Thank you so much for this info. I could not work out how to access settings mode, not realising I had to use the new transmitter combination. The manual only lists the old way. Typical. Thanks buddy 👍🏽
NINJA KIDD I learned from their official video from their website, but it’s only in Mandarin, so I think an English version should help more people able to access to this budget transmitter.
Dude same thing happened to me....1/8 arrma hit me in the shin at full throttle lol still hurts. Also mine tried to run away when i turn off the transmitter before i turn of my truck.
@@shaggysgcanimal how do u set the Killswitch or failsafe? Thats the problem i have lol....i got the end points an natural positions set on a throttle and steering. Still just wants to take off forward when I turn off my transmitter before I turn my truck off.
For me, my dumbo rc came already binded to the receiver. However, when I turn it on the car starts moving forward fast but the steering is working fine. I’ve tried to change the throttle trim but even with max throttle trim the car is still moving forward s medium speed. Do you have solution?
I haven’t tried the fail safe function as I used it mainly for my crawlers. You will need the X6YC receiver for setting this function. Press one on the bind button on the receiver, the receiver light will blink under setting mode then turn ur steering wheel/trigger to the position where u want it to stop, then press one more time on the button will do. To reset to factory setting just press the button one time and press second time within 5 seconds after the first press. Hope this help. Tqvm
thanks so much ,this video is very help me to get setting the one ..thanks ,man! hope you will share another about this controller such like up grade version,etc...success for you!
@@boykeification Both of this transmitter can bind with more than one receiver. The procedure to bind the receiver to the transmitter is to switch on the transmitter and connect the receiver with the power source, then you press one time on a little tiny button in the receiver (same button as gyro setting inside a tiny square hole on the side). You may refer to this video at 1:10
@@jeffreytfl5832 thanks man..i knew it that tiny button...i trial and error ,what happening if i press the button twice,seem like another setting because the light is reaction,but i dont know the seeting if i press twice...
Subbed bro!. Thankyou for the very helpful video. Just bought my dumborc x6 x6fg. And watched this video for the tutorial for binding, reset positions and activating the gyro. I just have a little problem. My steering is in reverse but on the button it is on (normal) but when i steer right it will steer left. Vice versa. what should be the problem? Or is there anyway that i can reset the transmitter to default or factory settings?
@@jeffreytfl5832 well at first it works correctly, after binding it, It was on (normal switch) and then after i messed up a little bit. And then i just noticed that the steering went to reverse without even switching it to reverse switch, then i decided to watch a tutorial and found ur video. All good, but the steering is still in reverse. I need to switch it on (reverse) so that i can steer it to the right direction. And thats not normal.
This is excellent information. I just got my Dumbo system with gyro and was not impressed with the included instructions. Now, I'd like to set up my Redcat Everest to use the Dumbo receiver to run 4 wheel steering. I've already made the conversion but I'm not happy with the standard receiver using a Y-cable and servo reversing adapter. Can you suggest a way--or refer to a video--to set up the transmitter to use 2 separate channels for the 2 steering servos. One of the channels will probably need to be reversed. Thank you for your help with what appears to be a bargain system. I paid $24 to Banggood for it.
I have got the (latest?) version of the Dumborg with the push buttons on top. I tried to connect a servo on the 3rd channel but it keeps interfering with the first channel. When I calibrate the transmitter and plug in the servo on the 3rd channel the steering wheels keeps going from left to right unbtill I turn the reciever off. After unplugging the 3rd channel it works as it should. But so I cannot use my 3rd channel for the gearbox. So...what do I do wrong?
You will need to reset the steering and throttle ever time you enter into the setting mode. Just turn your hand wheel all the way forward and backward then stay in neutral will do. And the procedure for the throttle is also the same
@@jeffreytfl5832 I did that several times but it still keeps this problem. The weird thing is that it worked great at the start but after a few short test rides the problem occured. I have 2 recievers and both have the problem.
after I set up ep for ch4 and turn of remote. It always returns to same full roation default position and brakes attached stuff. Is there way to stop servo returning to base position after remote is turned of?
