Dalam video ni, steam iron ni ada masaalah pada vibration pump.. kerosakan vibration pump boleh diketahui dengan mendengar bunyi ketukan vibration pump sangat kasar.
in this case, either the valve is damaged or the power board is damaged. if you have a multimeter, you can check the input voltage to the valve. if there is a voltage current entering the valve without pressing the Steam trigger this means the power board is damaged. and if the steam comes out but there is no voltage current into the valve.. this means that the valve itself is damaged, possibly the passage is stuck in the valve cover causing the passage to always be open.
@@didottukangelektronik1334 Thank you very much. Thanks for your reply... I measured with a multimeter. valve no problem. The valve is also intact. When I press on/off, the valve operates directly. opens the valve. Electricity is coming to the valve. What could be burned on the motherboard?
salam tuan. nak tanya pump x berfungsi. dah ganti pump baru dan dah cek thermostat bacaan 198 ohm. dah masuk air dlm boiler wap keluar sampai habis pump tetap x jalan. apa ya mslh dia
Salam, iron saya model ini, apabil d on, trip karan di rmh, sdh cek diapunya solenoid valve, bacaan ok, cek kabel, ok juga x ada bersentuhan, ttapi bodi relay yg bwarna hitam, ada longgar bukan pada kaki yg ada solder, mohon pencerahn drp cikgu, apakh yg mnyebabkan trip....tk..wasalam
Cuba suruh kawan abg periksa L/N + bumi boiler, soleplate dan valve.. periksa juga wire pada hose cord ada kesan² luka atau tidak? 4 perkara ni boleh jadi penyebab trip dB.. Earth/bumi tak boleh ada rintangan dengan L/N..
Hello, pls help, i have a big problem with gc9630, dont Want to hot and all three leds its blinking intermitantly, single led blue in iron hand dont light. I change the PCB everiting k But it work five minute and then its back Again with my big problem, all three leds light intermitently and dont Wont to hot, everiting îs cold. Sorry FOR my english, pls help with a idea
hi how are you, the three lights are flashing (eco + power + easy Declac) this means the electronic main board is not getting the thermister sensor signal. please check.. 1. Thermoster sensor under the boiler and on the soleplate 2. The circuit connection on the power button between the three pins has broken. 3. there is a problem with the wire on the hose cord. Google translate 😊
Salam. Lepas tukar pam dan guna dlm masa 2 bulan, ada lebihan air keluar semasa guna iron. Stim masih ok tapi tak sekuat biasa. Saya pakai model GC 9642. Apa masaalah agaknya?
Kes mcm ni ada 2 kemungkinan.. 1. Soleplate tak cukup panas.. 2. Sistem boiler.. Boleh cuba trik ni.. Cuba kosongkan air dalam boiler... Dan isikan dengan air sejuk dan biarkan beberapa minit. Lepas tu buang air tersebut dan uji seperti biasa..
Soleplate panas cukup dan boiler working mcm biasa. Saya test semula iron, stim/air tak keluar drpd lubang di soleplate. Keluar dr tepi body iron. Saya perhati lubang2 soleplate mcm kotor. Ada cara repair lain?
Can you measure the terminal of the water pump to know if it is ok?bcoz the terminals are open in my case
there is a mega ohm reading on the pump.. the mega ohm reading is different depending on the pump model..
Salam tuan lpas tukar PUM kenapa wap keluar sedikit ye.mula2 je keluar lpas tu xdey terus
Waalaikumussalam.. kena pastikan masalah sebenar yg dialami pada steam iron abg..
Dalam video ni, steam iron ni ada masaalah pada vibration pump.. kerosakan vibration pump boleh diketahui dengan mendengar bunyi ketukan vibration pump sangat kasar.
Terima kasih bang didot.
