in the right position, cant it be something else? Can you please be a bit more specific in what i should do? It just is that i suck with such staff and i worry i ll fuck something up.
Gnsd45 I can't be sure, but I think you have to disassemble again the cartridge. there should be something not in right position
viandant5 I see, thanks for the help.
hi thanks for the video you told that the chip is the page counter and we can use until it blink red, if we reset the page counter by settings ,still it is smart or ?
if in your printer there is the possibility to reset the page counter by settings it's not necessary to change the chip
viandant5
I cover the chip with a small cellophane tape. It works fine. Just one small compromise- it won't show me the percentage of ink anymore but the toner status blink will be gone.
Anup Satpathy
good, but never update the printer firmware
Mera Samsung m2021 printer hai wo blink Kar raha hai Kaise thik hoga
after refill d101 with chip changed.it prints left side ok but at middle and right side left faded print why?
+Prasanta Patra may be the side plates are in wrong position try disassemble the cartridge and riassemble it again
Its OK but at dev. Roller not properly black
+Prasanta Patra may be the developer roller blade is out of position, but I would check the side plate, it's easy they are in wrong position, the plastic tabs are a problem if not cut properly
This is almost the how to rebuild laser toner. Where can I properly dispose my old toner? Samsung collect and recycle this?
every country has its own regulamentation. for sure samsung don't recicle their old toner cartridges
you said change the chip means with new one ?
yes, with a new one
viandant5 can i reset it or program it..insteat of new one i think it is not easily available online
it's easier to change the chip. I don't know any reset program
Nice vidio
Please powder name
Every black Samsung toner powder will work
HMNN, a new I shall buy- much easier this is. Too short, life is!
I refilled my Samsung MLT-D101S and getting 5/6 horizontal lines from top to bottom of page. Also Slight grey patch on the left side from top to bottom. Please tell me how to correct it ? Please see the scan images
s21.postimg.org/4xf7b38nb/faulty_toner_2.jpg
s24.postimg.org/3u5qo01id/faulty_toner_1.jpg
jtuell57 I think the drum is damaged. the grey patch on the left side may be you have not dump out all the old toner
where do you buy the chip?
in several places using google search, ebay for example
viandant5 do you have to replace the chip every time you refill?
Acid Luva
you can use the old chip until it start to blink red, then, insert a new chip
I did it excactly the way you recomended to do it but it was not successful.
Here you can see the result: postimg.org/image/6ljhrxvjn/
I made many copies and all of them look like the copy in the link.
Do you know what might be wrong?