Unfortunately the transmitter doesn't come with model memory so the setting on the transmitter is for all the receiver, if you change the setting, it will apply to the other receiver
Hi very good video, I'm having issues and trying to work out if my reciever or esc is broke, I put esc into channel 2 and servo channel 1, all I'm getting is a solid red light on my reciever, any help would be great Thank you
Well, before ending the video you showed how to reset the new version remote back to factory settings, but you didn't show it for the older version. Can you please write it down how to do it? Thanks.
For the old version, you can repeat the same procedure for entering the mixing mod again, then it will switch back to the normal mode with blue light is on
Hi. I was wondering if can you help me. I have a problem with my Dumborc x6 transmitter. On channel 4 I have a winch motor, and when I turn off the transmitter (ch4 button is in the neutral position) my winch motor turns on and I can turn it off, only if I unplug the receiver form the power. I have done some research online, and it seems to me that there is a failsafe on ch4 that activates when I turn the transmitter off, buy that failsafe is not setup to be in neutral position. Do you know how could I solve this problem? Thank you in advance.
I bought the x6 with a non-gyro reciever and a separate gyro for my rc drift car. The gyro has the option to adjust the gain from either the gyro itself or the reciever. Can i use the channel 5 or 6 knobs on the reciever to adjust the gain?
Sorry for the late reply, I'm not sure about your external gyro set up, but I believe the channel 6 is only to work with their own receiver with gyro function
I've got a problem with my dumborc x6. Steering goes the wrong way in normal mode, with switch set to reverse steering it's correct, but steering trim is now in reverse. Tuning the steering makes no sense when it does the opposite of what I'm trying to do.
Can you bind 2 different cars to the same transmitter?, it will bind to my arrma senton, but not my axial crawler, switched the receivers around and only the arrma connects
My channel 3 button lights up and goes on/off but output from channel 3 on receiver is always on. Do you know why this is? I cannot turn lights on or off with channel 3. They are always on? Thanks for help
I have dumbo rc x6 with gyro i have it hooked it up to my nitro car its work great bought another receiver to hookup to another nitro car so i can used the same remote control for both cars now the problem is on the second nitro car throttle only works in reverse it only works corectly for a second when i put throttle in reverse mode on transmitter it works perfect on my other nitro but new receiver is giving me issues am i doing something wrong i followed binding process any help will greatly be appreciated
Hi Jeffrey, I connected my light bar to Ch3 but it doesn't turn off. It appears power is constantly on. In fact it there is constant power on all channels 3,4,5 & 6. All the switches on the transmitter work because I tested them by plugging in a servo to all the channels. How do I set up to turn on/off my light bar? Thx
Sorry but I don't understand one thing, "In the mixed mode" how does it work for the crawlers if the channel one operates both the steering and the engine at the same time? You put a servo in the channel 2, but the channel 2 is dedicated to the Esc control unit, then moving the steering at the same time the engine is activated.
@@jeffreytfl5832 I'm building a crawler and I'm trying to understand how it works, what kind of control unit I need to have the function that allows you to block a single engine on the moa crawlers with two motors. Maybe you could advise me what to look for.
Need help with the Dumbo controller. So I ch.1 steering, 2 throttle, 4 winch, not using gyro.... how can I set up Rear Steering on an independent channel. I want to be able to choose left to right to no rear steer. I also want to keep winch. Please help with set up
@@jeffreytfl5832 I did that and even have a video which I sent to DumboRC so they could review it - ruclips.net/video/pnuiJ5Ucvpk/видео.html - doesn't help
so do I need an on/off switch attached to the receiver in order to control my lights? Plugging it into channel 4 does not do anything? Do I need to set that button in order to control the lights?
It's a good thing I came to your video I have the zino one. But when I drive it not even 20 ft starts losing signal then it takes off on its own does it need to be rebinded
EP adjustment is for channel 3 and 4, the setting is to enter the setting mode and using the setting knob on top (for ch 1 and 2) to set the 3 & 4, pls refer my video
I just installed the dumbo x6 and a hobbywing max 10 esc and im getting a ton of lag on throttle and brake and reverse dont aleats engage first time i try it...does anybody know if thats a problem with the remote or is it the esc ?
Is it possible to reverse channel 5 and 6? I've looked all over the internet, but I cannot find anyone describing how to do it (or saying that it's not possible).
