Kwikset door latch repair. Save your handle and save some money.
HTML-код
- Опубликовано: 29 сен 2024
- Kwikset latch repair. Save your handle and some money.
In this video I demonstrate how to replace the door latch mechanism in the kwikset door handle. For $8, you can keep your handle.
Install a new handle video: • Kwikset door handle/kn...
My Amazon page: www.amazon.com...
As an Amazon associate, I earn from qualifying purchases.
![DDG & G Herbo - Nosey [Official Video]](http://i.ytimg.com/vi/I9Ra0Zc2NlQ/mqdefault.jpg)
Did this today. New latch was $8.49 at my local Lowes. Great video, easy to follow. Thanks for posting!
Thank you for showing that the vertical screw plates can be pried apart. I was wondering how to get them apart.
Loved The Outtakes! And Of Course The Video!! Thank You!
Amazing tutorial sir! Thank you!
Thanks for the information, it's exactly what I needed to know. Very helpful
How do you get the latch out of the door when it will not retract?
How did you get the internal mechanism to turn when you took your door knob off? Mine broke and I can't open the door and I have both door knobs off and it won't budge.
Is it jammed?
@@jodaddysworkshop786 Our door is stuck closed. How did you get the latch out?
Allright! I feel like I conquered the world! It has been months since my pass-through garage door wasn't locking me in or out! I even bought a Cracker Barrel Friday fish fry lunch - which would have been CHEAP if it fixed the problem - for a man-friend to adjust it (I am a single 66-year old female, easily frustrated trying to figure out what was wrong and thought it was just a loose handle), but it still didn't work...then I found YOUR video, stopped it at the point where you flashed the Kwik-Set Exterior Entry Door Latch replacement parts so I could write it down, drove over to Lowe's and in just a half of one day (I admit to being a slow learner - Ha ha ha) it is working! Thank you! Thank you! Cindy from Phoenix, AZ
Awesome!
the part where the knobs / handle were put on toward the end, the knobs / handle were on the wrong side
Unfortunately the latch is jammed in the locked position and the door is closed. I have taken the door knob assemblies off, but don;t have a way to get the jammed bolt out, so I am stuck with a locked door.
Actually, this JUST happened to me yesterday. If you take like a sharp pointed thing, ( I used an old pocket knife) and pry it open, simultaneously keeping pressure on the door, and you can get it open. Hope this helps !
@@jtemme76 Hi, jtemme76,
I had tried that for a half an hour and it worked in the past. If you can get the bolt to slide just until the taper part, my last experience was this worked. After I posted this, I thought: I need a tool to cut the bolt. I bought an Oscillating Multi-Tool and a bald made for metal. It took longer to get by battery from storage in the basement, and change to the metal-cutting bald than the work itself. That bolt was cut in about a minute! The door opened easily and a screwdriver got the latch assembly out. I picked up a new one tonight, and I’ll have that door handle working as good as new tomorrow morning.
Now I have a new tool, and I’ve been wanting one of these for a while.
Thanks for the response I found no videos on this problem but since I saved the old latch maybe I’ll make one and post it.
Dude, THANK YOU! I was just getting ready to go drop a ton of money on a new latch style door knob to replace the one I have. Of course it had been sticking for awhile, and all the times I shoulder checked the door to get it opened cracked some of the wood on the frame, that might be another video you made need to do :) [repairing cracked door frames for dumbasses] oh well, live and learn. Thanks again! Going to go put to use the knowledge you just gave me.
How did you get the door open?
Thank you!
I am revisiting my issue again and remembered my issue. I have 70's interior doors with a 2 3/8" backset and no room for an adjustable backset. I have ordered a new doorknob set from Amazon for 12 bucks and guess I will need to run a 1" wood drill bit thru the backset opening to allow for the extra room needed for an adjustable one. If you know an easier way let me know.
Kwikset will send you a new latch for free, just call them. Lifetime warranty
The flange around my front door handle (inside) doesn't just pop off. The right side comes off... the left side is locked in place. How do I remove the flange?
Help! I did the same thing and I can’t get my door open. The latch is stuck in the catch. Any suggestions? I couldn’t even get the door off the hinges it’s too tight! Anybody??
A better video would have been repairing your old unit....what broke?????
He did show what broke. The latch is worn out because the metal is worn away. You can’t repair these. You have to fix them by replacing the latch. Take a look at the tumbler area on the old one he held up and the new one he held up. The old one all the metal is worn away. Common issue for heavy use front doors.
Excellent. I now locked out. lol, how did you remove that piece to open the door again? Thanks
If you could NOT get the latch to go back (like me), pop the hinges, quick and easy.
they have sizes how can i know the latch size of my door
Maybe if you have the model number of you assembly.
I cleaned and oiled my latch and lock set and it fixed this same issue for free. Might just get a new latch anyway for that price
I did this, but it still unlocks when I give it a hard turn to the left. Why would that be?
