Nice floor pans. Your pretty good at this. Almost 5,000 subs. You should have a lot more before its over with. I love old hot rod channels like this. Iron trap Garage, This old hot rod, Bad chad, and Half Ass kustums, there are so many old ford guys. So many good channels to watch.
Excellent work on the floors! 90% of building a car is cleaning, grinding, scraping and sanding...it's always a treat when someone else has done that part.
Big fan! Noted on your 3W corners, you mentioned fabbing them. Dont quote me on the source, but I bought corners a few years back from Brookville ( I think!🤨)
Thanks for sharing, Travis! 'Beautiful job on the floor panels! Watching you work with rust-free metal was entertaining, but seeing how you work with rusty panels is truly educational! Respect! Enjoy! Be safe!
Travis one FYI when you’re putting both those panels together to weld them should put weld proof primer on both sides before you put it together you’re putting bare steel the bare steel I know they probably won’t rust in your lifetime but but well true primer would be the way to go I overthink things did a great job on the floor I was really impressed junkman do
Just my .02 but weld thru primer is akin to snake oil. When I worked in a collision shop I'd occasionally fix cars that had been previously repaired and the seams where weld through primer had been used were all rusting after only a couple years. The zinc stuff holds up a little better than the copper, but it's still not all it's cracked up to be. The best protection is seam sealer, epoxy primer and wax oil in all the crevices after paint. As long as the seam isn't exposed to moisture it won't rust, I've cut apart cars that had been sitting in a field 70 years and even though the entire body was covered in surface rust the seams still had clean bare metal. Anyway that's my rant on weld through primer.
Just found your channel LOVE IT....... Keep it up. I'm learning something every time I watch it . Can't wait till the next video. P.S. Love the way you involve your boy/shop mate....
Just found you on U-Tube and added you to Proshaper, Make it Kustom and Fitzees Fabrications. So ur in good company 😅. Hope my Morris Minor Traveller floors end up looking like yours (no Pulmax unfortunately 😮💨. Love your workmanship and your "I'll figure it out" attitude. Thanks 👍
Great job! It looks to me like you could really use a roper Whitney Jr. hand punch. You'll get nice crisp holes and not have to deburr...fast too. Love your channel. Especially the Pullmax stuff. I bought a Pullmax 3 years ago but due to moving and a new shop build have not gotten the chance to play with it yet..
You and I agreed a long time ago that I’d never brag on you, in fear of giving you the “big head”….BUT….”IGOTTASAY”, that turned out real nice!!! That’s the exact way I would have done it….”IFICOULDADUNNIT”!!! 👍🤔😁⚒
The bitchin floor pans are much thicker than stock and since I don’t know where the seat is going to be mounted I didn’t make any braces. I don’t believe that kit comes with floor braces anyway. I’ll make sure to remind kris to tell the next owner about the braces.
Nice clean work, your a very talented young man. Just a suggestion, you need to slow your videos down when you come to bending and folding,( say your corners) so that your audience will understand your drawings on paper and how they are applied to sheetmetal. Thanks for sharing keep up the great work!
Travis, you do some mighty fine work!! I have a question, after bead rolling a panel, how do you stop "oil canning"? Should the panel have been stress relieved on the English Wheel?
Yes you should always pre stretch beads on an English wheel or a planishing hammer or even a hammer and dolly. So you don’t have to fix it afterwards. As you saw I did my pre stretching on my English wheel. Hope that helps!
That's some nice work you did, but I'm definitely not a fan of over lapping panel. No matter how well you seal them moisture will eventually get in between the panels and rust them out.
Mrs Richards: "I paid for a room with a view !" Basil: (pointing to the lovely view) "That is Torquay, Madam." Mrs Richards: "It's not good enough!" Basil: "May I ask what you were expecting to see out of a Torquay hotel bedroom window? Sydney Opera House, perhaps? the Hanging Gardens of Babylon? Herds of wildebeest sweeping majestically past?..." Mrs Richards: "Don't be silly! I expect to be able to see the sea!" Basil: "You can see the sea, it's over there between the land and the sky." Mrs Richards: "I'm not satisfied. But I shall stay. But I expect a reduction." Basil: "Why?! Because Krakatoa's not erupting at the moment?
