Thank you! I am a 74 yr. old widow and I have learned these hired repairmen know how to take advantage of "old ladies"; and, the legit repair people know how to charge. With the help of your video and the helpful man at Lowes, I was able to fix my leaky faucet myself! Thank you.
Pam Richardson I just went to the hardware store to get the replacement gasket and sprinkler parts - the old guy looked at me and asked if I was going to try to do it myself - I said “YES, I SURE AM!” To which he replied that usually took years of experience. I asked him if he didn’t think a woman (I;m 60) could fix a faucet! Years of experience, my ass! Thank you You Tube!
Your video seems the most thorough for my faucet. I replaced the seat and springs, and o-ring around the OUTSIDE of the cartridge, and still had a leak from the bottom. I didn't know there was a o-ring INSIDE AND AROUND the stem of the cartridge until you pulled the cartridge apart! This fixed the leak all the way! Thank you.
Thank you for the helpful video. This was exactly what I needed to stop my kitchen hot water faucet from dripping. When I did this repair just now, it wasn't as easy as it looked in the video. Pulling out the old valve was frustrating. I tried to use the screwdriver to lift it up but it just chipped off little pieces of the plastic on the old valve. (Thankfully I was replacing that too.) I kept wiggling the valve, tapping it, and fiddling around for about 15 minutes, but it wouldn't budge. I finally ended up standing on my counter and using channel locks to grip the thing. It felt like I had to lift with 80 pounds of force to get that thing out. I knew I was risking breaking the whole faucet. But it did finally pop out and the rest of the repair was straightforward. Hats off with deep respect to professional plumbers. I thought my job was frustrating, but you people earn every penny.
Great video. You identified all of the key steps and necessary tools. Another point to share with your viewers is Delta warrantees all of their equipment for life. I simply called them, described the parts I needed and they arrived at my door at no charge.
I learned something from your video. Wish I had seen this before I replaced the entire cartridge $18 at Lowe’s for an original Delta cartridge. I didn’t realize there was a rebuild kit! Anyway, this is an easy fix PROVIDED that infernal setscrew that holds the handle onto the stem doesn’t get stripped when trying to remove it.
Thanks! It was helpful to see what all the parts would look like before I took everything apart. I replaced the entire stem including the spring, O-rings, etc. and my leak stopped. Super easy to do after watching this video!
Thank you r the wonderful tutorial!! I tried for at an hour with the assistance of my uncle and finally we decided to look up on good old RUclips! It then took us under 5 minutes to finish it . Thanks again. I will be downloading this for future reference.😀
I was about to spend $15 a piece for the valve stem, when I saw that you had a repair kit which contained all the o rings and seals. Went to my local "Big box store", and spent $3 and did both hot water faucets in about 20 minuets. Thanks for posting!
Thanks for posting this video. Didn't realize the repair kit included the o-rings. Just a concern with your suggestion using sandpaper to clean the shaft. Be careful what grit paper you use. Too coarse will leave scratches and prevent the o-ring from sealing. Personally I use a 3M Scotch-Brite Ultra Fine pad with vinegar. The vinegar dissolves the film and the pad polishes the shaft.
I just want to add a comment about these DIY videos concerning removal and replacing the cartridge in the faucet. When filming the repair it”s best to make sure the water is removed from inside the hole because if you don’t it creates a glare and you can’t see the spring and seal clearly. I simply used a little bit of toilet paper and stuck it inside the hole to soak up the excess water. I then stuck my little Allen wrench I removed the handle with into the hole and dragged the spring and seal out.
Great video. Works like a charm. Danco parts available at Menards too. I use a little plumbers grease in these parts to extend life and reduce friction on these rubber parts. A Little tube will last a lifetime. Now to tackle the drippy shower.
As to which washer should be replaced, it can summarized that if your faucet is leaking from where the water normally comes out, it is the spring and rubber stem problem. If leaking near the handles, then it is the upper two washers.