From inside or outside?
@@jodaddysworkshop786 from the outside.
2 thoughts, 1. would've been helpful for you to go ahead & do this on the door 2. it'd be nice to hear a brief comment on backset (?) lengths (your's look to be 5" but there are also 2 3/4' & 2 3/8" adjustable) - i say that as neither Lowes no Home Depot in my area seem to have the shorter backset latches - Amazon is my friend today I guess
If anyone is having the issue where their latch or deadbolt is loose or falling out due to the screws stripping out the inside of the door. I have invented a new door hardware that solves this problem. No more glue, sticks, puddy, or that ugly metal sleeve that ruins the look of your door. Great for DYI people like Jo Daddy, property maintenance, and you.
Lock smiths and plumbers charge a lot of money for things people can do on their own and save money. Thanks for showing things like this.
Kinda the point of their jobs. Do things people might not know how to do.
I thought you were going to show us how to fix that , not buy new, but its nice to know they sell them. Ill give you a B. ty
Great job is your wife tired of. I sure could use a nice gentlemen. I am stuck in house with this latch.
Too bad you didn't take apart the latch assembly - that would have been helpful.
I had the same issue with my door latch. I contacted Kaiser via email and they sent me a new latch free of cost. These latches have lifetime warranties. At least on my door handle.
Thanks JD! Just changed mine out today. Works as it should.
I was just typing about removing the old face plate when you added that to the end of the video.
Great video on a replacing the door latch most people never even think about just replacing the latch only.
Keep up the great videos.
How do you even get the door open in order to replace the mechanism, though.
thanks! worked like a charm
Thank u. Gonna try. Bought whole new replacement set and latch will not catch. But I did not use that other piece to crimp to latch. Maybe that’s the problem.
Thank you for the tip on how to get the end pieces apart. I can now buy the cheaper replacement part (without the plates). :)
Thank you! I just took apart an enry handleset that doesn't fully throw the latch when turned in one direction and diagnosed the problem as a worn latch. I could see that the latch hole was worn quite a bit on one side (top) but not the other (bottom). This explains why the door handle worked when turned in one direction but not the other. I appreciate you holding up the package in the video so I know just what to look for when I go to the store. Thanks again.
Where did you buy sir?
Lowe’s
Thanks for the video. Going to replace mine today.
F*cking Thank You! Thank You! Thank You!!!!!!!!!
Do you know if there is a way to change the length of the plunger that comes out of the latch? Mine is long and it hits the trim so I need to get it a little shorter if that's possible...
I think there may be a sort of switch inside. Maybe mot on this model, but I've seen it on others.
Same problem. But mine is the kwikset smart lock. Although the smart lock works on the deadbolt, but my latch is stuck. I got to all but the replacement. Will any kwikset tubular replacement work on my latch?
Not sure.
My issue is that I installed a new Kwik Set knob and latch set and now the lock is hard to turn and will not loct with either a key or the button or the interior button?
Sometimes you may need to loosen the screws and wiggle everything a little bit. See if that helps then tighten back up.
thank you! exactly what I was looking for
The round piece is not an adapter. It is usually used on a metal door, but can also be used on a wood door where just the hole is drilled and the flat plates are not used.
Great video! I’m a 26 yr old and looking for tips to start fixing up my home the most cost effective way! This video was helpful and informative and REALLY simply by your explanation! Keep up the great job!
How do you get the latch out if the door wont open? Just unscrew the door knob?
That, or pull the pins from the hinges.
Well I do have question most of the videos they accuse the strike plate as the main culprit when it comes to issue of latch not catching the strike plate . But how often do you think latch might be the one which needs replacement
Wish I had a good answer for that.
Any tips on how to get the latch out if it's locking you out as described in this video? Is it just a matter of taking the handles off and getting in there with some needle nose pliers to actuate the latch?
I have the same problem - did you figure it out?
@@jaytyler3076 Yep, I used a flat, sturdy piece of metal I found lying around (I think it was the clip from a garage door opener remote) and a skinny screwdriver to push the latch mechanism open. Had to shove them between the door and the door frame to get at it. There was much cursing involved but eventually I got it open. I found a video of a locksmith fixing this same type of latch and it took him like 10 minutes to do the same thing, so that was my inspiration.
With access on the inside handle you can take off the handleset. Using a screwdriver, or pretty much anything, you can open the latch further than the door handle will.
Replacing the whole latch is the easiest and most certain solution.
The latch shown in this video is known as a 'deadlatch', or casually as an entry latch. It has a slider that prevents the door from being carded. It's usually used on entry handles with locksets.
The other type is a common/interior/passage latch. It doesn't have a slider, although better ones have an anti-friction pad that might be confused at first glance. They are used on entry doors with a separate deadbolt. You can substitute a deadlatch but the trim plate profile is different.