@@jeffreytfl5832 I’ve seen it on Bangood. It’s 3 channel on/off switch. The LED lights i’m connecting has 3 wires. I think it has it’s own circuit. Will that work?
My transmitter stays slowly blinking blue. I've entered into settings mode and moved the wheel and trigger back, forth, and neutral. But after I get out of settings mode, it still continues to slowly blink blue. I've put in fresh batteries and still have the same issue. Everything works fine even with the blinking light, thankfully. But any thoughts on how to get the light to stay solid blue?
@@jeffreytfl5832 thanks for the reply! It's slowly blinking blue before entering settings mode too. I've put fresh AA batteries in it and a fully charged lipo battery too. Still slowly blinks blue. 🤔
@@jeffreytfl5832 my problem is fixed now. I guess I had a really unlucky case of 3 sets of batteries with issues... I'm not positive but I think it was because I was putting in lithium AA batteries. They were new out of the package. But once I put in akaline AA batteries, the blinking light when away. 🤔 Thanks anyways!
How come when I use the steering wheel it uses the throttle at the same time. I have put the wires correctly.. Also the light on my controller shows red light instead of blue
@@jeffreytfl5832 never did that before but I've never had this issue before. But due to that mistake i definitely will make that a habit lol thanks man.
Cheap way is to put small rubber band over the part the carb filter fits on put the other end on your linkage from throttle servo...when you loose power the bands will close the carb 💨 and stop the car no more run aways
I can’t get mine to go into mixed mode. When I hold the wheel and throttle all the way forward and switch it on the light blinks red and blue, and when I press in the throttle to switch it, it does nothing, then goes back to blue after a minute. Haven’t seen anybody else have this problem, is there something I’m doing wrong?
Solved!!!! After about an hour of watching the same tutorials over and over, I figured it out thru trial and error. I guess maybe there’s been a newer model since the videos I saw, but the missing piece is clicking the channel three button after reaching the red/blue blinking light. It will then blink steady blue like it does in the videos, and you can use the throttle to choose between mixed and normal steering.
Thank you so much. The first video to show actually what I needed.
U r welcome
Thank you so much for this info. I could not work out how to access settings mode, not realising I had to use the new transmitter combination. The manual only lists the old way. Typical. Thanks buddy 👍🏽
NINJA KIDD I learned from their official video from their website, but it’s only in Mandarin, so I think an English version should help more people able to access to this budget transmitter.
Great video, got mine today and my car took off in my kitchen. Wish I'd seen this first. I set end point at full throttle lol
Dude same thing happened to me....1/8 arrma hit me in the shin at full throttle lol still hurts. Also mine tried to run away when i turn off the transmitter before i turn of my truck.
@@kentucky4696 remember to set kill switch and throttle end zones was my mistake lol
@@shaggysgcanimal how do u set the Killswitch or failsafe? Thats the problem i have lol....i got the end points an natural positions set on a throttle and steering. Still just wants to take off forward when I turn off my transmitter before I turn my truck off.
@@kentucky4696 it's in the video dude.
@@shaggysgcanimalyeah, i watched it again an found out how to do it haha thx man.. I thought all he was doing was setting the end points.
wow nice. god job man. this information is very good to me. because i dont understand how to make mixed mode. thanks for the video ...
Thank you!
For me, my dumbo rc came already binded to the receiver. However, when I turn it on the car starts moving forward fast but the steering is working fine. I’ve tried to change the throttle trim but even with max throttle trim the car is still moving forward s medium speed. Do you have solution?
Looks like you have to reset the neutral position like what I did in this video.
Did you ever figure this out?
@@CuddleComedy are you having the same problem?
finally my dual servos work.sorry bout dat.top video
Thanks for a great video. Do you know how to set the Fail-safe function?