Thanks for this. I had fixed/cleaned/lubed a squeaky faucet handle only to notice I now had a leak. Dang it. Tomorrow I'll take it all apart again and see about replacing the o-rings. My o-ring is more flat - not sure if that's because it's a different manufacturer or because it's worn out. Peerless.
worked like a charm! tip for anyone watching this: When you remove the handles, make a mental note (or picture) of the direction of the metal rod and the plastic bumpers. when I put it back together it took a moment to figure out how they should be layed out. The kit only cost 3 dollars! Kit: Danco 88101
I've done this before, but I think I'm gonna go ahead and buy stems while I'm out getting the other repair stuff. Some plumber just wanted to charge me 500 bucks to "rebuild" my faucet. Jut before pandemic, a plumber was going to replace the stem as part of a normal service call for something but he happened to not have the right one with him. Then the world went crazy and I have more drips than I can continue to ignore. I've lost my allen wrench since the last time I did it.
Nice video; thanks. Unfortunately my professional plumber is unable to solve the problem after installing a new cartridge (RP24096) complete with 1/4 turn stop (RP2409) and new seat/spring RP4993. When installed the same direction as it was prior to removing the old cartridge the water does not turn off. However, it does turn off when rotated 180degrees ... but of course that means the handle is facing backwards . Any advice ?
Thanks for the video. I was looking for a particular view and i couldn't. The bottom of the cartridge has one flat side and a hole, which way you'll know that will cover seating stem and shut off the water when twisting the lever? Thanks
Delta does have a good warranty. Our lahara faucet has a 5 year warranty. Was leaking after 2 years. They sent me a cartridge free. And if still leaks will send the whole faucet. I don’t think the cartridges r that expensive so u can get at Lowe’s if your in a hurry
video very detailed but many times could only see arm and hands in front of faucet. Sound is bad. I had my computer volume on high and could hardly hear you. I recommend re-recording this and have someone hole the camera and adjust your volume to loud. You went over some things that other videos did not include, so yours would be the best if you fix the problems that I pointed out.
Thanks, but I’m just a guy trying to help people. I’m not a pro and don’t make money from the videos. I just video things that I fix around the house. :)
When trying to take the handle off on the "cold" side, I discovered that the allen head was stripped. It's obviously recessed inside the handle, which makes it impossible to grab hold of. Any tricks or tips on how to get the stripped allen screw out?
Rolan Watts sure, they make things like “easy outs” for this. You can find it at Home Depot or Lowe’s. They are like a grippy drill bit but it only grips in the reverse direction. Before that you could try taking a tiny flat head screwdriver and gently tap it into the Allen head to see if you can get it to come out. Be careful though because the metal these things are made of is pretty cheap and it’s easy to mess up the threads.
How did the base of the handle of your faucet come off so easily? I removed the set screw from the handle of my Delta faucet but the base of the handle does not pull off like yours does at 0:46. The base on mine is still stuck fast. I can’t lift it off. I even tried turning it to different positions and lifting, thinking maybe it has to be at a certain position before it can be pulled off. Still, it won’t pull off. No matter where I turn it, it won’t come off. Yes, the set screw is removed. What suggestions do you have for how to remove that base? It doesn’t appear to have corrosion around it. The faucet looks nice and new.
Go to a car parts store and buy a set of plastic pry tools. These are typically used to pry up car trim without scratching it. Then try and pry it off. I suspect yours has just been there a long time and needs encouragement to come off…
@@fiveyorks Thank you for the great idea. Do the plastic pry tools look like a flat blade screwdriver? or like a putty knife? I've used both the flat blade screwdriver and the putty knife and tried to pry it off and still it won't come off.
@@KidsandKittens217 darn! Yes they would be like a flathead screwdriver. My only idea is brute force. Get another person and try prying in 2, 3, or even 4 places.
Interesting. I would suggest to get a plastic pry tool set and try to insert it below the handle and force it up. Maybe try two at once on either side. These pry tools are typically used to remove plastic car trim and things like that. Pretty cheap. Or, try a screwdriver and use a rag as to try and minimize the scratching. Good luck!
Great video, thanks! Question tough: if I open the cold handle, it leaks from the bottom of the hot handle. Also dropping below the faucet, under the sink. Any ideas how can I repair?
