2002 Jaguar X-Type - Water Pump Replacement
HTML-код
- Опубликовано: 8 сен 2024
- An overview of the process to replace the water pump on a Jaguar X-Type.
Parts Installed:
- ACDELCO 252467 (252-467) Water Pump
- BANDO MFG. 3PK590 Belt
Torque Settings:
- Water Pump - 10 Nm.
- Water Pump Pully - 11 Nm.
Thanks for taking the trouble to explain things. I would be stuck without them. Garages in France don’t want to know about Jags and the dealer is not much help. The oil change info is great.
Glad the video was helpful!
Perfectly explained ❤
Great video thank you found it very useful I thought it was going to be a lot harder I will now change mind no need for trip to the mechanics keep up with the videos much appreciated
Great video. Thanks for your precious work!
Thanks for watching!
thanks for the videoman, im about to replace my jags water pump
Good luck with your replacement!
That is a very well done and informative video. Thank you very much.
Glad you found it useful!
lifesaver, bout to replace water pump too.
Thank you it was very helpful I just bought a 2006 x type and the water pump was on of my issue your video was very helpful thank you
Thanks for watching my video. Glad it helps and enjoy your X-Type!
[thank, you so much for you're helpful video.] 👍
thank, you so much.
Thanks mate very informative and helpful.
Good shit bro!
Some say that you should use a bit of some kind of RTV on the paper sealing gasket.
I've seen it done both ways. Probably doesn't hurt if done properly. Looking at the procedure direct from the Jaguar Workshop Manual, all it says is "install a new gasket".
@@TofuRobots Thank you for the answer. I saw this in the manual, too. Anyways, maybe I'll go the route with some RTV.
Thank you sir
You're welcome and thanks for watching. Be sure to also consider the tips other viewers have shared and good luck with your repair!
Similar issue on my 2003 X type with the 2.5. Only has 54,500 miles. Going through about a gallon of coolant almost every 2 weeks. I have traced drips right under the radiator under the Jag. Have not checked thermostat housing or thermostat.
Da li moze sa drugog jaguara stojergeret da se stavi na drugi i da radi? Ili se mora ponovo programirati
It’s a joy to watch the steps. Did u install the serpentine belt? I know it’s a wrestle when I did mine during replacing the alternator.
The serpentine belt was a major royal pain when I did it. The new belt kept on springing out of place, and I could barely get the tensioner compressed enough to give me the extra space for the belt to slide over it. Somehow I did it though.
It seems mine is leaking from somewhere behind the water pump. Is there a separate housing of some sort that the water pump is attatched to..?
THANKS FOR THE HELPFULL VIDEO. I HAVE THE SAME PROBLEM IN MY 2.5 PETROL X-TYPE. IS THIS PROBLEM GIVING YOU ALSO A SMELLING LIKE SOMETHINK IS BURNING? THANKS A LOT.
Burning coolant has a sweet smell. I've had that issue since the car was young. I could never find a definitive source however. When I find a leak, I replace the parts. At a minimum replace whatever you think is causing the issue if it doesn't cost too much. My x-type is now over 17 years old, so really every hose and seal should be considered for replacement.
Hey that burn might be your water pump starting to seize up. Upon pre seizing the belt will still run however start burning.
Hello, I have a bad leak on my 2006 type s he replaced the water pump and I wanted to drive it, let it warm up first and pulled it out of the shop at idle speed and it beeped the whole time. I parked out front he came out and said it was also running hot. My fans stayed on for a few min after turning the car off. We're thinking it could be a hose now ?? Plzzzz help $$$$
Would you happen to know the part number of the tension pulley?
is the tensioner pulley supposed to spin on use mine doesnt
When the belt is removed, the tensioner pulley should be free spinning to allow the engine cog to spin the water pump under tension. If the pulley doesn't spin freely or is locked, it could eventually damage the belt.
@@TofuRobots Thank you so much I am sure its not to difficult to replace.
i have a noise coming from that side of the motor ....not sure if its the water pump or that bearing next to it that has that bigger pulley
Maybe try disconnecting the belt from the water pump to see if the noise stops. Of course don't run it too long this way to prevent over heating.
I think you should have used a thin layer of silicone on both sides of the gasket
Yeah the extra insurance could save another gasket leak. But at least the procedure is very simple to do.
What engine 2.5 or 3.0?
Thanks for asking. It's a 3.0. But I don't think there is any differences in parts or procedures for the 2.5 water pump replacement.
@@TofuRobots thanks!!
mines leaks coolant from somewhere, not pipes or radiator
I also had to replace my reservoir expansion tank and lower expansion tank hose C2S23485 in the last few years , but both were visibly leaking.
no silicone ?
Some folks do, some folks don't. If you do, just be sure to use a very thin layer. If you don't be sure the surfaces are totally cleaned off.
Nece ni da upali. Sve jr provjereno ništa ne reaguje.
Is there a separate housing that goes with the water pump?