Do’s And Don’ts When Drilling, Cutting & Notching A Hole Through Wood Stud Framing! | DIY Tips!
HTML-код
- Опубликовано: 22 мар 2022
- ITEMS I USED:
- Steel Plate Stud Shield - amzn.to/358XByI
- IRC 2021 Code Book - amzn.to/3quvktW
- Oscillating Tool - amzn.to/3tys96a
- 25’ Tape Measure - amzn.to/3tyU0Dp
- Stud Finder Tool - amzn.to/3txCLCj
- Voltage Detector- amzn.to/36gTIZe
SHOP MY ONLINE AMAZON STORE AND CHECK OUT ALL THE TOOLS I USE!
www.amazon.com/shop/genevo9
On this episode I'm going to show you the Do’s And Don’ts When Drilling , Cutting & Notching A Hole Through A Wood Stud Framing! DIY Tips tutorial for Beginners!
HERE ARE THE CODE CHAPTERS REFERENCED ON THIS VIDEO:
International Residential Code:
- R602.6 (Drilling and notching of studs)
- P2603.2.1 (Protection against physical damage) Structural and Piping Protection
- TABLE E3802.1 (Chapter 3) General Installation And Support Requirements For Wiring Methods
DO YOU HAVE QUESTIONS ON YOUR HOME REPAIR OR DIY PROJECT? GET TIPS, ADVICE AND ANSWERS! BECOME A FIX THIS HOUSE MEMBER!
Become a FIX THIS HOUSE Member by clicking on this link: / fixthishouse
Please Subscribe To Our Channel! / fixthishouse
FOR BUSINESS INQUIRES SEND TO:
FIX THIS HOUSE
P.O. BOX 2511
BREMERTON, WA 98310
UNITED STATES
FOR BUSINESS INQUIRES EMAIL ME AT:
fixthishouse1@yahoo.com
DISCLAIMER:
Videos produced by Fix This House are provided for informational, educational and entertainment purposes only. Please use SAFETY precautions when following the tutorials on these videos. Viewers doing projects at their own home are doing it at their own risk and Fix This House cannot be held liable if they cause damage to their homes or injury. Fix This House cannot claim liability with all applicable laws, rules, codes and regulations for a project. Always stay informed of your local building codes! Happy and SAFE renovating!
#Studs #Notching #Woodframing - Хобби
If you use a notch in a 2x4 and plan to run wires or plumbing through them, it is absolutely necessary to put a steel plate over the notch. In my opinion, notching a 2x4 is a just a bad idea. If you don't steel plate the notch, and someone hangs a picture and nails through to the wiring or plumbing, and the nail hits it ... you're screwed.
You can't tell me that last bit wasn't a pun. If it was intentionally a pun, you nailed it.
Thank you for this video. Very clear and succinct, easy to follow for a newbie
Big thanks for this video! Super clear and concise. Saved me time learning!
Great video thanks bro !
Another great video. Would be very helpful if you put out another one for top plates and other studs of studs.
How many notches can be made on one load bearing stud?
Good video 👍. What is the code for notching a fire block stud on an exterior wall?
How many holes can you put in the same 2×4?
How many holes can you put in the same 2x4
Hello! I'm an apprentice plumber. Im studying mechanical properties and protection of building materials and structures. My book says maximum diameter of bored hole is 40% of stud depth, not %60. That limitation is for boring in interior partition. Can you double check please?
I recently had my bathroom remodeled. The idiot contractor notched out the interior corner studs for the water pipes but the notches are about 70% of the stud. Each stud has two notches. How do I go about attempting to fix this? How can I add stability back to the studs ?
In the case of a load bearing stud isn't the depth about 1 1/2 " instead of 3 1/2? Isn't 3 1/2 " the width?
You would not want a long notch because assuming it’s 2X4’s and your 7/8 inches deep, you need to cover plate the wiring. At that depth, I would also cover EMT, I’ve seen people drill dry wall screws dead center into piping. I almost always drill holes, not crazy about notching.
You said dont put notch and hole in same area/level but what should be min. vertical distance between them?
GERAT
Thank you!
What is the minimum location that the bored hole can be below or above the notch?
Hi! I didn’t see anything on the code, just says nothing within the cross section of the notch 🙏🏽😊👍🏽
Is it necessary for bad music to be 3 times as loud as audio ?
If the wall is non load, why can't you cut more than 25??
The stud still needs to be able to support its own weight, plus the weight of the drywall attached to it, as well as resist buckling due to lateral force (like if a person or a piece of furniture leans against it)