@@karolyholczhauser1528 Yes, the other cartridge will probably start leaking too. If you have a hot and cold vs a single control, replace them both. That is what I would do.
Take the setscrew all the way out just to make sure it’s not catching. You can order some plastic pry tools for Amazon that are normally used to remove interior parts of cars, and use it on your handle and it won’t scratch. I’d try prying a little more, and then you can get a cloth and use a small hammer and tap on it a little bit all the way around to see if you can break it loose. Put the cloth over The handle so you don’t scratch it with the hammer.
I have replaced the washer on the hot side of a Delta faucet more than once. The last time, I must have screwed something up. Now the handle doesn't hit a stop when the water stops flowing. It can turn in both directions. In the middle of the turns, the water stops. If I turn it left or right, the water starts again. Help!
Quothraven there is a small plastic piece that is in the wrong place or in wrong orientation. Take both faucet handles off and carefully examine the one that works, and then compare that one to the one that does not stop properly. I think you will be able to figure it out!
I have a delta989 DST. I cannot get the lever handle off even after removing the set screw. Can anyone help me. In the original instructions on how to assemble it, it shows it apart and in need of assembly, so I know it comes apart…
Make sure you are turning it clockwise. These valves can sort of freeze up if they are not turned for years. I suggest to take everything out from under the sink and try and position yourself to get a better grip on it. If that doesn’t work you will need to get some large pliers to clamp around it to get mechanical leverage so you can turn it. Before you do this, however, make sure you know where the main water cut off for the house is. If the valve is old it could start leaking, And you would need to turn the water off at the main valve to stop the leak. At that point you probably need a plumber.
I'd say this was a good "How to" video. However, I think you could improve it a bit by clarifying a couple of points. First off you show only that the left faucet stem leaks but proceed to show that you are replacing both sides. There are different opinions as to whether it's a good idea to replace the other side for preventive maintenance. Why not wait to until and/or if there is a problem with the other side. i.e.-Leave well enough alone. Secondly, The base seal only needs changing if the faucet is dripping. While the o-rings, of course, are for sealing of the stem. At a minimum probably should point that out. Save all those parts for when you need them. Again, leave well enough alone.
I will never buy another delta faucet. The shower tap cartridges have too many pieces and are too finicky to replace and don't last, too much stress. Too many trips up and down the stairs turning the water off and on. Complete hassle. Never again.
Thank you! I am a 74 yr. old widow and I have learned these hired repairmen know how to take advantage of "old ladies"; and, the legit repair people know how to charge. With the help of your video and the helpful man at Lowes, I was able to fix my leaky faucet myself! Thank you.
Pam Richardson I just went to the hardware store to get the replacement gasket and sprinkler parts - the old guy looked at me and asked if I was going to try to do it myself - I said “YES, I SURE AM!” To which he replied that usually took years of experience. I asked him if he didn’t think a woman (I;m 60) could fix a faucet! Years of experience, my ass! Thank you You Tube!
@@festivalmama You tube university graduate. COOL.
Your video seems the most thorough for my faucet. I replaced the seat and springs, and o-ring around the OUTSIDE of the cartridge, and still had a leak from the bottom. I didn't know there was a o-ring INSIDE AND AROUND the stem of the cartridge until you pulled the cartridge apart! This fixed the leak all the way! Thank you.
Glad it helped!
Thank you for the helpful video. This was exactly what I needed to stop my kitchen hot water faucet from dripping. When I did this repair just now, it wasn't as easy as it looked in the video. Pulling out the old valve was frustrating. I tried to use the screwdriver to lift it up but it just chipped off little pieces of the plastic on the old valve. (Thankfully I was replacing that too.) I kept wiggling the valve, tapping it, and fiddling around for about 15 minutes, but it wouldn't budge. I finally ended up standing on my counter and using channel locks to grip the thing. It felt like I had to lift with 80 pounds of force to get that thing out. I knew I was risking breaking the whole faucet. But it did finally pop out and the rest of the repair was straightforward. Hats off with deep respect to professional plumbers. I thought my job was frustrating, but you people earn every penny.
