Thank you for a very competent high-quality video, I am far from a non-professional in welding, and my daughter became interested in arc welding, she is embarrassed by her hobby and trying not to miss your videos, she will master the ceiling. Thank you for your help, waiting for your new video 👍👍👍👍👍🖐️
The good news IS that a lot of spare parts are generic so you can buy them on others markets. Standart key hole wheels (OD 30mm, ID10mm, width 10mm), mb15 torch parts...
Hi, This is the same machine I got for Christmas! I'm new to the various welding techniques, except stick. The manual leaves a lot to be desired! What is the capped mig output used for? Any info you can give me I would be greatly appreciated. Thanks and keep up the great videos!
capped output is for spool gun. the four pins, 2 for spool gun motor and 2 for trigger switch. if you buy the hitbox spool gun, it has the right connector. i am trying to figure out which pins for the switch, so i can use those two pins for tig switch; probably need to remove the cover and see the wirings. the manual is very basic, and no schematic.
Hello, I use this welding machine since 4 months now and I would like to give you m'y experience. Like always with afordables chinese tools, the accessories are poor quality (gas tube, hammer). The graphite wire feeding is well made. There IS 3 wheels wire feeding (0.6 to 0.8 and 0.8 to 1mm Vshaped for steel wire and a 1 to 1.2 mm Ushaped wheel for aluminium). You need to buy Kshaped wheels to experience a better flux core steel welding. Functions : - TIG lift is usable but without a gas electrovalve regulation or high frequency starter, its not very usable for stainless steel or wathever. - MIG MAG IS quite good with synergic mode or manual mode. The welding IS great even if there are some parameters you need to adjust according to your welding position. The wire roller system with only 2 rollers does well with 1kg and 5kg wires. BUT you need to clear thé system often to keep it safe. - no complains with MMA, good penetration, arc stability and take off with rutiles sticks (basics sticks require a larger U0 than thé machine has but it works nowadays). Spare parts are lacking on hitboxweld website distribution (for example, there's no wheels, no gas diffusor and no parts replacement for thé machine). To conclude, I think this IS a good welder if you compare welding quality and cheap cost and if the welder keeps working after Time pass. I dont think it will last 20 years like my old SAF fro AC MMA welder but today inverters have a lot more electronic parts so its natural they suffer more. I own another hitbox welder, a 200A pulse TIG with HF which last since 2 years (approximatively 200 hours welding) and works well on stainless steel even if arc stability under 30A IS worse than an esab, Miller or lincoln professionnal TIG.
My example works well with MIG-MAG for cobalt steel and I have also tested it with FLUX core which was ok but I don't like FLUX as it pops and smokes. I have not tested aluminum as it requires too much fixing. In contrast, the TIG LIFT system is totally useless. I have been chatting with Hitbox for 2 weeks and they are completely clueless about how a weld works. They send a video that shows how to handle/set up the welding for LIFT. Totally worthless, they have to dab the tungsten electrode (which is blunt!) a lot of times before they ignite. They increase the Amp setting to get the welder's recommendation to over 130 Amps
You are mistaken as most of users of this welding machine or it's previous version HBM2280. Welding with fluxcore self-shielding wire (FCAW mode) needs to be done on straight polarity i.e. "-" on torch and "+" on detail. Incorrect polarity is the main cause of severe slagging and spattering of metal. You may reconnect the cable on the front panel and redo the test. You'll see the much better result!
A professional video from someone who obviously does lots of welding, as a beginner what would make this video even better would be some explanation either as a voiceover or some pop up text to explain what and why you are doing it. Many thanks.
Hi make and test. I bought one of this hitbox SYN mig 200 pro welder. Mine's did not come with the tig torch, so I order one but the input end is too small for the connection port. I don't know where you get yours. I'm asking if you can provide me a link for one. Or where can I get it. Can I also get the dimension and the measurement for it and a code number if it has any?.
Hi again, Another question. What tig torch should I get for this machine? Thanks again! Also, can you suggest a good all around book that would be good for a beginner?
Best thing is youtube or Google tutorials. Are you can do like I did when I got out high-school in 2006. I thought I knew it all and was ready to start welding off the bat but I was convinced to just start as a helper in a fab shop and I learned more watching the welders weld 11 hours a day then I did in any school or books. I took my test after 6 months as a helper but before that I thought I was ready and knew it all but I was so wrong I barely knew anything I was like a welding monkey I knew how to do it but didn't know why or how it was all happening so I wasn't ready to fix things that wasn't already perfect like they are in welding schools.
Has anyone verified the amp output on this one with a AC/DC clamp meter? I bought a 220v 250a HZXVOGEN hvm270 and the output was roughly half the setting. 200a setting read in the high 80s....