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
Nice floor pans. Your pretty good at this. Almost 5,000 subs. You should have a lot more before its over with. I love old hot rod channels like this. Iron trap Garage, This old hot rod, Bad chad, and Half Ass kustums, there are so many old ford guys. So many good channels to watch.
Excellent work on the floors! 90% of building a car is cleaning, grinding, scraping and sanding...it's always a treat when someone else has done that part.
yeah this was sooooo easy compared to every other job lol
Big fan! Noted on your 3W corners, you mentioned fabbing them. Dont quote me on the source, but I bought corners a few years back from Brookville ( I think!🤨)
Looks great man! Well done
Boy, it's a joy to watch you do all the work. I wish I would have watched your videos before I did floors in my 39 Pontiac.
Excellent video Very nice Job on the floors I’m glad you are saving that 37 Sedan delivery Can’t wait for next week
Fantastic fabrication. That was a treat to see you in action. Great job! He should be pretty satisfied with that finished product.
I think so too!
Beautiful floor job . Love the intro.
Thanks for sharing, Travis! 'Beautiful job on the floor panels! Watching you work with rust-free metal was entertaining, but seeing how you work with rusty panels is truly educational! Respect! Enjoy! Be safe!
Glad you enjoyed it!
I got one of them saws damn I don't know what I did without it! Floor looks killer keep killing it you do good work!
Great job on the floors! Back to the dirty work 😂
Yup haha 😂 it’s really not that bad
Supurb job... looks factory....like the intro too...
New intro was mint! As well as the floors. 👍
Appreciate it!
Great work. As always!
I appreciate that
Beautiful work!
That new intro is awesome and perfect for your channel. ✌😁
I think so! The music will be different than this video because of the goof but very similar
Winner job accomplished fast an efficient
Thank you!
Travis one FYI when you’re putting both those panels together to weld them should put weld proof primer on both sides before you put it together you’re putting bare steel the bare steel I know they probably won’t rust in your lifetime but but well true primer would be the way to go I overthink things did a great job on the floor I was really impressed junkman do
Just my .02 but weld thru primer is akin to snake oil. When I worked in a collision shop I'd occasionally fix cars that had been previously repaired and the seams where weld through primer had been used were all rusting after only a couple years. The zinc stuff holds up a little better than the copper, but it's still not all it's cracked up to be. The best protection is seam sealer, epoxy primer and wax oil in all the crevices after paint. As long as the seam isn't exposed to moisture it won't rust, I've cut apart cars that had been sitting in a field 70 years and even though the entire body was covered in surface rust the seams still had clean bare metal. Anyway that's my rant on weld through primer.
I agree. great way to articulate it. i couldnt lol
Nice job 👍🏼 take it easy mate 👍🏼😎🍺🇳🇿
Beautiful work.
Thank you very much!
Very nice young man!
Thanks Chris! But I’m getting more toward old every day!
Great new intro, very professional. I watch a lot of you tin knockers you an artist sweat job.
Thanks that means a lot!
Great intro
Great work dude!
Thank you brother!
Like the new intro and also liked the overhead view on the pullmax
thanks, i wish i kept the film running!
Great👍
You do awesome work man! Love the pullmax I want one. 14:15 you need a roper whitney hand punch
awesome jop.
So cool... love the channel
Just found your channel
LOVE IT.......
Keep it up. I'm learning something every time I watch it .
Can't wait till the next video.
P.S.
Love the way you involve your boy/shop mate....
Thanks! That means a lot! Glad to have you here
You are an excellent craftsman...great job
Thank you John I’m trying
Just found you on U-Tube and added you to Proshaper, Make it Kustom and Fitzees Fabrications. So ur in good company 😅. Hope my Morris Minor Traveller floors end up looking like yours (no Pulmax unfortunately 😮💨. Love your workmanship and your "I'll figure it out" attitude. Thanks 👍
thanks peter!