Great video. You identified all of the key steps and necessary tools. Another point to share with your viewers is Delta warrantees all of their equipment for life. I simply called them, described the parts I needed and they arrived at my door at no charge.
This video helped so much. Had you not mentioned the spring and the plug I would have never known. I almost bought a new faucet. Thank you so much!
I learned something from your video. Wish I had seen this before I replaced the entire cartridge $18 at Lowe’s for an original Delta cartridge. I didn’t realize there was a rebuild kit! Anyway, this is an easy fix PROVIDED that infernal setscrew that holds the handle onto the stem doesn’t get stripped when trying to remove it.
Watched a few videos on Delta faucet repairs. This one has been the best with the level of detail provided. Well done & Thanks!
I wish that I watched this before I spent the money buying the cartridges.
A very well made and thought out tutorial!
Thank You!
Thanks! It was helpful to see what all the parts would look like before I took everything apart. I replaced the entire stem including the spring, O-rings, etc. and my leak stopped. Super easy to do after watching this video!
Thank you r the wonderful tutorial!! I tried for at an hour with the assistance of my uncle and finally we decided to look up on good old RUclips! It then took us under 5 minutes to finish it . Thanks again. I will be downloading this for future reference.😀
Thank you so much! I too was going to replace the whole cartridge until I saw your video, but it was just the O-rings! Saved me so much money!
big thank you, only cost me $7.00. your little hints were everything I needed. stay safe.
I was about to spend $15 a piece for the valve stem, when I saw that you had a repair kit which contained all the o rings and seals. Went to my local "Big box store", and spent $3 and did both hot water faucets in about 20 minuets. Thanks for posting!
Brad Davies me too!
And me!
Thank You for making this how to repair video.
What I really loved about your video.
Is that you got straight to the point
On how to fix this.
Thanks!
Thanks for posting this video. Didn't realize the repair kit included the o-rings. Just a concern with your suggestion using sandpaper to clean the shaft. Be careful what grit paper you use. Too coarse will leave scratches and prevent the o-ring from sealing. Personally I use a 3M Scotch-Brite Ultra Fine pad with vinegar. The vinegar dissolves the film and the pad polishes the shaft.
I just want to add a comment about these DIY videos concerning removal and replacing the cartridge in the faucet. When filming the repair it”s best to make sure the water is removed from inside the hole because if you don’t it creates a glare and you can’t see the spring and seal clearly. I simply used a little bit of toilet paper and stuck it inside the hole to soak up the excess water. I then stuck my little Allen wrench I removed the handle with into the hole and dragged the spring and seal out.
Thanks for the video. I had replaced both cartridges and still had a leak. This solved my problem.
Great video. Works like a charm. Danco parts available at Menards too. I use a little plumbers grease in these parts to extend life and reduce friction on these rubber parts. A Little tube will last a lifetime. Now to tackle the drippy shower.
World class video! Well done! I especially like the detail picture at the beginning. Also like the way u emphasized the washer sd b proprtly seated
Thanks!
As to which washer should be replaced, it can summarized that if your faucet is leaking from where the water normally comes out, it is the spring and rubber stem problem. If leaking near the handles, then it is the upper two washers.
Thanks for this. I had fixed/cleaned/lubed a squeaky faucet handle only to notice I now had a leak. Dang it. Tomorrow I'll take it all apart again and see about replacing the o-rings. My o-ring is more flat - not sure if that's because it's a different manufacturer or because it's worn out. Peerless.
worked like a charm! tip for anyone watching this: When you remove the handles, make a mental note (or picture) of the direction of the metal rod and the plastic bumpers. when I put it back together it took a moment to figure out how they should be layed out. The kit only cost 3 dollars! Kit: Danco 88101
Thank you! My husband and I successfully fixed our faucet with your help!
I've done this before, but I think I'm gonna go ahead and buy stems while I'm out getting the other repair stuff. Some plumber just wanted to charge me 500 bucks to "rebuild" my faucet. Jut before pandemic, a plumber was going to replace the stem as part of a normal service call for something but he happened to not have the right one with him. Then the world went crazy and I have more drips than I can continue to ignore. I've lost my allen wrench since the last time I did it.
