Это видео недоступно.
Сожалеем об этом.
Worcester Boiler, empty syphon blocked,
HTML-код
- Опубликовано: 12 дек 2022
- I should say that I did this whilst the blue and red lights were flashing - so I would suggest you do the same and wait till the green boiler light (the flame symbol (🔥) at top-left on the display cover) is OFF before removing the cap.
All the best to everyone out there!
Also thank you @peterwang4307! I followed the instructions on you insightful Worcester boiler syphon video ( • Worcester boiler, syph... ) and it worked fantastically. I did this video to show the results. Over an hour later, everything on the boiler is still working brilliantly. Thanks again.
P.S: some people on Peter’s video commented that the procedure was unsafe and you needed a Corgi approved gas plumber to do this otherwise it was unsafe. IT IS NOT UNSAFE. There is no need to touch or go near the internal system or shut any gas off - it’s nothing more than taking a cap off a valve with a bucket under it.
Christmas eve and our boiler has been out since 1 am last night. Cant thank you and Peter Wang enough dude. I did this and 5 minutes later my boiler has come back to life! Thank you!
Best feeling ever huh? Go well :-)
If your condensate trap is filled with gunk & grey water, the boiler has not been serviced for a while, and now your pressure vessel is also on its way.
i have the same boiler and i would guess the drain pipe was frozen outside and that is why you got the build up and it may happen again if the pipe is still frozen stopping the syphon from emptying
Get that boiler serviced. Pressure gauge is far to high, heat exchanger needs a cleaning, burner seal probably gone.
You still have an issue as it is overpressurising ...expansion vessel is empty of air prv opens at 3 bar ..i think they should run at about 2bar
@Silverback Matt also the PRV should kick in about 3 bar and he is at 4 bar .And with it being in the RED it should alert him that something is wrong
Thanks for highlighting - yes I clocked that and was able to bleed a radiator to release some of the pressure after uploading this video. I'd topped the water up right to the max of the green line but when the boiler started working again the pressure went up a bit more. Well spotted.
thank you
Did you have to refill the syphon after you emptied it. I think I have the same problem now, and it's due to be minus for the next few days.
HI there - no, should be nothing to refill, you just pop off that cap on the siphon and have a bucket etc under to catch the water / grit - then replace the cap and press reset boiler (I turned both the hot water + central heating settings to 'off' (vs on / twice / etc) but that was just to be safe), once reset, everything should come back on - but it's likely this cycle will repeat because basically the outside pipe where all this water should be draining to is frozen = water can't deposit = fills that siphon = boiler shuts off! So cap - bucket - reset. Guess if you smell gas etc - then you gotta call the gas people/plumbers etc but hoping you get through this cold snap and great if this measure helps you out!
Could you please tell me the model number of this boiler.cant find it anywhere
Why the boiler so low
Ha --I know, right? Was a rental so that's how they did it. Fun times. Hope you well and managed to sort your issue out ✌
As an experienced and qualified gas engineer... Would just like to say please don't attempt what you are watching on RUclips...
You may think you're doing a great DIY job.. But there is a simple reason we have to train every 5 years to stay qualified and there is a simple reason you are not a qualified plumbing and gas engineer...
It's about the safety aspects..
All you have done is now created anpther problem..
Just get a qualified engineer round once a y tree ar for a service to keep your boiler in good health..
There are defects on that specific boiler that you won't even know about that COULD be harmful to your health.
I don't play with the brakes on my car, why... Because I'm. Not a mechanic.. The principle is simple enough but I don't know what to do when or if I'm doing it wrong from watching a RUclips video.
Stay safe
1) my boiler is now fixed and working again
2) as I made sure to state several times in the video - no gas-related elements are manipulated; you're taking a cap off a tube and releasing some water, then pressing restart on your boiler
3) when there are no engineers available for hours or days, and with cost-of-living crisis squeezing people left right and centre, people will need help and safe solutions that they can try at no cost - that is exactly what this video is.
4) I also had a newborn, and this was during the horrid cold snap - so if there's a non-gas based solution I can try as the house begins to freeze and there is no water in the house, then any reasonable human adult is going to try that option!
5) the engineer came out and re-confirmed that every step taken was measured and accurate.
6) have a great day and Merry Christmas!!
Wow, so you can't change your brakes that mean no one should clean the trap on the boiler surely you also calling spark to change your light bulb...
@@Sekcjakomentarzyy
Bless. Its not about being able to or not being able to.. Its about knowing what you are doing, why you are doing it and what to do of it goes wrong.. Which if you aren't experienced in a certain trade the physical act may look simple.. But if you have next to no idea what could go wrong... You may never be lucky enough to know.
But you crack on bud
What you have emptied out is a condensate trap, this needs to be refilled with water after emptying. The reason being it acts just like the trap under your sink. Having the condensate trap full of water stops the poisonous flue fumes from coming through the trap.