I haven’t tried the fail safe function as I used it mainly for my crawlers. You will need the X6YC receiver for setting this function. Press one on the bind button on the receiver, the receiver light will blink under setting mode then turn ur steering wheel/trigger to the position where u want it to stop, then press one more time on the button will do. To reset to factory setting just press the button one time and press second time within 5 seconds after the first press. Hope this help. Tqvm
thanks so much ,this video is very help me to get setting the one ..thanks ,man! hope you will share another about this controller such like up grade version,etc...success for you!
boykeification Glad to know it helps 👍
@@jeffreytfl5832 if buy seperate between transmitter and reciever or if i wanna add one reciever again,how to bind? thanks man
@@boykeification Both of this transmitter can bind with more than one receiver. The procedure to bind the receiver to the transmitter is to switch on the transmitter and connect the receiver with the power source, then you press one time on a little tiny button in the receiver (same button as gyro setting inside a tiny square hole on the side). You may refer to this video at 1:10
@@jeffreytfl5832 thanks man..i knew it that tiny button...i trial and error ,what happening if i press the button twice,seem like another setting because the light is reaction,but i dont know the seeting if i press twice...
@@boykeification OIC, that's to change the servo direction of the gyro function.
Thanks you for the video, very helpfully, i set up my dumbo 6ch back to neutral positions sucessfully, sr for my english if something went wrong!
You are welcome
Thanks for uploading this, like 👅
Subbed bro!. Thankyou for the very helpful video. Just bought my dumborc x6 x6fg. And watched this video for the tutorial for binding, reset positions and activating the gyro. I just have a little problem. My steering is in reverse but on the button it is on (normal) but when i steer right it will steer left. Vice versa. what should be the problem? Or is there anyway that i can reset the transmitter to default or factory settings?
I think it is not the transmitter issue, it is how the servo position so the normal/reverse switch is for us to adjust for its direction
@@jeffreytfl5832 well at first it works correctly, after binding it, It was on (normal switch) and then after i messed up a little bit. And then i just noticed that the steering went to reverse without even switching it to reverse switch, then i decided to watch a tutorial and found ur video. All good, but the steering is still in reverse. I need to switch it on (reverse) so that i can steer it to the right direction. And thats not normal.
This is excellent information. I just got my Dumbo system with gyro and was not impressed with the included instructions. Now, I'd like to set up my Redcat Everest to use the Dumbo receiver to run 4 wheel steering. I've already made the conversion but I'm not happy with the standard receiver using a Y-cable and servo reversing adapter. Can you suggest a way--or refer to a video--to set up the transmitter to use 2 separate channels for the 2 steering servos. One of the channels will probably need to be reversed. Thank you for your help with what appears to be a bargain system. I paid $24 to Banggood for it.
This transmitter does not have crawler steering (4 wheel steering) settings.
Thank you! I though mine is broken or something, but in turns out is to enter settings is totally different than the given manual!
Ted Hob Me too, until I found the video from their website. So I decided to make a video for those people having the same issue like us😀
@@jeffreytfl5832 yeah, I already tried to find info on their site, but can't find it. Thanks again friend :)
@@tedhobby You are welcome 👍
Did not you experience when dumborc steering direction is working opposite? Directions switch in normal position
I have the one your holding in your right hand how do I program the fail safe for gas vehicle ? Been looking everywhere .. it's not in the directions.
I don't think it has the function.
Just found out there’s another version for gas vehicles with fail safe features, but I have not try it before as I don’t have any gas vehicle
Sooooo helpful, thank you. Any way to reverse 3 and 4 channel?
No, I don't think so.
Awesome! I was ready to smash it.
Thank you
Did you push the small button on the transmitter 3 times to activate the gyro function on the early version that said gyro inside or was it defective?
It was the receiver came with the transmitter does not have gyro function
I have got the (latest?) version of the Dumborg with the push buttons on top. I tried to connect a servo on the 3rd channel but it keeps interfering with the first channel. When I calibrate the transmitter and plug in the servo on the 3rd channel the steering wheels keeps going from left to right unbtill I turn the reciever off. After unplugging the 3rd channel it works as it should. But so I cannot use my 3rd channel for the gearbox. So...what do I do wrong?
You will need to reset the steering and throttle ever time you enter into the setting mode. Just turn your hand wheel all the way forward and backward then stay in neutral will do. And the procedure for the throttle is also the same
@@jeffreytfl5832 I did that several times but it still keeps this problem. The weird thing is that it worked great at the start but after a few short test rides the problem occured. I have 2 recievers and both have the problem.
minit 17.38 kalau lampu tu tak solid mcm dalam video kenapa erk?...jadi jadi blink blue + amber tapi blink slow2
Battery low for transmitter
Can you charge 4 AA on the USB port ? Thanks for your upload 🙏
I dun think the AA battery can be charged. Besides, if you are using small Lipo, it is better to use balance charger.