Nice video; thanks. Unfortunately my professional plumber is unable to solve the problem after installing a new cartridge (RP24096) complete with 1/4 turn stop (RP2409) and new seat/spring RP4993. When installed the same direction as it was prior to removing the old cartridge the water does not turn off. However, it does turn off when rotated 180degrees ... but of course that means the handle is facing backwards . Any advice ?
Great video! I had complete success using the same replacement parts kit from Lowe's. Thanks for sharing.
June Abrams great job June!
Thanks! Better detail than other videos I've watched.
Thanks for the video. I was looking for a particular view and i couldn't. The bottom of the cartridge has one flat side and a hole, which way you'll know that will cover seating stem and shut off the water when twisting the lever?
Thanks
Great video. Much appreciate the level of detail.
new subscriber!! thanks for this, others didn't detail the spring and o ring on spring. thank you for helping me out!!!!!
The cartridge DOES NOT lift out. It's stuck! I tried a screw driver, pliers, cannel locks and even extra force. Is the faucet beyond repair?
Delta does have a good warranty. Our lahara faucet has a 5 year warranty. Was leaking after 2 years. They sent me a cartridge free. And if still leaks will send the whole faucet. I don’t think the cartridges r that expensive so u can get at Lowe’s if your in a hurry
video very detailed but many times could only see arm and hands in front of faucet. Sound is bad. I had my computer volume on high and could hardly hear you. I recommend re-recording this and have someone hole the camera and adjust your volume to loud. You went over some things that other videos did not include, so yours would be the best if you fix the problems that I pointed out.
Thanks, but I’m just a guy trying to help people. I’m not a pro and don’t make money from the videos. I just video things that I fix around the house. :)
Grate video, also you are good a explaining the process.
Thanks!
Awesome video man 😎
Look at all that rubber rubbing off. Imagine drinking that
Wow very helpful. Thanks!
When trying to take the handle off on the "cold" side, I discovered that the allen head was stripped. It's obviously recessed inside the handle, which makes it impossible to grab hold of. Any tricks or tips on how to get the stripped allen screw out?
Rolan Watts sure, they make things like “easy outs” for this. You can find it at Home Depot or Lowe’s. They are like a grippy drill bit but it only grips in the reverse direction. Before that you could try taking a tiny flat head screwdriver and gently tap it into the Allen head to see if you can get it to come out.
Be careful though because the metal these things are made of is pretty cheap and it’s easy to mess up the threads.
thank you!
Really good video. Thank you.
How did the base of the handle of your faucet come off so easily? I removed the set screw from the handle of my Delta faucet but the base of the handle does not pull off like yours does at 0:46.
The base on mine is still stuck fast. I can’t lift it off. I even tried turning it to different positions and lifting, thinking maybe it has to be at a certain position before it can be pulled off. Still, it won’t pull off. No matter where I turn it, it won’t come off. Yes, the set screw is removed. What suggestions do you have for how to remove that base? It doesn’t appear to have corrosion around it. The faucet looks nice and new.
Go to a car parts store and buy a set of plastic pry tools. These are typically used to pry up car trim without scratching it. Then try and pry it off.
I suspect yours has just been there a long time and needs encouragement to come off…
@@fiveyorks Thank you for the great idea. Do the plastic pry tools look like a flat blade screwdriver? or like a putty knife? I've used both the flat blade screwdriver and the putty knife and tried to pry it off and still it won't come off.
@@KidsandKittens217 darn! Yes they would be like a flathead screwdriver. My only idea is brute force. Get another person and try prying in 2, 3, or even 4 places.
Great video. Can you tell me how I get the part numbers for the orings
Thank you Sir!
Thanks guy, save my money!!!
Question, what are the danco o ring numbers that you used, you used.two different o rings on the cartridge?? On the delta RP22513
Thanks!
that's great, what about the washer on the hand controller of their touch faucet? tx
Thanks man!