When the Tefal boiler iron is turned on, the valve remains open. what is the solution?
in this case, either the valve is damaged or the power board is damaged. if you have a multimeter, you can check the input voltage to the valve. if there is a voltage current entering the valve without pressing the Steam trigger this means the power board is damaged. and if the steam comes out but there is no voltage current into the valve.. this means that the valve itself is damaged, possibly the passage is stuck in the valve cover causing the passage to always be open.
@@didottukangelektronik1334 Thank you very much. Thanks for your reply... I measured with a multimeter. valve no problem. The valve is also intact. When I press on/off, the valve operates directly. opens the valve. Electricity is coming to the valve. What could be burned on the motherboard?
@@didottukangelektronik1334 tanks
salam tuan. nak tanya pump x berfungsi. dah ganti pump baru dan dah cek thermostat bacaan 198 ohm. dah masuk air dlm boiler wap keluar sampai habis pump tetap x jalan. apa ya mslh dia
Waalaikumussalam.. jika model yg sama dengan video.. periksa balik sambungan pam tersebut..
uihhh sayang kat belakang yang tak tahan tu. Boleh stop repair terus
Don gibab.. Naver gibidap
Salam, iron saya model ini, apabil d on, trip karan di rmh, sdh cek diapunya solenoid valve, bacaan ok, cek kabel, ok juga x ada bersentuhan, ttapi bodi relay yg bwarna hitam, ada longgar bukan pada kaki yg ada solder, mohon pencerahn drp cikgu, apakh yg mnyebabkan trip....tk..wasalam
Waalaikumussalam.. di valve tu dah cuba test bacaan kaki connection L/N ke bumi ada bacaan tak?
Lagi satu saya bukan cikgu bang✌️
Maaf encik..ha...ha..., Kwn sya dh cek L/N x ada short kata dia..
Cuba suruh kawan abg periksa L/N + bumi boiler, soleplate dan valve.. periksa juga wire pada hose cord ada kesan² luka atau tidak? 4 perkara ni boleh jadi penyebab trip dB..
Earth/bumi tak boleh ada rintangan dengan L/N..
Tk atas pencerahan ini..
Hello, pls help, i have a big problem with gc9630, dont Want to hot and all three leds its blinking intermitantly, single led blue in iron hand dont light. I change the PCB everiting k But it work five minute and then its back Again with my big problem, all three leds light intermitently and dont Wont to hot, everiting îs cold.
Sorry FOR my english, pls help with a idea
hi how are you, the three lights are flashing (eco + power + easy Declac) this means the electronic main board is not getting the thermister sensor signal. please check..
1. Thermoster sensor under the boiler and on the soleplate
2. The circuit connection on the power button between the three pins has broken.
3. there is a problem with the wire on the hose cord.
Google translate 😊
Salam. Lepas tukar pam dan guna dlm masa 2 bulan, ada lebihan air keluar semasa guna iron. Stim masih ok tapi tak sekuat biasa. Saya pakai model GC 9642. Apa masaalah agaknya?
Kes mcm ni ada 2 kemungkinan..
1. Soleplate tak cukup panas..
2. Sistem boiler..
Boleh cuba trik ni.. Cuba kosongkan air dalam boiler... Dan isikan dengan air sejuk dan biarkan beberapa minit. Lepas tu buang air tersebut dan uji seperti biasa..
Soleplate panas cukup dan boiler working mcm biasa. Saya test semula iron, stim/air tak keluar drpd lubang di soleplate. Keluar dr tepi body iron. Saya perhati lubang2 soleplate mcm kotor. Ada cara repair lain?
Multimer jenis apa tue bang
Klau kepala plug cair dkt kaki live/neutral apa problem eh bos?
Assalamualaikum bang.. Periksa soket plug dahulu.. Jika ade wire tak ikat kemas boleh menghasilkan sprak dan haba..
@@didottukangelektronik1334 waalaikumsalam. Plug lama saya dh gnti baru. Plug baru pon still cair melekat dekat extension wire.
Connection wire kena ikat kemas.. Cuba guna plug top dan soket point gred bagus mcm jenama MK.