In a pinch it's possible to disassemble and lubricate the Kwikset/Baldwin latches. To do this you'll need access to the inside by separating the latch into two sections. Inspect the mechanism that sets the door offset. There is a roll pin that pushes down on two black plastic sliders. Those sliders are guided by slots on either side of the tube. Push out the roll pin that sets the offset and use a small flat screwdriver to push down the plastic sliders as the roll pin did. The two sections will separate. You can now reach the sides to lubricate. Reassembly is just lining up the parts and pushing in the roll pin.
Use a *tiny* dab of clear waterproof grease. People unknowingly rub against the latches. No one wants mystery grease stains on their clothing.
To fully disassemble the latch tube you can drive out the rivet. If you have to go this far it's probably because the parts are worn beyond use. It's a bit fiddly to put back together.
Finally that sleeve isn't for worn out doors. It's for so-called "trailer door" installations where the latch is retained by a press fit.
Thank you!!!!!!!!
JoDaddy if I still can't fix my door knob and trigger then consider me an idiot because that was very self explanatory like, I had it broken for two months, you'd think this guy is hopeless, as I probably would judge someone as that esp if I end up successfully fixing my door knob and dead bolt as the brand quikset is a common household essential so instead of having someone do this for me I will take a crack at it, because of your inspirational video, Gary and Brandy in Kaneohe
Question: how were you able to get the door open if the latch wouldn’t retract? That’s what I’m trying to figure out. I don’t mind replacing the latch, but I need to get the door open in order to do that.
I had access to both sides.
We also can't open the door because the latch is malfunctioning with the door closed. Did you ever find out how to get the door open so we can replace the latch?
Thank you for your video. You saved me time & money and I appreciate it. Good karma is coming back to you💫
The other part for metal or wood door
Great video, my schlage lockset the catch bar would not go in, will see if I can find just at center
Show Me how you removed door knobs--I see no screws to loosen on mine, just like yours.
Just got it done 😁👍🏽
Thanks JD! I changed mine today.
Thank you! Nice video. I'm going to Lowes to buy one today.
Thanks Jo! You just saved me $150. Did it myself.
Another simple fix, but the one I needed! Thanks, I thought I would have needed a new handle but as you identified there is a kit for that.
Very nice
Kwikset locks come with a lifetime warranty.
Indeed, I was doing some routine maintenance on an older Kwikset, when a piece fell out I didn’t recognize. The handle when back together just fine, and still worked, minus that piece. So I email Kwikset and ask if they can help identify it…. They sent me a whole new handle set and I didn’t even ask for it. I’ve held onto it for the past few months. Then the other day, what happened in this video happened to me, and lo and behold I had a brand new one standing by. Thanks Kwikset!
The warranty on their website says you have to provide proof of original purchase to make a claim. Did they ask for any of that when you emailed them?
@@JonathanLarson-CoolJon Nope, they just asked me to take a picture of the handle, which I did, and along came a new one.
thanks for the help, just the help that I needed!
Thank you sir, you saved me few $$$.
Thank You! Made it so I could figure out the problem and fix it myself. Saved me so much headache and hassle.
Thank you so much. Exactly the same problem I have, and now I know for sure how to deal with it
Thanks for this video. You just saved me a lot of money and hopefully I will be able to use the front door again very soon.
Excellent, off to the store!
Thanks for the new angle of attack!.
Very smooth and knowledgeable!!
What about the thumb type door latches where the spring has worn
No experience with those, sorry.
In most cases, it is the same latch assembly that is used with the deadbolt. You can either find a latch of the same brand, or replace the deadbolt.
@@davidcox9983 In my case, and most I've seen, actually, the thumb latch is a few inches below the deadbolt.
I temporarily replaced it with a standard doorknob from a spare bedroom until I get the latch fixed. I have no idea of the brand, I'd be open to any ideas how to ID it, since there's no name inscribed anywhere i could see.
@@stellijer My mistake. I think you are talking about a handleset with a thumb press latch release rather than a deadbolt. The latch assembly is usually still the same as as the latch used with a regular knob assembly. Often you can identify it by looking at the plate on the edge of the door. If you still can't identify it, you can do a google search of latches, and look at the image to see if you can identify it. Does the latch have a square hole, a plus shaped slot, or a minus shaped slot for the tailpiece?
Thanks for the tip. I replaced the door latch for $8 and now all works wonderfully. Keep the videos coming!
Thanks for the video and the easy fix. Excellently done!
hi barry grate show 👍👍👍👍😄
How am I supposed to take off the doorknob if the door won’t open!!
The first 2 minutes helped me out
Thank you
you only save like 5 bucks. it's 15 bucks for new door knob. But if you wanna save like 5 bucks then yeah. LOLs. Might as well get the whole thing.
Unless they want to keep a knob based on a design that may not be available anymore.
Did you just make this video without showing how you got the damn assembly out of the door ? It's in there & won't move. Thanks for the laugh.
Maybe this video will help: ruclips.net/video/bsgpomUQcy0/видео.html