Thank you ... your video was perfect to guide me through this diy fix :-)
What size allen wrench did you use? & it seems hard to find ones that are long enough to reach the nut these days
When I removed the set screw with an Allen wrench, I then couldn’t get the handle off, it was like, stuck on, should I just force it?
Interesting. I would suggest to get a plastic pry tool set and try to insert it below the handle and force it up. Maybe try two at once on either side. These pry tools are typically used to remove plastic car trim and things like that. Pretty cheap. Or, try a screwdriver and use a rag as to try and minimize the scratching. Good luck!
Did you get it off?
Great video, thanks!
Question tough: if I open the cold handle, it leaks from the bottom of the hot handle. Also dropping below the faucet, under the sink. Any ideas how can I repair?
Make the repairs as he did in the video on both sides, hot and cold, that should stop the leaking. Turn the water off under the sink before you start.
Chuck CTS-V thanks for getting back to me. So should I replace cartridge even it’s dropping from the middle?
@@karolyholczhauser1528 Yes, the other cartridge will probably start leaking too. If you have a hot and cold vs a single control, replace them both. That is what I would do.
Asante sana kaka
I undid the set screw but can’t get the handle off. I tried to pry a little but I don’t want to break it. Any suggestions?
Take the setscrew all the way out just to make sure it’s not catching. You can order some plastic pry tools for Amazon that are normally used to remove interior parts of cars, and use it on your handle and it won’t scratch.
I’d try prying a little more, and then you can get a cloth and use a small hammer and tap on it a little bit all the way around to see if you can break it loose. Put the cloth over The handle so you don’t scratch it with the hammer.
I have replaced the washer on the hot side of a Delta faucet more than once. The last time, I must have screwed something up. Now the handle doesn't hit a stop when the water stops flowing. It can turn in both directions. In the middle of the turns, the water stops. If I turn it left or right, the water starts again. Help!
Quothraven there is a small plastic piece that is in the wrong place or in wrong orientation. Take both faucet handles off and carefully examine the one that works, and then compare that one to the one that does not stop properly. I think you will be able to figure it out!
I have a delta989 DST. I cannot get the lever handle off even after removing the set screw. Can anyone help me. In the original instructions on how to assemble it, it shows it apart and in need of assembly, so I know it comes apart…
tapered end of spring goes down. 😌
What do we do when it still leaks around the Base? WTF
That’s okay. Happens all the time. Just slowly take it apart and put it back together. The lower most seal may be the issue.
I tried turning off shutoff valve but it doesn't move so I can turn off water from faucet
Make sure you are turning it clockwise. These valves can sort of freeze up if they are not turned for years. I suggest to take everything out from under the sink and try and position yourself to get a better grip on it. If that doesn’t work you will need to get some large pliers to clamp around it to get mechanical leverage so you can turn it. Before you do this, however, make sure you know where the main water cut off for the house is. If the valve is old it could start leaking, And you would need to turn the water off at the main valve to stop the leak. At that point you probably need a plumber.
good
I'd say this was a good "How to" video. However, I think you could improve it a bit by clarifying a couple of points.
First off you show only that the left faucet stem leaks but proceed to show that you are replacing both sides. There are different opinions as to whether it's a good idea to replace the other side for preventive maintenance. Why not wait to until and/or if there is a problem with the other side. i.e.-Leave well enough alone.
Secondly, The base seal only needs changing if the faucet is dripping. While the o-rings, of course, are for sealing of the stem. At a minimum probably should point that out. Save all those parts for when you need them. Again, leave well enough alone.
Diehard I agree with you. Only the base seal needs to be replaced.
Raul Banuelos but the faucet wasn’t dripping. It was leading from the handle base
just an fyi
delta has lifetime warranty
i went to the store and got a replacement cartridge for free
did you have to have proof of purchase or packaging?
you really cant get away from plastics can we
I will never buy another delta faucet. The shower tap cartridges have too many pieces and are too finicky to replace and don't last, too much stress. Too many trips up and down the stairs turning the water off and on. Complete hassle. Never again.