On that intro steeze!! My man
love ya dog!
@@RACGARAGE ❤️ next time you thank a random Jeremy at the end of a video, make sure its me only 😆
Amazing work. Wait till you see the T. Rus’T’y 😅😂
Can't wait!
Great job! It looks to me like you could really use a roper Whitney Jr. hand punch. You'll get nice crisp holes and not have to deburr...fast too. Love your channel. Especially the Pullmax stuff. I bought a Pullmax 3 years ago but due to moving and a new shop build have not gotten the chance to play with it yet..
ive been eyeing one of those for a few years but havent pulled the trigger for what reason i have no idea
Travis, perfect job, you made it look easy.
I try!
I really thought the intro was great and you did an amazing job on the floors of the cabriolet as usual Travis
You and I agreed a long time ago that I’d never brag on you, in fear of giving you the “big head”….BUT….”IGOTTASAY”, that turned out real nice!!! That’s the exact way I would have done it….”IFICOULDADUNNIT”!!! 👍🤔😁⚒
hahaha thanks brother! heads still small though!
Sweet nice work love the tools you have Still building hand tools to work with here maybe a bead roller soon but until then I have freinds
hand tools always get the job done!
Very impressive! This turned out nice. I'd love to hear more about your background and where you picked up your skills! Keep up the excellent work 👏
Maybe someday I’ll do a video about myself but I doubt there’s that much interest about that 😂
You made the floors but what about floor braces to support the floor with mounts and bolts
The bitchin floor pans are much thicker than stock and since I don’t know where the seat is going to be mounted I didn’t make any braces. I don’t believe that kit comes with floor braces anyway. I’ll make sure to remind kris to tell the next owner about the braces.
Nice clean work, your a very talented young man. Just a suggestion, you need to slow your videos down when you come to bending and folding,( say your corners) so that your audience will understand your drawings on paper and how they are applied to sheetmetal.
Thanks for sharing keep up the great work!
I didn’t get much footage of me making that piece because honestly I didn’t think it was going to work
Are you OK you seam down and I'm worried about you. The content is great and I enjoy both shows😊
👍🏻
Travis, you do some mighty fine work!! I have a question, after bead rolling a panel, how do you stop "oil canning"? Should the panel have been stress relieved on the English Wheel?
Yes you should always pre stretch beads on an English wheel or a planishing hammer or even a hammer and dolly. So you don’t have to fix it afterwards. As you saw I did my pre stretching on my English wheel. Hope that helps!
Hey bro new to your channel I like what I've watched so I'll be turning in.
thanks alot man!
@@RACGARAGE your welcome mate
Hi been watching your videos
You do a job, I’m curious as to what is your labor rate
85 an hour
Since you do so much body work it would be great to have a spare bottle so you don't run out of gas. Enjoy
i really should
That's some nice work you did, but I'm definitely not a fan of over lapping panel. No matter how well you seal them moisture will eventually get in between the panels and rust them out.
Yeah overlapping isn’t my favorite either but sometimes it’s useful
Besides, the factory overlapped areas and this won't rust away in any of our lifetime
Mrs Richards: "I paid for a room with a view !"
Basil: (pointing to the lovely view) "That is Torquay, Madam."
Mrs Richards: "It's not good enough!"
Basil: "May I ask what you were expecting to see out of a Torquay hotel bedroom window? Sydney Opera House, perhaps? the Hanging Gardens of Babylon? Herds of wildebeest sweeping majestically past?..."
Mrs Richards: "Don't be silly! I expect to be able to see the sea!"
Basil: "You can see the sea, it's over there between the land and the sky."
Mrs Richards: "I'm not satisfied. But I shall stay. But I expect a reduction."
Basil: "Why?! Because Krakatoa's not erupting at the moment?