Is this on 220? I was looking at the hvm270 due to alleged high amperage but am now considering the one in this video due to lower alleged amp control for sheet metal.
@@idontwantcorporateretaliat6301 yes it was on 220 the unit was defective and the seller pulled the item off their store. Went with the hitbox mig-200PRO instead and have been very happy with it. Has proper output just doest have the plasma cutter.
@@pauleggert1863 Do you know what this LCD one offers over the MIG250? Does it have DINSE 25 or 50 connectors? 6-5r plug or 120 to 220 adapter? I'm considering this but the arccaptain 200 seems to offer upgrades in those areas from what I can see.
Saludos desde Venezuela Maracaibo estado Zulia. Hermano cuánto cuesta eso máquina de soldar Tig en dólares por favor y podrías pasarme el link por dónde la conorastes
I have just got the same machine. With mine there's a Burn Back knob inside, what's this for? And after 5 seconds the wire feed speeds up and I see no way to slow it down, anyone else have the same issue?
Si pueden enviar la página para ver a entrar los precios y hacer una comparativa de los distintos modelos, para ver cual conviene más de acuerdo a nuestras posibilidades.
Thank you for a very competent high-quality video, I am far from a non-professional in welding, and my daughter became interested in arc welding, she is embarrassed by her hobby and trying not to miss your videos, she will master the ceiling. Thank you for your help, waiting for your new video 👍👍👍👍👍🖐️
The good news IS that a lot of spare parts are generic so you can buy them on others markets.
Standart key hole wheels (OD 30mm, ID10mm, width 10mm), mb15 torch parts...
What recommend brand multi weld parkside hitbox decapower or many other brand?
What is the difference between HITBOX SYN-mig200 pro mig welder and the synergic HZXVOGEN HBM2280 mig, both look identical in programming?
Made by same factory Hitbox
add bossweld and weldtec to the same list
Hello friend, I wanted to know what your experience has been with the welding machine and if you recommend I buy it?
การเชื่อมด้วย ลวดแต่ละประเภทแบบอะไรควันน้อย?
Hi, This is the same machine I got for Christmas! I'm new to the various welding techniques, except stick. The manual leaves a lot to be desired! What is the capped mig output used for? Any info you can give me I would be greatly appreciated. Thanks and keep up the great videos!
Some of these machines manuals say they can’t lift tig weld aluminum im curious why?
Because they don't have built-in high frequency units which is also why they are "scratch start" in Tig mode
@@neiltanner8473 they still can ac tig?
capped output is for spool gun. the four pins, 2 for spool gun motor and 2 for trigger switch. if you buy the hitbox spool gun, it has the right connector. i am trying to figure out which pins for the switch, so i can use those two pins for tig switch; probably need to remove the cover and see the wirings. the manual is very basic, and no schematic.
nice tool , would you prefer this over STAHLWERK CTM-250
Ctm has more features. It also has a plasma cutter. It is a whole other category
Thank you very much sir for this great review, it helps a ton.
Glad it was helpful!
Hello,
I use this welding machine since 4 months now and I would like to give you m'y experience.
Like always with afordables chinese tools, the accessories are poor quality (gas tube, hammer).
The graphite wire feeding is well made. There IS 3 wheels wire feeding (0.6 to 0.8 and 0.8 to 1mm Vshaped for steel wire and a 1 to 1.2 mm Ushaped wheel for aluminium). You need to buy Kshaped wheels to experience a better flux core steel welding.
Functions :
- TIG lift is usable but without a gas electrovalve regulation or high frequency starter, its not very usable for stainless steel or wathever.
- MIG MAG IS quite good with synergic mode or manual mode. The welding IS great even if there are some parameters you need to adjust according to your welding position.
The wire roller system with only 2 rollers does well with 1kg and 5kg wires. BUT you need to clear thé system often to keep it safe.
- no complains with MMA, good penetration, arc stability and take off with rutiles sticks (basics sticks require a larger U0 than thé machine has but it works nowadays).
Spare parts are lacking on hitboxweld website distribution (for example, there's no wheels, no gas diffusor and no parts replacement for thé machine).
To conclude, I think this IS a good welder if you compare welding quality and cheap cost and if the welder keeps working after Time pass.
I dont think it will last 20 years like my old SAF fro AC MMA welder but today inverters have a lot more electronic parts so its natural they suffer more.
I own another hitbox welder, a 200A pulse TIG with HF which last since 2 years (approximatively 200 hours welding) and works well on stainless steel even if arc stability under 30A IS worse than an esab, Miller or lincoln professionnal TIG.
Thank you for your feedback!
Do you recommended it for the DIY guy who does little house proyects or repairs on car exhaust systems?