Very good presantation, leep it on!
What happens with the shaking of the transmitter to move the servos, it is any usefull?
Andreas Kassner that’s only happened when we didn’t reset the channel 1 and channel 2 after we done the setting. It’s mentioned in 5:00. Tq
after I set up ep for ch4 and turn of remote. It always returns to same full roation default position and brakes attached stuff. Is there way to stop servo returning to base position after remote is turned of?
Can the end point adjustments be different for each receiver or will it be the same for all? I have multiple receivers for different cars
Unfortunately the transmitter doesn't come with model memory so the setting on the transmitter is for all the receiver, if you change the setting, it will apply to the other receiver
Hi very good video, I'm having issues and trying to work out if my reciever or esc is broke, I put esc into channel 2 and servo channel 1, all I'm getting is a solid red light on my reciever, any help would be great
Thank you
Steering servo to channel 1 and esc to channel 2, hope this helps.
Mine is doing the same, thing how did you fix it?
@@The_Bored_Farmer it was my esc that was broke
Well, before ending the video you showed how to reset the new version remote back to factory settings, but you didn't show it for the older version. Can you please write it down how to do it? Thanks.
For the old version, you can repeat the same procedure for entering the mixing mod again, then it will switch back to the normal mode with blue light is on
Thank you very much
Hi.
I was wondering if can you help me. I have a problem with my Dumborc x6 transmitter.
On channel 4 I have a winch motor, and when I turn off the transmitter (ch4 button is in the neutral position) my winch motor turns on and I can turn it off, only if I unplug the receiver form the power.
I have done some research online, and it seems to me that there is a failsafe on ch4 that activates when I turn the transmitter off, buy that failsafe is not setup to be in neutral position.
Do you know how could I solve this problem?
Thank you in advance.
I bought the x6 with a non-gyro reciever and a separate gyro for my rc drift car. The gyro has the option to adjust the gain from either the gyro itself or the reciever. Can i use the channel 5 or 6 knobs on the reciever to adjust the gain?
Sorry for the late reply, I'm not sure about your external gyro set up, but I believe the channel 6 is only to work with their own receiver with gyro function
I've got a problem with my dumborc x6. Steering goes the wrong way in normal mode, with switch set to reverse steering it's correct, but steering trim is now in reverse. Tuning the steering makes no sense when it does the opposite of what I'm trying to do.
If you pick up the receiver you shake it you should hear a clicking noise inside clicking noise there's a gyro
My rc is moving by itself,my throttle is going crazy and i not even touch the throttle but my motor move by itself please help me
Have you entered into the setting mode without reset the throttle?
Sounds like Arnold Schwarzenegger. Cool
Accent. Could you please post a video of you saying,
“Get to the choppa!!!!!”?
Lolz, I will that your comment as compliment. Thank you
You took the compliment correctly. Love Arnold in his movie and we are constantly talking in his accent
Can you bind 2 different cars to the same transmitter?, it will bind to my arrma senton, but not my axial crawler, switched the receivers around and only the arrma connects
It can bind with multiple receiver
Is there a way to put the transmitter into bind mode?
It seemed to just connect to the arrma but my crawler nothing, I tried a short press on the bind button and a long press
My channel 3 button lights up and goes on/off but output from channel 3 on receiver is always on. Do you know why this is? I cannot turn lights on or off with channel 3. They are always on? Thanks for help
Check your transmitter battery voltage, it may be caused by low power
@@jeffreytfl5832 apparently I need a light module to allow it to switch but with the 4 channel versions you don't. Random.
