The arduino nano can power a 150 led string of eco wsb2812s without a external power supply. They where set at a lower light level but plenty bright. I tested it at my moms house and her neighbors liked it alot. I started with regular 2812s but the ecos are have much better efficiency and are cheaper as well.
hello, but my serial monitor showing, starting Ws2812Fx setup, wifi setup to connect to the wifi, then again starting ws2812fx setup. and this going on and on in a loop. On my router, I can see no esp is connected. can u help me out pls
Hey dude, I have a couple of problems with my programming; Would you please help me? When i upload the program to the esp01s the WiFi disappears and when i change the program ro default WiFi appears... I'm using ESP01s with relay v4
The ESP-01 has several disadvantages. VCC and Enable must be set to 3.3 volts. The 3.3 volt voltage regulator is missing. The flash is only 1MB. It cannot be installed via the web installer and online update does not work. Software version 0.14 does not work, version 0.13.3 must be used. The range of functions is limited. It is better to use a Wemos Mini d1 or an ESP32 board.
Hi, im trying to do this but i think the wiring is wrong, i have the lm1117 for 3.3v to power the esp01, just like your diagram and it does not work, the only way it worked was when i aslo connect the CH_PD to the 3.3v and i disconnect the ground from the led strip, please help i been trying for a couple of hours and its driving me mad. im using a 5v
its been the same, it works perfectly if i disconnect the signal from the stip/arduino and then power it on,and then connect the signal from strip/arduino back...any thoughts?
As he states in the video, the code can also be found under File>Examples>WS2812fx>esp8266_webinterface There are also many more great code examples in that directory as well. Poke around. Have fun.
The arduino nano can power a 150 led string of eco wsb2812s without a external power supply. They where set at a lower light level but plenty bright. I tested it at my moms house and her neighbors liked it alot. I started with regular 2812s but the ecos are have much better efficiency and are cheaper as well.
Congratulations.
With wifi?
What a phenomenal piece of work, thank you for sharing the code and the video 👏👏👏
Thank you so much for this video.
Welcome 😀
The USB cable you used to connect to the controller: anything fancy? Or did you simply splice usb to servo?
Is it work on ws2811
i love the web ui cuz it has a lot of effcts but i also just wanna add support for echo so i dont have to keep opening the link to control the lights
How can we do the same effects with the blynk application?
You've to change the entire code.
In the Blynk App, there is an option available for controlling the RGB LED bulbs.
Is this possible for 2 different strip with same esp8266, and also change colour separately.
bro how much leds supported by the esp 01 / nodemcu ?
That will depend on the power supply you use and not the esp-01 or nodemcu!
Hey Bro can I use esp-01s for this project?
esp-01 and esp-01s is the same but different memory and built-in LEDs
Where did you got the strip? i cant find it in your store
Very soon it will be available.
Or you can call to our shop for this item.
If possible, they'll mange it for you.
If I was to create high power probably 100 watt RGB strip how to do it? I want to use it as aquarium light hence LED may not be addressable.
Thanks
You'll need a much powerful power supply of 100watt.
use smd5050
hello,
but my serial monitor showing, starting Ws2812Fx setup, wifi setup to connect to the wifi, then again starting ws2812fx setup. and this going on and on in a loop. On my router, I can see no esp is connected. can u help me out pls
Hello sir,
How do I upload this example code in esp32s.
Hey dude, I have a couple of problems with my programming; Would you please help me?
When i upload the program to the esp01s the WiFi disappears and when i change the program ro default WiFi appears... I'm using ESP01s with relay v4
use esp12e board
Thanks bro,
can ws2812B work?
Hello your Adafruit Neopixel version ?
I'm using Chinese version.
Each diode has WS2812 IC as controller.
@@ElectronicsBd I can add Micrófono module and ws2812 controller?
Is it possible to use alexa with this?
The ESP-01 has several disadvantages. VCC and Enable must be set to 3.3 volts. The 3.3 volt voltage regulator is missing. The flash is only 1MB. It cannot be installed via the web installer and online update does not work. Software version 0.14 does not work, version 0.13.3 must be used. The range of functions is limited.
It is better to use a Wemos Mini d1 or an ESP32 board.
Hi, im trying to do this but i think the wiring is wrong, i have the lm1117 for 3.3v to power the esp01, just like your diagram and it does not work, the only way it worked was when i aslo connect the CH_PD to the 3.3v and i disconnect the ground from the led strip, please help i been trying for a couple of hours and its driving me mad.
im using a 5v
its been the same, it works perfectly if i disconnect the signal from the stip/arduino and then power it on,and then connect the signal from strip/arduino back...any thoughts?
can I use for this connection led SK6812?
I'm not sure, You can try.
I've used WS2812 LED strip.
I don't think It will wok with SK6812
I've tested it on SK6812 and it works
@@knowhood how was your settings?
@@knowhood thanks for sharing this info
@@marekbalco9594 it's exactly the same with WS2812
Can i buy this or order this
If You're living in Bangladesh, you can.
www.electronics.com.bd
HELLO...
i got mine to work perfectly.... but could you show how
or if possible to have it working in node red... controlling
thanks
I never used Node Red before!!!
its posible with ESP32?
yes
Excellent! number code of regulator voltage and capacitor?
every thing ok big problem is wifi disconnecting if change effects everytime
can add Micrófono module?
I was unable to connect to wifi.
how do we do this?
Where do I find the code
Anybody not able to connect to the web ip on a mobile phone? Mine is fine from desktop, but not from iPhone regardless of browser.
👍👍
😍
merci infiniment, mais pouvez-vous m'aider a créer un sketch qui va me permettre d'envoyer les sms RFDI et module GSM. veuillez agrée ma demande merci
why led not respon
is there any way i can add support for alexa on this '?
Possible I think.
But, I never tried.
I think it is already available tasmota.github.io/docs/Getting-Started/, multiple such projects are there.
yea with a relay to kill the power or turn the power on it. You have 2 pins on that device.
Have the code?
how i do to control for alexa?
You may have to write codes for alexa.
Moreover, I never tried with Alexa orgoogle assistant
Code? pls
github.com/kitesurfer1404/WS2812FX/tree/master/examples/esp8266_webinterface
As he states in the video, the code can also be found under File>Examples>WS2812fx>esp8266_webinterface There are also many more great code examples in that directory as well. Poke around. Have fun.
pour les Français : ne pas oublier de désactiver votre wifi en 5 GHz et le mettre en 2,4 GHz dans votre routeur
sinon ca ne fonctionnera pas
VERY VERY WOREST SERVER DISCONNECTS EVERY TIME...reset and reconnect every time
lol ye, its sickening how expensive the adafruit stuff is. i feel like theyre abusing the tinkering market by overpricing sht to oblivion.