Hello, of course this IS a good choice if you use it for house projects.
ear! Good day- excellent recording!🤞
Thank you kindly!
Are there any good 👍
My example works well with MIG-MAG for cobalt steel and I have also tested it with FLUX core which was ok but I don't like FLUX as it pops and smokes. I have not tested aluminum as it requires too much fixing. In contrast, the TIG LIFT system is totally useless. I have been chatting with Hitbox for 2 weeks and they are completely clueless about how a weld works. They send a video that shows how to handle/set up the welding for LIFT. Totally worthless, they have to dab the tungsten electrode (which is blunt!) a lot of times before they ignite. They increase the Amp setting to get the welder's recommendation to over 130 Amps
Would be nice if you cleaned the welds you are showing. And what about penitration? No snap test ir at least a butt weld so we can see
Hi, was your aluminium welding done with gas or flux core wire?, if gas then which gas?. Many thanks my friend.
Argon
You are mistaken as most of users of this welding machine or it's previous version HBM2280. Welding with fluxcore self-shielding wire (FCAW mode) needs to be done on straight polarity i.e. "-" on torch and "+" on detail. Incorrect polarity is the main cause of severe slagging and spattering of metal. You may reconnect the cable on the front panel and redo the test. You'll see the much better result!
Thank you but you didn't show us if it support lift-arc (spot welding) which is what many need from TIG welding (cold welding)
+
ซื้อครบชุดรวมหน้ากากและแว่นถุงมือด้วยและตัวเครื่อง สัญญาลักษณ์ตัดไฟรั่วและป้องกันoverheat มาตราฐาน [มอก ?]
Tengo una hitbox 200 amp, mig , tig MMA ❤️
سلام خسته نباشید عالی احسنت. ببخشیدقیمتش چنده این دستگاه الماس بنفش
429EUROS
A professional video from someone who obviously does lots of welding, as a beginner what would make this video even better would be some explanation either as a voiceover or some pop up text to explain what and why you are doing it. Many thanks.
Great point! I will start making narrated videos soon
@@MakeAndTest RUclipsrs such as yourself doing very valuable job of bridging the user manual.
what gas choices do i have for tig welding aluminium with this machine
100% Argon
Hi make and test. I bought one of this hitbox SYN mig 200 pro welder. Mine's did not come with the tig torch, so I order one but the input end is too small for the connection port. I don't know where you get yours. I'm asking if you can provide me a link for one. Or where can I get it. Can I also get the dimension and the measurement for it and a code number if it has any?.
Please contact the seller/ manufacturer. I only made an unboxing video, and cant help you with that.
นาม Hitbox ตู้เชื่อมเอนกประสงค์ #?
ตู้เชื่อมรุ่นใหม่ ต่อเชื่อม แอพใด้ ตั้งระยะเวลาของงานใด้และมีเสียงเตีอนก็ดีนะ
Hi I bought the 200ii, any idea which Tig torch will fit, the plugs seem larger than average. Thanks.
اين توجد نقاط البيع . في الجزائر . شكرا
Nice review of this machine sir one my questions this machine duty cycle.
I dont have that information. You can probably google search that info.
Qual é o preso da maquina
@@gabrieldacostarocha1005 I can't understand your language sir please write English.
@@MakeAndTest ราคาเท่าไรครับ
Hi again, Another question. What tig torch should I get for this machine? Thanks again! Also, can you suggest a good all around book that would be good for a beginner?
Scratch start type with gas control knob on torch handle
Best thing is youtube or Google tutorials. Are you can do like I did when I got out high-school in 2006. I thought I knew it all and was ready to start welding off the bat but I was convinced to just start as a helper in a fab shop and I learned more watching the welders weld 11 hours a day then I did in any school or books. I took my test after 6 months as a helper but before that I thought I was ready and knew it all but I was so wrong I barely knew anything I was like a welding monkey I knew how to do it but didn't know why or how it was all happening so I wasn't ready to fix things that wasn't already perfect like they are in welding schools.
Bonjour comment avoir? Le prix?
Tig için töre kutuda varmı,ayrıca alınabiliyor mu
you can find it on amazon
Como que faço pra comprar uma máquina dessa, e qual é o valor dela
link na descrição
soy de Venezuela como haria en donde y que precio tiene esa maquina
@@MakeAndTest
EXCELENTE VIDEO¡¡... SALUDOS DESDE MEXICO¡¡
harika makine umarım bizede denemek için bir gün gönderirler
Kardeş bu makinanın fiyatı ve nerden temin edebiliriz
Ne kadar fiyat Turkiyede bulabilirmiyim!??