I have dumbo rc x6 with gyro i have it hooked it up to my nitro car its work great bought another receiver to hookup to another nitro car so i can used the same remote control for both cars now the problem is on the second nitro car throttle only works in reverse it only works corectly for a second when i put throttle in reverse mode on transmitter it works perfect on my other nitro but new receiver is giving me issues am i doing something wrong i followed binding process any help will greatly be appreciated
Hi Jeffrey, I connected my light bar to Ch3 but it doesn't turn off. It appears power is constantly on. In fact it there is constant power on all channels 3,4,5 & 6. All the switches on the transmitter work because I tested them by plugging in a servo to all the channels. How do I set up to turn on/off my light bar? Thx
Need to know your wire connection, mine is working for constantly on and flashing for my roof light
Sorry but I don't understand one thing, "In the mixed mode" how does it work for the crawlers if the channel one operates both the steering and the engine at the same time? You put a servo in the channel 2, but the channel 2 is dedicated to the Esc control unit, then moving the steering at the same time the engine is activated.
The crawler that I mentioned is the crawler track eg, crawler crane and tank.
@@jeffreytfl5832 I'm building a crawler and I'm trying to understand how it works, what kind of control unit I need to have the function that allows you to block a single engine on the moa crawlers with two motors. Maybe you could advise me what to look for.
@@valerio2184 Just connect the channel 1 and 2 with the respective motor esc
Need help with the Dumbo controller. So I ch.1 steering, 2 throttle, 4 winch, not using gyro.... how can I set up Rear Steering on an independent channel. I want to be able to choose left to right to no rear steer. I also want to keep winch. Please help with set up
This doesn’t support 4 wheel steering for crawler, if you are looking for 4ws, you may look for the hobbyportal/turbo racing 7ch transmitter
I can't reach the max speed in forward but only in backward, can you help me please?
Pls ensure u have done the reset for the throttle every time when u enter into setting mode. Another possibility could be due to the esc setting.
The sub trim for channel 1 (steering) is opposite of the direction the vehicle or boat is going. How do you correct this?
aa240sx you may check the reverse switch for the channel 1 at the top of the transmitter
@@jeffreytfl5832 I did that and even have a video which I sent to DumboRC so they could review it - ruclips.net/video/pnuiJ5Ucvpk/видео.html - doesn't help
aa240sx ok, let me check with your video link first
I checked mine is same as your, it is in opposite direction
so do I need an on/off switch attached to the receiver in order to control my lights? Plugging it into channel 4 does not do anything? Do I need to set that button in order to control the lights?
I will be doing a new video for its new receiver which comes with the light module.
@@jeffreytfl5832 yes I saw that one, I already own two so I purchased the on/off switch for controlling the lights. I will be watching
It's a good thing I came to your video I have the zino one. But when I drive it not even 20 ft starts losing signal then it takes off on its own does it need to be rebinded
Thanks for your comment, I have never encountered this issue before, perhaps you may want to rebind the receiver with the transmitter.
I try that and nothing happened just do the same thing what I probably need is maybe a glitch buster maybe that could be the issue
Thanks for video, I just got my x6.
I entered the setting mode but still cannot understand how to set the EPA. Any help ?
EP adjustment is for channel 3 and 4, the setting is to enter the setting mode and using the setting knob on top (for ch 1 and 2) to set the 3 & 4, pls refer my video
Hello, can you tell me which number on the receiver that I should connect the battery box power to?
The power is connected through the ESC to the receiver channel 2
I just installed the dumbo x6 and a hobbywing max 10 esc and im getting a ton of lag on throttle and brake and reverse dont aleats engage first time i try it...does anybody know if thats a problem with the remote or is it the esc ?
Not sure what cause the problem, it could be due to the sensorless brushless esc
@@jeffreytfl5832 it was the esc the motor im running is sensored so it didnt work well with the esc...i just got back into r/c so i didnt know
How do you set servo endpoints on the dumbo rc radio
Dun think it has this function for channel 1
wow ...nice way to have 4WS
Hi. I've got a surpass 6ch . It didn't come with gyro. Do you think a gyro Rx will work ?
If I remember correctly, surpass transmitter will work with dumbro gyro receiver. The surpass receiver does not have gyro function
@@jeffreytfl5832 means the gyro function won't work
@@nigellloyd1860 I mean the surpass receiver does not have gyro function not the transmitter
Hey thanks for the help those directions are crap on the paper! Was way easier to follow what you did!
Tqvm
How to reverse gyro 👌
D Smith RC press the tiny bind button on the receiver twice will change the direction of the gyro, hope this help.😊
Is it possible to reverse channel 5 and 6? I've looked all over the internet, but I cannot find anyone describing how to do it (or saying that it's not possible).
