Our booth is 50 inches wide and we reclaim 12 screens at a time , no dip tank. 12 screens per hour . Yes it's fun and therapeutic . Great video !!! If you enjoy your job , you never work a day in your life.
@@gooseworksscreenprintingst9581 The dip tank is not necessary. First on the left side of the booth we line up 12 screens - we have Neumann roller frames (40) next we get the first screen, hit it with ink degrader and sponge it, placing it on the right side this process goes through the 12 screens. next we hose down the last screen we cleaned and move it to the left side until we finish the twelve next we spray reclaimer on the first screen (ATS reclaimer concentrate, mixes 1 ounce per gallon of water) after we spray it, we place it on the right side repeat till all 12 have reclaimer on them. Then we get last screen sprayed with reclaimer and hose it down, this reclaimer works basically instantly so there is no "wait time". Rinse the screen and put it on the left side until all twelve are done. We then spray them with Pro Wash degreaser/dehazer, same left to right process. after last screen is sprayed and sponged down, we start rinsing them in the same process, except that with this final rinse we just but it to the side to dry. the screens are about 20 inches wide, so the screens being on the left never touch the screens on the right because there are about 20 inches in the middle as a work area. AFTER all the reclaiming and dehazing is done, we rinse out our booth and we are ready for the next batch.,
Depends on the chemistry in your tank. Some, like SAATI chemicals, allow you to simply "dip" them for 45 seconds and that's all it takes. Others require an actual soak of about 5 minutes. Contact your local distributor and see what the best product is for your setup.
30 year ago we just used paint strpiper both sides leave then hit it with a jet wash with the power to take your arm off if you used it 1 handed then dry then recoat we evern made are inks up from scratch and our gums working on 100mtr tables lifting the screens by hand with constant heat ducts above on full bast we used to use car body filler with thinners to pin hole the screens aswell
Unfortunately I'm not the factory closed 4 years after I started but China was taking all things like that over there if we would have known all them years ago that every one would be wanting merch then maybe we would have carried on but it was a dieing trade back then few and far between
Okay, you've made us all want to run into our dark room for a reclaim day!! Love this. Bam boom! Thanks for the shout out 🤘
Wooaaa!! thanks for the comment, y'all are awesome!!
We're here to educate, entertain, and inspire! haha
good video dude
Thanks brother! Glad you enjoyed it.
Our booth is 50 inches wide and we reclaim 12 screens at a time , no dip tank. 12 screens per hour . Yes it's fun and therapeutic . Great video !!! If you enjoy your job , you never work a day in your life.
Wise words, my friend. Thank you for the comment! No dip tank? interesting. You should make a video!
@@gooseworksscreenprintingst9581 The dip tank is not necessary.
First on the left side of the booth we line up 12 screens - we have Neumann roller frames (40)
next we get the first screen, hit it with ink degrader and sponge it, placing it on the right side
this process goes through the 12 screens.
next we hose down the last screen we cleaned and move it to the left side until we finish the twelve
next we spray reclaimer on the first screen (ATS reclaimer concentrate, mixes 1 ounce per gallon of water)
after we spray it, we place it on the right side repeat till all 12 have reclaimer on them.
Then we get last screen sprayed with reclaimer and hose it down, this reclaimer works basically instantly
so there is no "wait time". Rinse the screen and put it on the left side until all twelve are done. We then spray them with Pro Wash degreaser/dehazer, same left to right process. after last screen is sprayed and sponged down, we start rinsing them in the same process, except that with this final rinse we just but it to the side to dry. the screens are about 20 inches wide, so the screens being on the left never touch the screens on the right because there are about 20 inches in the middle as a work area. AFTER all the reclaiming and dehazing is done, we rinse out our booth and we are ready for the next batch.,
Dude....Good stuff
Thank you!! Let us know if there's anything else you'd like to see. We want our channel to get better in 2024. Thanks!!
this was such a wholesome funny video, i love this
Thanks for the comment! So glad you enjoyed it. Hopefully it was helpful!
what do you do with your waste bucket
Dispose of it responsibly of course! Keep it green! keep it clean!
Great video! Loved it.
Thanks for the comment, Ronald. We're glad you enjoyed it!
What else would you like to see in regards to screenprinting?
Love that music choice 😂
How long is a long enough soak ?
Depends on the chemistry in your tank. Some, like SAATI chemicals, allow you to simply "dip" them for 45 seconds and that's all it takes. Others require an actual soak of about 5 minutes. Contact your local distributor and see what the best product is for your setup.
30 year ago we just used paint strpiper both sides leave then hit it with a jet wash with the power to take your arm off if you used it 1 handed then dry then recoat we evern made are inks up from scratch and our gums working on 100mtr tables lifting the screens by hand with constant heat ducts above on full bast we used to use car body filler with thinners to pin hole the screens aswell
That’s awesome! Thank you for sharing that! Hope you’re still printing🤘🏽🔥
Unfortunately I'm not the factory closed 4 years after I started but China was taking all things like that over there if we would have known all them years ago that every one would be wanting merch then maybe we would have carried on but it was a dieing trade back then few and far between
@@niceboy761 Sorry to hear boss! Hope all is well.
THANKS