En cuanto sale todo
Are there any good on mig tig and mma welding
Why pushing instead of Dragging?
wow, very professional welding testing video, if you need our HITBOX welding machine, welcome to contact us freely
Slm ben sizin bu makinanın fiyatı nedir acaba Türkiye Eskişehir de gönderim maliyeti nedir acaba
Has anyone verified the amp output on this one with a AC/DC clamp meter? I bought a 220v 250a HZXVOGEN hvm270 and the output was roughly half the setting. 200a setting read in the high 80s....
Is this on 220? I was looking at the hvm270 due to alleged high amperage but am now considering the one in this video due to lower alleged amp control for sheet metal.
@@idontwantcorporateretaliat6301 yes it was on 220 the unit was defective and the seller pulled the item off their store. Went with the hitbox mig-200PRO instead and have been very happy with it. Has proper output just doest have the plasma cutter.
@@pauleggert1863 Do you know what this LCD one offers over the MIG250? Does it have DINSE 25 or 50 connectors? 6-5r plug or 120 to 220 adapter? I'm considering this but the arccaptain 200 seems to offer upgrades in those areas from what I can see.
السعر كام يا هندسه
ok you've had it 7mths is good or no
Good
Saludos desde Venezuela Maracaibo estado Zulia. Hermano cuánto cuesta eso máquina de soldar Tig en dólares por favor y podrías pasarme el link por dónde la conorastes
link en la descripcion
Cavab verin.
good machine
Gostei muito qual é o valo
A
Cuanto bale el equipo
I have just got the same machine. With mine there's a Burn Back knob inside, what's this for?
And after 5 seconds the wire feed speeds up and I see no way to slow it down, anyone else have the same issue?
Contact the manufacturer
Отлично! Спасибо!
Si pueden enviar la página para ver a entrar los precios y hacer una comparativa de los distintos modelos, para ver cual conviene más de acuerdo a nuestras posibilidades.
En Amazon encuentras éste modelo y varios de los que en éste canal se muestran, aquí mismo están los links.
آلیس ساخت کجاه
Very Nice Review. Just bought one on a Blackfriday Sale! lol
how much on black? :)
Like this mission price
इस मशीन की प्राइस कितनी है भाई
This unit is available in philippines and how much??
Mga 25k yan boss sa lazada
How much 4n1 MIG,TIG,MMA
Wow nice
या वेल्डिंग ची किंमत काय आहे मोबाईल नंबर पाठवा कुठे मिळेल माहिती पाठवा
Donde esta disponible
nerden alabilirim bu makineyi
This machine uses argon right ?
Gas and gasless for mig, gas for tig
how to order pls
Price plz
I MUST KNOW THE (FEED MAXIMUM) DIFFERENCE BETWEEN 110 AND 220V POWER. 10. M/MIN IS ALL I GET WITH 110
Quanto. Costa ,o visto ch'è vengono belle saldatura
How much does it cost?
gde to 200eur na alike
nyimak..bagus banget mas
ราคาเท่าไหร่ครับ
Rs???
Machine rate list
Price
Check description
How mach.pries
Φοβερό εργαλείο
$ ????? Price
429EUROS
@@mayleblon5035 made in china this product. ?
Amei está máquina
Fiyat ne kadar?
Place price
А почему 4 в одном, 4 вид какой,я только 3 увидел
👍
Где купит такой сварочни апарат
На Али экспресс они есть
Indonesia ada kh
Dónde puedo comprar esta máquina y la remiten a Peru región piura ciudad de piura gracias a y cuánto vale gracias
Prize
Saan po Maka order po at magkano po may tindahan ba mga pwedi bilehan po
prix soudure inox argon
Makina tipi nedir….hanki ülkede ,nereden kaça aldınız
Available throughout Europe, searchable on top of Amazon. Discounts are available now.
या वेल्डिंग ची किंमत काय आहे मोबाईल नंबर पाठवा कुठे मिळेल माहिती पाठवा
سعر كام
How much price
Check description
Price for india
Me interesa comprar una soldadora como está , alguien me puede ayudar con información, gracias
Dónde se compran
Is very very nice one
Which price
Check description
The price masen
Pakistan not aylybal
Magkano?
ราคาเท่าไร
Precio de la maquina
Maşnın qiyməti nə qədərdir,?
how much
439.99EUROS now
ชชุดนี้ราคาเท่าไหร่
Agregar.una.pagina.donde.sepuedenadquir.eltelefono.la.direccion.para.mejor.informacio
💪💪💪👍👍👍🔥🔥
Pries
Link in description
Cit costa acest aparat
Magkano yang 4 in 1
Eska kimmat bataye
Quero saber o preso em real
Onde compro no Brasil
ราคาเท่าไร