I don't think channels 5 & 6 have the reverse function
How bout , how to reverse 3 and 4 channels?
David did you find a solution for this? Also looking to reverse channel 5 & 6...
Is there a way to use channel 3 on the receiver to control LED lights on the transmitter? Thank you in advance
You will need a RC receiver light control switch panel to connect between the receiver and the lights
@@jeffreytfl5832 I’ve seen it on Bangood. It’s 3 channel on/off switch. The LED lights i’m connecting has 3 wires. I think it has it’s own circuit. Will that work?
@@albertcua8571 The switch has a small board that can connect two set of led connector
Can you use the ch5 to control lights or something else than the gyro function, when the receiver is not in gyro mode?
Yes
@@jeffreytfl5832 perfect
My transmitter stays slowly blinking blue. I've entered into settings mode and moved the wheel and trigger back, forth, and neutral. But after I get out of settings mode, it still continues to slowly blink blue. I've put in fresh batteries and still have the same issue. Everything works fine even with the blinking light, thankfully. But any thoughts on how to get the light to stay solid blue?
Usually it cause by battery is running low. What about before u entered into settings mode?
@@jeffreytfl5832 thanks for the reply! It's slowly blinking blue before entering settings mode too. I've put fresh AA batteries in it and a fully charged lipo battery too. Still slowly blinks blue. 🤔
@@jeffreytfl5832 my problem is fixed now. I guess I had a really unlucky case of 3 sets of batteries with issues...
I'm not positive but I think it was because I was putting in lithium AA batteries. They were new out of the package. But once I put in akaline AA batteries, the blinking light when away. 🤔
Thanks anyways!
@@gmendoza66 OIC, that's great you have solved the problem 👍🏻
How come when I use the steering wheel it uses the throttle at the same time.
I have put the wires correctly..
Also the light on my controller shows red light instead of blue
Check the video 10:10, I have explained how to change the setting for your question. Tq
@@jeffreytfl5832 ahh okay.. thanks.
But is there a way to turn off the gyro mode?
@@flipsilog_Gaming press the tiny button on the receiver 3 times will activate and deactivate the gyro 2:50
How do u set up failsafe....my rc truck runs away every time i turn off the transmitter.
For safety reason, I only turn on the transmitter before turn on the esc, and turn off the esc before turn off the transmitter.
@@jeffreytfl5832 never did that before but I've never had this issue before. But due to that mistake i definitely will make that a habit lol thanks man.
Cheap way is to put small rubber band over the part the carb filter fits on put the other end on your linkage from throttle servo...when you loose power the bands will close the carb 💨 and stop the car no more run aways
@@Greenbear39 pretty slick man, but I only run electric cars
I can’t get mine to go into mixed mode. When I hold the wheel and throttle all the way forward and switch it on the light blinks red and blue, and when I press in the throttle to switch it, it does nothing, then goes back to blue after a minute. Haven’t seen anybody else have this problem, is there something I’m doing wrong?
Solved!!!! After about an hour of watching the same tutorials over and over, I figured it out thru trial and error. I guess maybe there’s been a newer model since the videos I saw, but the missing piece is clicking the channel three button after reaching the red/blue blinking light. It will then blink steady blue like it does in the videos, and you can use the throttle to choose between mixed and normal steering.
Do you put in X4 tx a 2s lipo our 3s lipo?
No
How do I enter the controller into booting mode so I can Boudet to boot it to a car
Hi. What do you mean boudet to boot it to a car?
Are those receivers compatible with each other??
Yes
Great video thanks👍
How to set up 5,6ch EPA.
EPA adjustment is not available for ch5 & 6, but i think they have pre set the servo travel at 38% for button switch version
@@jeffreytfl5832 It was difficult to apply trx4 mini servo, so I was looking for a way. It's a 6ch button method. Thank you for your answer.
Does anyone know how to bind the receiver and transmitter??
My blue light is always solid. How do I get controller to go into bind?
Mine won’t reverse
Is it factory setting out of the box? U may try to check the dial on the top of the transmitter for the forward and backward settings
My receiver ligh on is red, why ?
U r in another mode, pls check my video, there is an explanation for how to switch the control mode.